Dongsik Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Dongsik Kim has a total of 84 co-authors. Here are the top co-authors by number of shared publications:
- Arif Hussain
Department of Mechanical Convergence Engineering, Hanyang University, Seoul 04763, Korea
7 shared publications - Jeonghong Ha
Smart Forming Process Group, Korea Institute of Industrial Technology (KITECH), Ulsan 44776, Republic of Korea
7 shared publications Sun Rock Choi
Department of Mechanical Engineering, POSTECH, Pohang, Republic of Korea
6 shared publications- Junghoon Lee5 shared publications
Changho Seo
Department of Mechanical Engineering, POSTECH (Pohang University of Science and Technology), Pohang, Republic of Korea
4 shared publications- Hyoung Seop Kim
Department of Materials Science and Engineering, Pohang University of Science and Technology (POSTECH), Pohang, Republic of Korea
4 shared publications
Latest Publications
- 13 August 2026
- Published by Elsevier in Additive Manufacturing
- Vol. 128
Fabrication of Ti-6Al-4V structures with superior elongation by laser powder bed fusion combined with induction heating
- 13 August 2026
- Published by Elsevier in Additive Manufacturing
- Vol. 128
Fabrication of Ti-6Al-4V structures with superior elongation by laser powder bed fusion combined with induction heating
- Open Access
- 10 June 2026
- Published by Elsevier in SSRN Electronic Journal
A novel optical scanning system for laser machining of vertical sidewall
Despite its many advantages, laser micromachining has limitations, such as tapering due to plasma-induced distortion, gaussian beam profiles, and defocusing effects. To overcome the tapering limitations of machined surfaces, this study developed a novel optical scanning system and proposed a derived machining process. The proposed optical scanning system controls the angle of incidence (AOI) of the laser beam on the sample surface through a novel arrangement of spherical lenses. The measured angle was 4.058°, closely matching the simulation results. The developed process demonstrated that near-vertical sidewall machining could be achieved at an AOI of 4.058° by appropriately controlling the fluence, overlap ratio, and scan number. Furthermore, we observed that the taper angle during machining was highly sensitive to the AOI. The proposed method has the potential to limit the formation of taper angles in conventional laser machining and enhance industrial applicability through an optical design-based AOI control system.
- 10 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessA novel optical scanning system for laser machining of vertical sidewall
Despite its many advantages, laser micromachining has limitations, such as tapering due to plasma-induced distortion, gaussian beam profiles, and defocusing effects. To overcome the tapering limitations of machined surfaces, this study developed a novel optical scanning system and proposed a derived machining process. The proposed optical scanning system controls the angle of incidence (AOI) of the laser beam on the sample surface through a novel arrangement of spherical lenses. The measured angle was 4.058°, closely matching the simulation results. The developed process demonstrated that near-vertical sidewall machining could be achieved at an AOI of 4.058° by appropriately controlling the fluence, overlap ratio, and scan number. Furthermore, we observed that the taper angle during machining was highly sensitive to the AOI. The proposed method has the potential to limit the formation of taper angles in conventional laser machining and enhance industrial applicability through an optical design-based AOI control system.
- 14 October 2025
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 346
Interfacial behaviours of Sn-Ti/graphite system bonded via ultrasonic-vibration–assisted metallization
- 14 October 2025
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 346
Interfacial behaviours of Sn-Ti/graphite system bonded via ultrasonic-vibration–assisted metallization
- Open Access
- 10 October 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 39, 3901-3914
Optimization of laser powder bed fusion process to enhance mechanical properties of as-built Ti–6Al–4V samples
- 10 October 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 39, 3901-3914
Open AccessOptimization of laser powder bed fusion process to enhance mechanical properties of as-built Ti–6Al–4V samples
- Open Access
- 29 July 2025
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 10 (12) , 10929-10945
Critical geometrical constraints and buckling phenomena in Ti6Al4V ultra-thin walls printed by laser-based powder bed fusion
- 29 July 2025
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 10 (12) , 10929-10945
Open AccessCritical geometrical constraints and buckling phenomena in Ti6Al4V ultra-thin walls printed by laser-based powder bed fusion
- 21 July 2025
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 303
Thermal and flow fields-guided defect-free laser polishing of fused silica
- 21 July 2025
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 303
Thermal and flow fields-guided defect-free laser polishing of fused silica
- 23 November 2024
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 10 (8) , 4349-4374
Transforming biofabrication with powder bed fusion additive manufacturing technology: from personalized to multimaterial solutions
- 23 November 2024
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 10 (8) , 4349-4374
Transforming biofabrication with powder bed fusion additive manufacturing technology: from personalized to multimaterial solutions
- 24 October 2024
- Published by Elsevier in Optics & Laser Technology
- Vol. 181
Development of laser powder bed fusion technology using consolidated powder formed by infrared heating as support structure
- 24 October 2024
- Published by Elsevier in Optics & Laser Technology
- Vol. 181
Development of laser powder bed fusion technology using consolidated powder formed by infrared heating as support structure