Krzysztof Rokicki
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Krzysztof Rokicki has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Hubert Sar
Institute of Vehicles and Construction Machinery Engineering, Warsaw University of Technology, 84 Narbutta Str., 02-524 Warsaw, Poland
3 shared publications - Mateusz Brukalski
Institute of Vehicles and Construction Machinery Engineering, Warsaw University of Technology, 84 Narbutta Str., 02-524 Warsaw, Poland
3 shared publications - Andrzej Reński
Institute of Vehicles and Construction Machinery Engineering, Warsaw University of Technology, 84 Narbutta Str., 02-524 Warsaw, Poland
1 shared publication - Michal Abramowski
Institute of Vehicles and Construction Machinery Engineering, Warsaw University of Technology, 84 Narbutta Str., 02-524 Warsaw, Poland
1 shared publication - Piotr Fundowicz
Institute of Vehicles and Construction Machinery Engineering, Warsaw University of Technology, 84 Narbutta Str., 02-524 Warsaw, Poland
1 shared publication
Latest Publications
- Open Access
Determining Tyre Adhesion Characteristics Based on the Road Tests of Automobiles
The motion of automobiles significantly depends on the conditions of interaction between a tyre and a road surface. One of the most frequently used ways of presenting the conditions of cooperation between a tyre and a road surface is a characteristic showing a longitudinal adhesion coefficient as a function of a longitudinal slip of a tyre. One of the methods for determining tyre-to-road adhesion characteristics is to use a special trailer combined with a towing vehicle. This type of method is commonly used to determine adhesion characteristics for a braked wheel. This article presents a method for determining adhesion characteristics for a driven wheel based on the road tests of automobiles. For this purpose, vehicle wheel velocity signals from a vehicle CAN network and a vehicle velocity signal from a GPS receiver were used. The signals from the CAN network were recorded using a special measurement card and an application developed in LabVIEW environment. The application developed in LabVIEW also allowed for simultaneous recording of automobile velocity from the GPS receiver. In this paper, the courses of a wheel velocity, longitudinal acceleration of automobile, longitudinal slip of the front wheels in time domain, as well as the coefficient of tyre-to-road longitudinal adhesion as a function of the longitudinal slip of the wheel are presented.
Open AccessDetermining Tyre Adhesion Characteristics Based on the Road Tests of Automobiles
The motion of automobiles significantly depends on the conditions of interaction between a tyre and a road surface. One of the most frequently used ways of presenting the conditions of cooperation between a tyre and a road surface is a characteristic showing a longitudinal adhesion coefficient as a function of a longitudinal slip of a tyre. One of the methods for determining tyre-to-road adhesion characteristics is to use a special trailer combined with a towing vehicle. This type of method is commonly used to determine adhesion characteristics for a braked wheel. This article presents a method for determining adhesion characteristics for a driven wheel based on the road tests of automobiles. For this purpose, vehicle wheel velocity signals from a vehicle CAN network and a vehicle velocity signal from a GPS receiver were used. The signals from the CAN network were recorded using a special measurement card and an application developed in LabVIEW environment. The application developed in LabVIEW also allowed for simultaneous recording of automobile velocity from the GPS receiver. In this paper, the courses of a wheel velocity, longitudinal acceleration of automobile, longitudinal slip of the front wheels in time domain, as well as the coefficient of tyre-to-road longitudinal adhesion as a function of the longitudinal slip of the wheel are presented.
- Open Access
- 1 July 2021
- Published by University of Zilina in Communications - Scientific letters of the University of Zilina
- Vol. 23 (3) , B211-B218
Research on Curvilinear Motion of Automobile with the Application of On-Board Can Bus Data
Modelling of vehicle's motion is one of the solutions applied in the research of automotive safety. There is always a discussion which model should be used for computer simulation. Models with higher number of degrees of freedom require identi...
- 1 July 2021
- Published by University of Zilina in Communications - Scientific letters of the University of Zilina
- Vol. 23 (3) , B211-B218
Open AccessResearch on Curvilinear Motion of Automobile with the Application of On-Board Can Bus Data
Modelling of vehicle's motion is one of the solutions applied in the research of automotive safety. There is always a discussion which model should be used for computer simulation. Models with higher number of degrees of freedom require identi...
- Open Access
- 30 March 2020
- Published by Siec Badawcza Lukasiewicz - Przemyslowy Instytut Motoryzacji in The Archives of Automotive Engineering - Archiwum Motoryzacji
- Vol. 87 (1) , 19-32
Simulation of curvilinear motion of automobile with the use of two-degree-of-freedom flat model
Development of active safety systems of automobiles is nowadays based not only on road tests, but also on computer simulation of vehicle's curvilinear motion. To properly perform simulation, all required model parameters have to be properly estimated. The less complicated model is, the less parameters it requires. So that, it makes no sense to apply too complicated models, if we are not able to estimate parameters with relatively low error. One of the most popular is two- degree-of-freedom flat model to describe curvilinear motion of automobile. It is widely used in design and improvement of active safety systems. The article discusses the application of simple two- degree-of-freedom flat model of automobile, which requires only several parameters. These parameters are: mass of a vehicle, location of center of gravity of a vehicle, yaw mass moment of inertia of a vehicle, side-slip characteristics. Furthermore, to be able to compare simulation and measurement results, it is necessary to know some input signals such as steering wheel angle and velocity of a vehicle, recorded during road tests. In this article signal of steering wheel angle was taken from Controller Area Network (CAN) bus. In case of model of a vehicle, the Authors decided to compare the results of simulation using two different side slip characteristics known as the dependence between lateral reaction force and side slip angle: linear characteristic (constant cornering stiffness) and the characteristic represented by Pacejka’s Magic Formula in steady-state version.
- 30 March 2020
- Published by Siec Badawcza Lukasiewicz - Przemyslowy Instytut Motoryzacji in The Archives of Automotive Engineering - Archiwum Motoryzacji
- Vol. 87 (1) , 19-32
Open AccessSimulation of curvilinear motion of automobile with the use of two-degree-of-freedom flat model
Development of active safety systems of automobiles is nowadays based not only on road tests, but also on computer simulation of vehicle's curvilinear motion. To properly perform simulation, all required model parameters have to be properly estimated. The less complicated model is, the less parameters it requires. So that, it makes no sense to apply too complicated models, if we are not able to estimate parameters with relatively low error. One of the most popular is two- degree-of-freedom flat model to describe curvilinear motion of automobile. It is widely used in design and improvement of active safety systems. The article discusses the application of simple two- degree-of-freedom flat model of automobile, which requires only several parameters. These parameters are: mass of a vehicle, location of center of gravity of a vehicle, yaw mass moment of inertia of a vehicle, side-slip characteristics. Furthermore, to be able to compare simulation and measurement results, it is necessary to know some input signals such as steering wheel angle and velocity of a vehicle, recorded during road tests. In this article signal of steering wheel angle was taken from Controller Area Network (CAN) bus. In case of model of a vehicle, the Authors decided to compare the results of simulation using two different side slip characteristics known as the dependence between lateral reaction force and side slip angle: linear characteristic (constant cornering stiffness) and the characteristic represented by Pacejka’s Magic Formula in steady-state version.