Mohammad S. Bagazi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Mohammad S. Bagazi has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Abdulmohsen Omar Alsaiari
Center of Excellence in Desalination Technology, King Abdulaziz University, Jeddah 21589, Saudi Arabia
1 shared publication - Ahmed Bakr Khoshaim
Department of Mechanical Engineering, King Abdulaziz University, Jeddah, 22254, Saudi Arabia
1 shared publication - Ammar Abdulghani Melaibari
Department of Mechanical Engineering, Faculty of Engineering, King Abdulaziz University, Jeddah 21589, Saudi Arabia
1 shared publication - Hani Abulkhair
Department of Mechanical Engineering, Faculty of Engineering, King Abdulaziz University, P.O. Box 80204, Jeddah 21589, Saudi Arabia
1 shared publication - Nidal H. Abu-Hamdeh
Center of Research Excellence in Renewable Energy and Power Systems/Energy Efficiency Group, Department of Mechanical Engineering, Faculty of Engineering, King Abdulaziz University
1 shared publication
Latest Publications
- Open Access
- 2 October 2021
- Published by MDPI AG in Sustainability
- Vol. 13 (19) , 10965
Using Phase Change Materials (PCMs) in a Hot and Humid Climate to Reduce Heat Gain and Energy Consumption
Twenty percent of the world’s energy is consumed by the construction sector, including commercial and residential buildings, where 13% is consumed by the residential sector only. Half of the total energy consumed by buildings in Saudi Arabia is specifically attributed to the hot summer season, which, unlike in many other countries in the Middle East, continues for more than 5 months annually. The use of a phase change material (PCM), as an insulator in building materials, can be a solution to provide a comfortable indoor temperature and reduce energy consumption. This study examined two different melting ranges for PCMs RT35 and RT35HC inserted into hollow clay bricks to investigate their thermal behavior and heat storage capacity and compare them with polystyrene foam. To perform this experiment, four chambers were constructed using cement plastering. The data were collected at Jeddah, Saudi Arabia, from mid-November 2020 to the end of February 2021. When the highest temperature was reached during the experiment, PCM RT35 provided a better cooling effect by 13% compared to 24% and 28.56% for PCM RT35HC and foam, respectively, compared to hollow bricks alone. However, when the lowest temperature was reached during the experiment, PCM RT35HC performed better than the other chambers in saving energy and keeping the chamber warm, which was 9.5% for the reference chamber, 7.0% for the foam chamber, and 2.8% for PCM RT35. The maximum energy saving of PCM RT35 was around 1920 kJ, which is around 0.533 kWh, for one wall only, and for PCM RT35HC, it was 2880 kJ, or 0.8 kWh, which can reduce energy consumption of the HVAC system by 97 kWh/m2 and 146 kWh/m2 per year, respectively.
- 2 October 2021
- Published by MDPI AG in Sustainability
- Vol. 13 (19) , 10965
Open AccessUsing Phase Change Materials (PCMs) in a Hot and Humid Climate to Reduce Heat Gain and Energy Consumption
Twenty percent of the world’s energy is consumed by the construction sector, including commercial and residential buildings, where 13% is consumed by the residential sector only. Half of the total energy consumed by buildings in Saudi Arabia is specifically attributed to the hot summer season, which, unlike in many other countries in the Middle East, continues for more than 5 months annually. The use of a phase change material (PCM), as an insulator in building materials, can be a solution to provide a comfortable indoor temperature and reduce energy consumption. This study examined two different melting ranges for PCMs RT35 and RT35HC inserted into hollow clay bricks to investigate their thermal behavior and heat storage capacity and compare them with polystyrene foam. To perform this experiment, four chambers were constructed using cement plastering. The data were collected at Jeddah, Saudi Arabia, from mid-November 2020 to the end of February 2021. When the highest temperature was reached during the experiment, PCM RT35 provided a better cooling effect by 13% compared to 24% and 28.56% for PCM RT35HC and foam, respectively, compared to hollow bricks alone. However, when the lowest temperature was reached during the experiment, PCM RT35HC performed better than the other chambers in saving energy and keeping the chamber warm, which was 9.5% for the reference chamber, 7.0% for the foam chamber, and 2.8% for PCM RT35. The maximum energy saving of PCM RT35 was around 1920 kJ, which is around 0.533 kWh, for one wall only, and for PCM RT35HC, it was 2880 kJ, or 0.8 kWh, which can reduce energy consumption of the HVAC system by 97 kWh/m2 and 146 kWh/m2 per year, respectively.