Felix Harst
Research Subjects
Felix Harst has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Michael Friedrich Zaeh
Institute for Machine Tools and Industrial Management, TUM School of Engineering and Design, Technical University of Munich, Garching Near Munich, Germany
3 shared publications - Sophie Grabmann
TUM School of Engineering and Design Technical University of Munich Institute for Machine Tools and Industrial Management (iwb) Garching Germany
3 shared publications Michael F. Zaeh
Technical University of Munich, TUM School of Engineering and Design, Institute for Machine Tools and Industrial Management (iwb) , Boltzmannstraße 15, 85748 Garching, Germany
2 shared publications- Pawel Garkusha
TUM School of Engineering and Design, Institute for Machine Tools and Industrial Management (iwb), Technical University of Munich , Boltzmannstrasse 15, Garching 85748
2 shared publications - Alena Gruendl
Technical University of Munich, TUM School of Engineering and Design, Department of Mechanical Engineering, Institute for Machine Tools and Industrial Management, Boltzmannstrasse 15, 85748 Garching, Germany
1 shared publication - Andreas Bachmann
Technical University of Munich (TUM)
1 shared publication
Latest Publications
- Open Access
- 20 October 2026
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 38 (4)
Influence of ultrashort-pulse laser-induced melt formation on the electrochemical performance of garnet-type solid electrolytes for solid-state batteries
Solid-state batteries promise higher safety and energy density than conventional lithium-ion batteries, positioning them as a key technology for next-generation energy storage systems. The garnet-type solid electrolyte lithium lanthanum zirconium oxide (LLZO) is among the most promising electrolytes for solid-state batteries. However, long-term operation requires a stable interface between the LLZO and the active materials, motivating targeted interfacial engineering. Ultrashort-pulsed laser ablation enables precise and flexible surface modification. However, it can also induce localized melting, increasing the risk of lithium loss and decomposition of the cubic LLZO phase, which is essential for high ionic conductivity. In this study, laser processing parameters were systematically varied to induce different regimes of melt formation on the LLZO surface, and the resulting effects on structure, interfacial stability, and mechanical integrity were investigated. Raman spectroscopy revealed that even pronounced laser-induced melting did not result in detectable phase changes within the bulk material. In symmetric lithium metal cells, an improved interfacial contact was observed for all laser-treated samples, while a pronounced increase in the critical current density occurred only for moderate melt residues compared to untreated reference samples. In contrast, excessive melting resulted in a reduced critical current density and diminished mechanical stability of the solid electrolyte. These findings highlight the existence of a processing regime in which controlled melt formation enhances the interfacial stability without compromising the structural integrity of the LLZO.
- 20 October 2026
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 38 (4)
Open AccessInfluence of ultrashort-pulse laser-induced melt formation on the electrochemical performance of garnet-type solid electrolytes for solid-state batteries
Solid-state batteries promise higher safety and energy density than conventional lithium-ion batteries, positioning them as a key technology for next-generation energy storage systems. The garnet-type solid electrolyte lithium lanthanum zirconium oxide (LLZO) is among the most promising electrolytes for solid-state batteries. However, long-term operation requires a stable interface between the LLZO and the active materials, motivating targeted interfacial engineering. Ultrashort-pulsed laser ablation enables precise and flexible surface modification. However, it can also induce localized melting, increasing the risk of lithium loss and decomposition of the cubic LLZO phase, which is essential for high ionic conductivity. In this study, laser processing parameters were systematically varied to induce different regimes of melt formation on the LLZO surface, and the resulting effects on structure, interfacial stability, and mechanical integrity were investigated. Raman spectroscopy revealed that even pronounced laser-induced melting did not result in detectable phase changes within the bulk material. In symmetric lithium metal cells, an improved interfacial contact was observed for all laser-treated samples, while a pronounced increase in the critical current density occurred only for moderate melt residues compared to untreated reference samples. In contrast, excessive melting resulted in a reduced critical current density and diminished mechanical stability of the solid electrolyte. These findings highlight the existence of a processing regime in which controlled melt formation enhances the interfacial stability without compromising the structural integrity of the LLZO.
- Open Access
- 3 December 2025
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 38 (1)
Optimizing the dynamic performance of galvanometric scanners through advanced trajectory planning for laser material processing
Galvanometric scanners constitute fundamental actuators in precision laser manufacturing, yet inertia-induced tracking errors impose severe throughput limitations for μm-scale positioning tasks. This work presents a software-based trajectory predistortion that compensates for scanner dynamics without hardware modification, enabling immediate deployment across existing industrial systems. Model-based trajectory optimization uses regularized inversion with Butterworth filtering to generate pre-compensated command signals that counteract inherent system lag. Experimental validation demonstrates settling time reductions of 49.2% for 30 μm movements and 17.3% for mm-scale movements. The tracking error decreased by precisely 50% from 200 to 100 μs, independent of the movement amplitude. Industrial implementation for titanium porous transport layer fabrication achieved 38.1% throughput enhancement. This software-only approach requires no hardware investment and integrates seamlessly with existing control systems. The methodology generalizes to diverse scanner-based applications, where positioning dynamics constrain manufacturing throughput. Widespread adoption could significantly accelerate production across multiple industries utilizing galvanometric scanning systems, as the technique can maximize the performance from installed equipment bases without hardware replacement or extended qualification procedures.
- 3 December 2025
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 38 (1)
Open AccessOptimizing the dynamic performance of galvanometric scanners through advanced trajectory planning for laser material processing
Galvanometric scanners constitute fundamental actuators in precision laser manufacturing, yet inertia-induced tracking errors impose severe throughput limitations for μm-scale positioning tasks. This work presents a software-based trajectory predistortion that compensates for scanner dynamics without hardware modification, enabling immediate deployment across existing industrial systems. Model-based trajectory optimization uses regularized inversion with Butterworth filtering to generate pre-compensated command signals that counteract inherent system lag. Experimental validation demonstrates settling time reductions of 49.2% for 30 μm movements and 17.3% for mm-scale movements. The tracking error decreased by precisely 50% from 200 to 100 μs, independent of the movement amplitude. Industrial implementation for titanium porous transport layer fabrication achieved 38.1% throughput enhancement. This software-only approach requires no hardware investment and integrates seamlessly with existing control systems. The methodology generalizes to diverse scanner-based applications, where positioning dynamics constrain manufacturing throughput. Widespread adoption could significantly accelerate production across multiple industries utilizing galvanometric scanning systems, as the technique can maximize the performance from installed equipment bases without hardware replacement or extended qualification procedures.
- Open Access
- 19 February 2024
- Published by Elsevier in Optics & Laser Technology
- Vol. 175
Analysis of photodiode signals for monitoring the laser beam welding process of cell-internal contacts in lithium-ion batteries
- 19 February 2024
- Published by Elsevier in Optics & Laser Technology
- Vol. 175
Open AccessAnalysis of photodiode signals for monitoring the laser beam welding process of cell-internal contacts in lithium-ion batteries
- Open Access
- 13 October 2022
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 34 (4) , 042017
Toward the flexible production of large-format lithium-ion batteries using laser-based cell-internal contacting
Lithium-ion battery cells are used for energy storage in many industrial sectors, such as consumer electronics or electromobility. Due to the diversity of these applications, the demand for tailored battery cells is increasing. Consequently, the technical development of the cells leads to numerous coexisting cell variants. Examples of such variants are altering cell materials, formats, and capacities. Different target capacities can be realized by changing the geometrical dimensions of the individual electrodes or the number of electrodes in the cell cores. The increasing quantity of variants poses challenges within battery cell manufacturing, such as the need to adapt the process parameters for the cell-internal contacting of a higher number of electrode sheets in the cell stack. Each new cell variant currently requires elaborate experimental parameter studies for its manufacture. An approach for selecting suitable process parameters for laser-based cell-internal contacting in terms of a modification of the cell properties is presented in this paper. A model was built to determine the weld depth in copper sheets using a millisecond pulsed laser welding strategy. The process parameters for welding stacks of electrode sheets to an arrester tab were calculated on the basis of this model. The necessary weld depth in the arrester tab for achieving suitable mechanical properties of the cell-internal joint was considered. The presented approach was validated by welding different numbers of foils to an arrester tab and varying the thickness of the foils. It was shown that the experimental effort for the selection of the process parameters for laser-based contacting can be reduced significantly.
- 13 October 2022
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 34 (4) , 042017
Open AccessToward the flexible production of large-format lithium-ion batteries using laser-based cell-internal contacting
Lithium-ion battery cells are used for energy storage in many industrial sectors, such as consumer electronics or electromobility. Due to the diversity of these applications, the demand for tailored battery cells is increasing. Consequently, the technical development of the cells leads to numerous coexisting cell variants. Examples of such variants are altering cell materials, formats, and capacities. Different target capacities can be realized by changing the geometrical dimensions of the individual electrodes or the number of electrodes in the cell cores. The increasing quantity of variants poses challenges within battery cell manufacturing, such as the need to adapt the process parameters for the cell-internal contacting of a higher number of electrode sheets in the cell stack. Each new cell variant currently requires elaborate experimental parameter studies for its manufacture. An approach for selecting suitable process parameters for laser-based cell-internal contacting in terms of a modification of the cell properties is presented in this paper. A model was built to determine the weld depth in copper sheets using a millisecond pulsed laser welding strategy. The process parameters for welding stacks of electrode sheets to an arrester tab were calculated on the basis of this model. The necessary weld depth in the arrester tab for achieving suitable mechanical properties of the cell-internal joint was considered. The presented approach was validated by welding different numbers of foils to an arrester tab and varying the thickness of the foils. It was shown that the experimental effort for the selection of the process parameters for laser-based contacting can be reduced significantly.
- Open Access
- 1 October 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 118 (7-8) , 2571-2586
Laser welding of current collector foil stacks in battery production–mechanical properties of joints welded with a green high-power disk laser
The qualification of production systems that enable reliable and stable production processes is a major challenge in manufacturing large-format lithium-ion batteries. During cell assembly, the electrode sheets of the anode and the cathode are stacked, and are electrically contacted by a welding process. It was shown that laser beam welding employing a beam source in the green wavelength range is a promising joining approach in terms of high productivity. Therefore, the influence of the process parameters, such as the laser power, the welding speed, the pulse frequency, and the pulse duration, on the weld seam quality was investigated. Particular emphasis was placed on the mechanical strength of the weld seam. Statistically planned experiments were used to determine feasible parameter sets for welding the most common current collectors of lithium-ion battery electrodes, copper (Cu), and aluminum (Al). The influence of the individual process parameters on the tensile shear force was evaluated. Stacks of 40 metal foils were welded with a thin metal sheet in lap joint configuration. Based on an analysis of the requirements for minimum mechanical seam strengths, this study confirms that laser beam welding using a green high-power disk source is an auspicious process for the internal contacting of lithium-ion batteries.
- 1 October 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 118 (7-8) , 2571-2586
Open AccessLaser welding of current collector foil stacks in battery production–mechanical properties of joints welded with a green high-power disk laser
The qualification of production systems that enable reliable and stable production processes is a major challenge in manufacturing large-format lithium-ion batteries. During cell assembly, the electrode sheets of the anode and the cathode are stacked, and are electrically contacted by a welding process. It was shown that laser beam welding employing a beam source in the green wavelength range is a promising joining approach in terms of high productivity. Therefore, the influence of the process parameters, such as the laser power, the welding speed, the pulse frequency, and the pulse duration, on the weld seam quality was investigated. Particular emphasis was placed on the mechanical strength of the weld seam. Statistically planned experiments were used to determine feasible parameter sets for welding the most common current collectors of lithium-ion battery electrodes, copper (Cu), and aluminum (Al). The influence of the individual process parameters on the tensile shear force was evaluated. Stacks of 40 metal foils were welded with a thin metal sheet in lap joint configuration. Based on an analysis of the requirements for minimum mechanical seam strengths, this study confirms that laser beam welding using a green high-power disk source is an auspicious process for the internal contacting of lithium-ion batteries.