Yi Feng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yi Feng has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
Gaojie Yan
Hebei Key Laboratory of Functional Polymers, Department of Polymer Materials and Engineering, Hebei University of Technology, Tianjin 300400, P. R. China
1 shared publication- Haifeng Ji
Hebei Key Laboratory of Functional Polymers, Department of Polymer Materials and Engineering, Hebei University of Technology, 8 Guangrong Street, Tianjin 300130, China
1 shared publication - Jingjing Shi
School of Science, Nantong University, Nantong 226019, Jiangsu Province, People’s Republic of China
1 shared publication Li Chen
Hebei Key Laboratory of Functional Polymers, Department of Polymer Materials and Engineering, Hebei University of Technology, Tianjin 300400, P. R. China
1 shared publication- Shuang Lian
Hebei Key Laboratory of Functional Polymers, Department of Polymer Materials and Engineering, Hebei University of Technology, 8 Guangrong Street, Tianjin 300130, China
1 shared publication Shuo Wang
Hebei Key Laboratory of Functional Polymers, Department of Polymer Materials and Engineering, Hebei University of Technology, Tianjin 300400, P. R. China
1 shared publication
Latest Publications
- Open Access
- 15 June 2023
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 13 (27) , 18488-18495
“d-electron interactions” induced CoV2O6–Fe–NF for efficient oxygen evolution reaction
Through a redox reaction, Fe2+ was introduced into CoV2O6-NF and was transformed into high oxidation state Fe(2+δ)+, acting as a partial active center to accelerate the OER process. CoV2O6-Fe-NF exhibited an overpotential of 298 mV at 100 mA cm−2.
- 15 June 2023
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 13 (27) , 18488-18495
Open Access“d-electron interactions” induced CoV2O6–Fe–NF for efficient oxygen evolution reaction
Through a redox reaction, Fe2+ was introduced into CoV2O6-NF and was transformed into high oxidation state Fe(2+δ)+, acting as a partial active center to accelerate the OER process. CoV2O6-Fe-NF exhibited an overpotential of 298 mV at 100 mA cm−2.
- Open Access
- 29 September 2021
- Published by MDPI AG in Nanomaterials
- Vol. 11 (10) , 2562
Cationic Cyclopropenium-Based Hyper-Crosslinked Polymer Enhanced Polyethylene Oxide Composite Electrolyte for All-Solid-State Li-S Battery
The development of solid-state polymer electrolytes is an effective way to overcome the notorious shuttle effect of polysulfides in traditional liquid lithium sulfur batteries. In this paper, cationic cyclopropenium based cross-linked polymer was firstly prepared with the one pot method, and then the counter ion was replaced by TFSI− anion using simple ion replacement. Cationic cyclopropenium hyper-crosslinked polymer (HP) was introduced into a polyethylene oxide (PEO) matrix with the solution casting method to prepare a composite polymer electrolyte membrane. By adding HP@TFSI to the PEO-based electrolyte, the mechanical and electrochemical properties of the solid-state lithium-sulfur batteries were significantly improved. The PEO-20%HP@TFSI electrolyte shows the highest Li+ ionic conductivity at 60 °C (4.0 × 10−4 S·cm−1) and the highest mechanical strength. In the PEO matrix, uniform distribution of HP@TFSI inhibits crystallization and weakens the interaction between each PEO chain. Compared with pure PEO/LiTFSI electrolyte, the PEO-20%HP@TFSI electrolyte shows lower interface resistance and higher interface stability with lithium anode. The lithium sulfur battery based on the PEO-20%HP@TFSI electrolyte shows excellent electrochemical performance, high Coulombic efficiency and high cycle stability. After 500 cycles, the capacity of the lithium-sulfur battery based on PEO-20%HP@TFSI electrolytes keeps approximately 410 mAh·g−1 at 1 C, the Coulomb efficiency is close to 100%, and the cycle capacity decay rate is 0.082%.
- 29 September 2021
- Published by MDPI AG in Nanomaterials
- Vol. 11 (10) , 2562
Open AccessCationic Cyclopropenium-Based Hyper-Crosslinked Polymer Enhanced Polyethylene Oxide Composite Electrolyte for All-Solid-State Li-S Battery
The development of solid-state polymer electrolytes is an effective way to overcome the notorious shuttle effect of polysulfides in traditional liquid lithium sulfur batteries. In this paper, cationic cyclopropenium based cross-linked polymer was firstly prepared with the one pot method, and then the counter ion was replaced by TFSI− anion using simple ion replacement. Cationic cyclopropenium hyper-crosslinked polymer (HP) was introduced into a polyethylene oxide (PEO) matrix with the solution casting method to prepare a composite polymer electrolyte membrane. By adding HP@TFSI to the PEO-based electrolyte, the mechanical and electrochemical properties of the solid-state lithium-sulfur batteries were significantly improved. The PEO-20%HP@TFSI electrolyte shows the highest Li+ ionic conductivity at 60 °C (4.0 × 10−4 S·cm−1) and the highest mechanical strength. In the PEO matrix, uniform distribution of HP@TFSI inhibits crystallization and weakens the interaction between each PEO chain. Compared with pure PEO/LiTFSI electrolyte, the PEO-20%HP@TFSI electrolyte shows lower interface resistance and higher interface stability with lithium anode. The lithium sulfur battery based on the PEO-20%HP@TFSI electrolyte shows excellent electrochemical performance, high Coulombic efficiency and high cycle stability. After 500 cycles, the capacity of the lithium-sulfur battery based on PEO-20%HP@TFSI electrolytes keeps approximately 410 mAh·g−1 at 1 C, the Coulomb efficiency is close to 100%, and the cycle capacity decay rate is 0.082%.