Kalpana Sharma
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kalpana Sharma has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- David John Hunter
Faculty of Medicine and Health, Sydney Musculoskeletal Health, Kolling Institute, The University of Sydney, Sydney, Australia
1 shared publication Felix Eckstein
Department of Imaging & Functional Musculoskeletal Research, Institute of Anatomy & Cell Biology, Paracelsus Medical University Salzburg & Nuremberg, Salzburg, Austria
1 shared publication- Felix Eckstein
Research Group for Musculoskeletal Imaging, Center for Anatomy and Cell Biology and Ludwig Boltzmann Institute for Arthritis and Rehabilitation (LBIAR), Paracelsus Medical University, Salzburg, Austria; Chondrometrics GmbH, Freilassing, Germany
1 shared publication Katja Emmanuel
Department of Imaging & Functional Musculoskeletal Research, Institute of Anatomy & Cell Biology, Paracelsus Medical University Salzburg & Nuremberg, Salzburg, Austria
1 shared publication- Melanie Roth
Affiliation Department Health Sciences, Salzburg University of Applied Sciences, Puch/Salzburg, Austria
1 shared publication - Susanne Maschek
Chondrometrics GmbH, Freilassing, Germany
1 shared publication
Latest Publications
- Open Access
- 19 June 2025
- Published by Elsevier in Osteoarthritis Imaging
- Vol. 5 (3)
Quantitative meniscus imaging and analysis: A narrative review
- 19 June 2025
- Published by Elsevier in Osteoarthritis Imaging
- Vol. 5 (3)
Open AccessQuantitative meniscus imaging and analysis: A narrative review
- Open Access
- 25 July 2023
- Published by Elsevier in Osteoarthritis and Cartilage
- Vol. 31 (10) , 1396-1404
Association of quantitative measures of medial meniscal extrusion with structural and symptomatic knee osteoarthritis progression – Data from the OAI FNIH biomarker study
- 25 July 2023
- Published by Elsevier in Osteoarthritis and Cartilage
- Vol. 31 (10) , 1396-1404
Open AccessAssociation of quantitative measures of medial meniscal extrusion with structural and symptomatic knee osteoarthritis progression – Data from the OAI FNIH biomarker study
- Open Access
- 30 September 2021
- Published by Springer Nature in Skeletal Radiology
- Vol. 51 (5) , 997-1006
Meniscus position and size in knees with versus without structural knee osteoarthritis progression: data from the osteoarthritis initiative
Objective: To explore whether and which quantitative 3D measures of medial and/or lateral meniscus position and size are associated with subsequent medial femorotibial structural progression of knee osteoarthritis and to determine the correlation between central slice and total meniscus measures. Materials and Methods: Knees with radiographic osteoarthritis from Osteoarthritis Initiative participants with longitudinal medial MRI-based cartilage thickness and radiographic joint space width (JSW) loss over 12 months were selected. These 37 structural progressor knees (64.7 ± 8.0y, 30.2 ± 4.6 kg/m2, 35% men) were matched 1:1 to 37 non-progressor knees (64.6 ± 9.8y, 30.2 ± 4.4 kg/m2, 35% men) without cartilage thickness or JSW loss. Quantitative measures of meniscus position and size were computed from manual segmentations of coronal baseline MRIs. Cohen’s D was used as measure of effect size. Results: Maximum extrusion distance of the total medial meniscus and mean extrusion in the central 5 and in the central slice were greater for progressor than non-progressor knees (Cohen’s D 0.58–0.66). No significant differences were observed for medial tibial coverage or mean extrusion (entire meniscus). Among medial meniscus morphology measures, only mean height differed between progressor vs non-progressor knees (Cohen’s D 0.40). Among lateral meniscus measures, height and volume were greater in progressor vs. non-progressor knees (Cohen’s D 0.46–0.83). Mean extrusion measures were highly correlated between the entire meniscus and the central (r = 0.88) or the central 5 (r = 0.93) slices. Conclusions: 3D maximum and central medial meniscus extrusion may serve as predictors for subsequent structural progression. Central meniscus extrusion measures could substitute 3D extrusion measurement across the entire meniscus.
- 30 September 2021
- Published by Springer Nature in Skeletal Radiology
- Vol. 51 (5) , 997-1006
Open AccessMeniscus position and size in knees with versus without structural knee osteoarthritis progression: data from the osteoarthritis initiative
Objective: To explore whether and which quantitative 3D measures of medial and/or lateral meniscus position and size are associated with subsequent medial femorotibial structural progression of knee osteoarthritis and to determine the correlation between central slice and total meniscus measures. Materials and Methods: Knees with radiographic osteoarthritis from Osteoarthritis Initiative participants with longitudinal medial MRI-based cartilage thickness and radiographic joint space width (JSW) loss over 12 months were selected. These 37 structural progressor knees (64.7 ± 8.0y, 30.2 ± 4.6 kg/m2, 35% men) were matched 1:1 to 37 non-progressor knees (64.6 ± 9.8y, 30.2 ± 4.4 kg/m2, 35% men) without cartilage thickness or JSW loss. Quantitative measures of meniscus position and size were computed from manual segmentations of coronal baseline MRIs. Cohen’s D was used as measure of effect size. Results: Maximum extrusion distance of the total medial meniscus and mean extrusion in the central 5 and in the central slice were greater for progressor than non-progressor knees (Cohen’s D 0.58–0.66). No significant differences were observed for medial tibial coverage or mean extrusion (entire meniscus). Among medial meniscus morphology measures, only mean height differed between progressor vs non-progressor knees (Cohen’s D 0.40). Among lateral meniscus measures, height and volume were greater in progressor vs. non-progressor knees (Cohen’s D 0.46–0.83). Mean extrusion measures were highly correlated between the entire meniscus and the central (r = 0.88) or the central 5 (r = 0.93) slices. Conclusions: 3D maximum and central medial meniscus extrusion may serve as predictors for subsequent structural progression. Central meniscus extrusion measures could substitute 3D extrusion measurement across the entire meniscus.