Renzhou Zheng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Renzhou Zheng has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Jingbin Lu
College of Physics, Jilin University, Changchun, China
9 shared publications Xue Zhang
College of Physics, Jilin University 1 , Changchun 130012, China
9 shared publications- Yu Wang
College of Physics, Jilin University 1 , Changchun 130012, China
9 shared publications Ziyi Chen
College of Physics, Jilin University 1 , Changchun 130012, China
9 shared publicationsYumin Liu
College of Nuclear Science and Engineering, East China University of Technology 2 , Nanchang 330013, China
8 shared publicationsXiaoyi Li
College of Physics, Jilin University 1 , Changchun 130012, China
6 shared publications
Latest Publications
- Open Access
- 24 April 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 122 (17)
Theoretical prediction of time-related performance of GaN-based p–n junction betavoltaic battery
Betavoltaic batteries can meet long-term energy supply needs. However, due to the decay of the radioactive source, the output performance of battery will change over time, and the laws of this change require elucidation to aid the battery engineer. In this study, the influences of time on the apparent power density and β-energy spectrum of the 63 Ni source were clarified. Moreover, the structural parameters, including the p-region, n-region doping concentrations, and junction depth of GaN-based (hexagonal) p–n junction, were optimized, which are 2 × 1017 cm–3, 1014 cm–3, and 0.1 μm, respectively. In particular, the time-related performance trends were analyzed, and a formula for the maximum output power density deterioration was obtained, which can be used to evaluate the performance of 63 Ni GaN-based p–n junction betavoltaic battery within 200 years. The simulation results showed that the maximum output power density of battery after 50 years is 0.243 μW cm−2, which is only 60% of the initial value. In addition, the other output performances, namely, the short-circuit current density, open-circuit voltage, fill factor, and conversion efficiency are 0.096 μA cm−2, 2.67 V, 94.3%, and 20.5%, respectively.
- 24 April 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 122 (17)
Open AccessTheoretical prediction of time-related performance of GaN-based p–n junction betavoltaic battery
Betavoltaic batteries can meet long-term energy supply needs. However, due to the decay of the radioactive source, the output performance of battery will change over time, and the laws of this change require elucidation to aid the battery engineer. In this study, the influences of time on the apparent power density and β-energy spectrum of the 63 Ni source were clarified. Moreover, the structural parameters, including the p-region, n-region doping concentrations, and junction depth of GaN-based (hexagonal) p–n junction, were optimized, which are 2 × 1017 cm–3, 1014 cm–3, and 0.1 μm, respectively. In particular, the time-related performance trends were analyzed, and a formula for the maximum output power density deterioration was obtained, which can be used to evaluate the performance of 63 Ni GaN-based p–n junction betavoltaic battery within 200 years. The simulation results showed that the maximum output power density of battery after 50 years is 0.243 μW cm−2, which is only 60% of the initial value. In addition, the other output performances, namely, the short-circuit current density, open-circuit voltage, fill factor, and conversion efficiency are 0.096 μA cm−2, 2.67 V, 94.3%, and 20.5%, respectively.
- Open Access
- 1 October 2022
- Published by AIP Publishing in AIP Advances
- Vol. 12 (10) , 105302
Optimization design of 4H–SiC-based betavoltaic battery using 3H source
This paper describes the theoretical calculation and optimization design of the PN junction betavoltaic batteries with 4H–SiC-based energy converter and titanium tritide source. The self-absorption of radioactive isotope sources and the energy deposition distribution in the semiconductor converter are simulated using the Monte Carlo method. The relationship between doping concentrations and basic factors such as minority carrier diffusion lengths and the width of the depletion region are analyzed via the calculation formulas. Then the maximum output power density and energy conversion efficiency are calculated. The optimal thickness of the titanium tritide film is about 0.7 μm, the doping concentrations are 2.5 × 1016 cm−3, and the junction depth of PN junction is 0.1 μm. The surface recombination velocities of electron and hole are 1 × 106 cm/s, respectively. The maximum output power density and energy conversion efficiency are 0.22 μW/cm2 and 2.37%, respectively.
- 1 October 2022
- Published by AIP Publishing in AIP Advances
- Vol. 12 (10) , 105302
Open AccessOptimization design of 4H–SiC-based betavoltaic battery using 3H source
This paper describes the theoretical calculation and optimization design of the PN junction betavoltaic batteries with 4H–SiC-based energy converter and titanium tritide source. The self-absorption of radioactive isotope sources and the energy deposition distribution in the semiconductor converter are simulated using the Monte Carlo method. The relationship between doping concentrations and basic factors such as minority carrier diffusion lengths and the width of the depletion region are analyzed via the calculation formulas. Then the maximum output power density and energy conversion efficiency are calculated. The optimal thickness of the titanium tritide film is about 0.7 μm, the doping concentrations are 2.5 × 1016 cm−3, and the junction depth of PN junction is 0.1 μm. The surface recombination velocities of electron and hole are 1 × 106 cm/s, respectively. The maximum output power density and energy conversion efficiency are 0.22 μW/cm2 and 2.37%, respectively.
- 5 September 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 121 (10) , 103902
Understanding efficiency improvements of betavoltaic batteries based on 4H-SiC, GaN, and diamond
Wide-bandgap semiconductors are more advantageous for betavoltaic batteries due to their high conversion efficiency and strong radiation resistance. However, there has been little comprehensive analysis of how wide-bandgap semiconductors lead to efficiency improvements. In this work, we proposed a simulation model to predict the output performance of betavoltaic batteries based on 4H-SiC, hexagonal-GaN, and diamond, in which the Monte Carlo code and COMSOL Multiphysics software were combined. The energy deposition of a source in semiconductors and the electrical characteristics of p–n junctions were investigated and compared. Our simulation results showed that the mass density and atomic number of semiconductor materials will cause the difference in energy deposition distribution, further leading to the different electron–hole pair generation rates. Then, the internal efficiency of batteries is co-determined by the energy band structure, depletion region width, built-in potential barrier, and minority carrier lifetime. The batteries based on wide-bandgap semiconductors can achieve the larger open-circuit voltage, further leading to higher efficiency. Additionally, to optimize the energy converter structure, the output parameters were calculated with a variation of doping concentrations and thicknesses of each region. Under the irradiation of a source, the diamond-based battery with a p–n junction structure has the highest internal efficiency of 31.3%, while the GaN-based battery has the lowest one (16.8%), which can be attributed to the larger carrier recombination rate.- 5 September 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 121 (10) , 103902
Understanding efficiency improvements of betavoltaic batteries based on 4H-SiC, GaN, and diamond
Wide-bandgap semiconductors are more advantageous for betavoltaic batteries due to their high conversion efficiency and strong radiation resistance. However, there has been little comprehensive analysis of how wide-bandgap semiconductors lead to efficiency improvements. In this work, we proposed a simulation model to predict the output performance of betavoltaic batteries based on 4H-SiC, hexagonal-GaN, and diamond, in which the Monte Carlo code and COMSOL Multiphysics software were combined. The energy deposition of a source in semiconductors and the electrical characteristics of p–n junctions were investigated and compared. Our simulation results showed that the mass density and atomic number of semiconductor materials will cause the difference in energy deposition distribution, further leading to the different electron–hole pair generation rates. Then, the internal efficiency of batteries is co-determined by the energy band structure, depletion region width, built-in potential barrier, and minority carrier lifetime. The batteries based on wide-bandgap semiconductors can achieve the larger open-circuit voltage, further leading to higher efficiency. Additionally, to optimize the energy converter structure, the output parameters were calculated with a variation of doping concentrations and thicknesses of each region. Under the irradiation of a source, the diamond-based battery with a p–n junction structure has the highest internal efficiency of 31.3%, while the GaN-based battery has the lowest one (16.8%), which can be attributed to the larger carrier recombination rate.- 22 August 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 121 (8) , 083901
Theoretical prediction of output performance of 63NiO-Si heterojunction betavoltaic cell
For the 63NiO-Si heterojunction betavoltaic nuclear battery, the energy deposition of the energy conversion material itself was simulated by Monte Carlo simulation, and the structure of the 63NiO-Si heterojunction was optimized based on the theoretical calculation results. When the thickness of 63NiO is 4 μm and the doping concentration of Si is 1 × 1015 cm−3, the short-circuit current density, open-circuit voltage, fill factor, and maximum output power density of the nuclear battery are 1.22 μA · cm−2, 3.17 V, 0.95, 3.67 μW · cm−2. In addition, the output performance of 63Ni/NiO-Si heterojunction betavoltaic nuclear cell was calculated in this study. Under the condition that the activity of the radioactive source and the thickness of NiO(63NiO) are the same in the two structures, the proposed structure (63NiO-Si) has greatly improved the output performance of the nuclear battery by reducing the energy lost from radioactive source self-absorption.
- 22 August 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 121 (8) , 083901
Theoretical prediction of output performance of 63NiO-Si heterojunction betavoltaic cell
For the 63NiO-Si heterojunction betavoltaic nuclear battery, the energy deposition of the energy conversion material itself was simulated by Monte Carlo simulation, and the structure of the 63NiO-Si heterojunction was optimized based on the theoretical calculation results. When the thickness of 63NiO is 4 μm and the doping concentration of Si is 1 × 1015 cm−3, the short-circuit current density, open-circuit voltage, fill factor, and maximum output power density of the nuclear battery are 1.22 μA · cm−2, 3.17 V, 0.95, 3.67 μW · cm−2. In addition, the output performance of 63Ni/NiO-Si heterojunction betavoltaic nuclear cell was calculated in this study. Under the condition that the activity of the radioactive source and the thickness of NiO(63NiO) are the same in the two structures, the proposed structure (63NiO-Si) has greatly improved the output performance of the nuclear battery by reducing the energy lost from radioactive source self-absorption.
- Open Access
- 1 August 2022
- Published by AIP Publishing in AIP Advances
- Vol. 12 (8) , 085112
Modeling and optimization of GaN-based betavoltaic batteries: Comparison of p–n and p–i–n junctions
Nuclear battery is a promising long-life power source. Selecting semiconductors with high limit efficiency and appropriate device structures effectively improves their output performance. In this work, a GaN-based (hexagonal) betavoltaic battery with source was simulated by Monte Carlo codes and COMSOL Multiphysics, and the energy converters, including p–n junction and p–i–n junction, were compared and optimized. We analyzed the effects of thickness and doping concentration of each region on the battery performances. The p-region and n-region thickness and doping concentration of the p–n junction-based battery are 0.5, 9.5 µm, 1017 cm−3, and Nd = 1016 cm−3, which can achieve 3.77% conversion efficiency, and the short-circuit current density, open-circuit voltage, and maximum output power density are 0.074 µA/cm2, 2.01 V, and 0.125 µW/cm2, respectively. For the p–i–n junction-based battery, when the thickness and the doping concentration of p-region, i-region, and n-region are 0.5, 3, 6.5 µm, 1017, 1014, and 1016 cm−3, respectively, the conversion efficiency, short-circuit current density, open-circuit voltage, and maximum output power density are 5.03%, 0.099 µA/cm2, 2.0 V, and 0.167 µW/cm2, respectively. By comparing the output parameters of the two types of batteries, the results indicate that the p–i–n junction has a wider depletion region and better output performance compared with the p–n junction.- 1 August 2022
- Published by AIP Publishing in AIP Advances
- Vol. 12 (8) , 085112
Open AccessModeling and optimization of GaN-based betavoltaic batteries: Comparison of p–n and p–i–n junctions
Nuclear battery is a promising long-life power source. Selecting semiconductors with high limit efficiency and appropriate device structures effectively improves their output performance. In this work, a GaN-based (hexagonal) betavoltaic battery with source was simulated by Monte Carlo codes and COMSOL Multiphysics, and the energy converters, including p–n junction and p–i–n junction, were compared and optimized. We analyzed the effects of thickness and doping concentration of each region on the battery performances. The p-region and n-region thickness and doping concentration of the p–n junction-based battery are 0.5, 9.5 µm, 1017 cm−3, and Nd = 1016 cm−3, which can achieve 3.77% conversion efficiency, and the short-circuit current density, open-circuit voltage, and maximum output power density are 0.074 µA/cm2, 2.01 V, and 0.125 µW/cm2, respectively. For the p–i–n junction-based battery, when the thickness and the doping concentration of p-region, i-region, and n-region are 0.5, 3, 6.5 µm, 1017, 1014, and 1016 cm−3, respectively, the conversion efficiency, short-circuit current density, open-circuit voltage, and maximum output power density are 5.03%, 0.099 µA/cm2, 2.0 V, and 0.167 µW/cm2, respectively. By comparing the output parameters of the two types of batteries, the results indicate that the p–i–n junction has a wider depletion region and better output performance compared with the p–n junction. - 13 May 2022
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 55 (30) , 304002
Enhanced performance of GaAs-based betavoltaic batteries by using AlGaAs hole/electron transport layers
The GaAs-based betavoltaic batteries with 63 Ni source were demonstrated, in which the AlGaAs hole/electron transport layers were introduced to enhance the transport and collection of radiation-induced carriers. The Monte Carlo codes and COMSOL Multiphysics were combined to predict the output performance of batteries and optimize the structure parameters of energy converter. And the optimized GaAs-based battery with a 6 mCi cm−2 63 Ni source was expected to achieve a short-circuit current density (J sc ) of 85.6 nA cm−2, an open-circuit voltage (V oc ) of 0.67 V and a maximum output power density (P m ) of 43.3 nW cm−2. Then the GaAs/AlGaAs films were grown by metal organic chemical vapor deposition, and the comb-like electrodes were designed to reduce the absorption loss of beta particles in the p-plane electrode. The photoluminescence and x-ray diffraction were carried out to characterize the growth quality of epitaxial materials. The experimental results showed that the largest J sc of 9.3 nA cm−2, V oc of 55 mV and P m of 143.9 pW cm−2 can be achieved on the 2-busbar electrode battery. And the temperature dependence tests showed that when the temperature decreased to 233.15 K, the V oc and P m increased to 208 mV and 570.5 pW cm−2, respectively. Further improvements in fabrication process are needed to reduce the gap between experiment and prediction. In addition, the optimized structure of energy converter suggests the directions for enhancing the performance of betavoltaic batteries.
- 13 May 2022
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 55 (30) , 304002
Enhanced performance of GaAs-based betavoltaic batteries by using AlGaAs hole/electron transport layers
The GaAs-based betavoltaic batteries with 63 Ni source were demonstrated, in which the AlGaAs hole/electron transport layers were introduced to enhance the transport and collection of radiation-induced carriers. The Monte Carlo codes and COMSOL Multiphysics were combined to predict the output performance of batteries and optimize the structure parameters of energy converter. And the optimized GaAs-based battery with a 6 mCi cm−2 63 Ni source was expected to achieve a short-circuit current density (J sc ) of 85.6 nA cm−2, an open-circuit voltage (V oc ) of 0.67 V and a maximum output power density (P m ) of 43.3 nW cm−2. Then the GaAs/AlGaAs films were grown by metal organic chemical vapor deposition, and the comb-like electrodes were designed to reduce the absorption loss of beta particles in the p-plane electrode. The photoluminescence and x-ray diffraction were carried out to characterize the growth quality of epitaxial materials. The experimental results showed that the largest J sc of 9.3 nA cm−2, V oc of 55 mV and P m of 143.9 pW cm−2 can be achieved on the 2-busbar electrode battery. And the temperature dependence tests showed that when the temperature decreased to 233.15 K, the V oc and P m increased to 208 mV and 570.5 pW cm−2, respectively. Further improvements in fabrication process are needed to reduce the gap between experiment and prediction. In addition, the optimized structure of energy converter suggests the directions for enhancing the performance of betavoltaic batteries.
- Open Access
- 1 May 2022
- Published by AIP Publishing in AIP Advances
- Vol. 12 (5) , 055216
A method for improving the betavoltaic cell’s conversion efficiency: Using the alloy as Schottky metal
Under the irradiation of a 63Ni source, the Al/diamond Schottky barrier diode and 2198 Al–Li alloy/diamond Schottky barrier diode can convert decay energy into electrical energy. Through the Monte Carlo method, the energy depositions of the 63Ni source in the energy converters are simulated separately. And then the electrical output properties of two betavoltaic batteries are calculated and compared. The short-circuit current density, open-circuit voltage, fill factor and maximum output power density of the Al/diamond and 2198 Al–Li alloy/diamond Schottky barrier batteries are 0.086 μA/cm2, 2.14 V, 0.93, 0.17 μW/cm2 and 0.089 μA/cm2, 2.66 V, 0.95, 0.22 μW/cm2, respectively. The maximum output power increased by about 29%, which indicates that using alloy as Schottky metal can significantly improve the output performance of a betavoltaic battery.
- 1 May 2022
- Published by AIP Publishing in AIP Advances
- Vol. 12 (5) , 055216
Open AccessA method for improving the betavoltaic cell’s conversion efficiency: Using the alloy as Schottky metal
Under the irradiation of a 63Ni source, the Al/diamond Schottky barrier diode and 2198 Al–Li alloy/diamond Schottky barrier diode can convert decay energy into electrical energy. Through the Monte Carlo method, the energy depositions of the 63Ni source in the energy converters are simulated separately. And then the electrical output properties of two betavoltaic batteries are calculated and compared. The short-circuit current density, open-circuit voltage, fill factor and maximum output power density of the Al/diamond and 2198 Al–Li alloy/diamond Schottky barrier batteries are 0.086 μA/cm2, 2.14 V, 0.93, 0.17 μW/cm2 and 0.089 μA/cm2, 2.66 V, 0.95, 0.22 μW/cm2, respectively. The maximum output power increased by about 29%, which indicates that using alloy as Schottky metal can significantly improve the output performance of a betavoltaic battery.
- 16 February 2022
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 55 (19) , 194003
Optimization design of GaAs-based betavoltaic batteries with p–n junction and Schottky barrier structures
This paper presents the calculation model and the optimization design of the GaAs-based betavoltaic batteries with p–n junction and Schottky barrier structures. First of all, by using the Monte Carlo code, the transport process and energy deposition distribution of the 63 Ni source beta particles in the GaAs material are simulated. The relationships between the output parameters of batteries and the physical parameters of energy converter such as p–n junction depth, Schottky metal thickness, depletion region width and doping concentrations are discussed through the numerical calculation. For the GaAs p–n junction battery, the maximum output power density of 0.135 μ W cm − 2 can be achieved when the junction depth is x j = 0.05 μ m , the doping concentrations are N a = 10 18 cm − 3 and N d = 2 × 10 15 cm − 3 . Meanwhile, the short-circuit current density, open-circuit voltage, filling factor and energy conversion efficiency are 0.254 μ A cm − 2 , 0.638 V, 83.3% and 2.63%, respectively. Among the selected metals of Au, Pd, Ni and Pt for the GaAs Schottky barrier diodes, the Pt-GaAs battery has the best output performance due to its large work function. The maximum output power density of 0.169 μ W cm − 2 can be achieved when a 20 nm thick Schottky metal Pt is selected and the doping concentration is N d = 10 15 cm − 3 . The associated output parameters of the battery are 0.234 μ A cm − 2 , 0.835 V, 86.5% and 3.29%, respectively.
- 16 February 2022
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 55 (19) , 194003
Optimization design of GaAs-based betavoltaic batteries with p–n junction and Schottky barrier structures
This paper presents the calculation model and the optimization design of the GaAs-based betavoltaic batteries with p–n junction and Schottky barrier structures. First of all, by using the Monte Carlo code, the transport process and energy deposition distribution of the 63 Ni source beta particles in the GaAs material are simulated. The relationships between the output parameters of batteries and the physical parameters of energy converter such as p–n junction depth, Schottky metal thickness, depletion region width and doping concentrations are discussed through the numerical calculation. For the GaAs p–n junction battery, the maximum output power density of 0.135 μ W cm − 2 can be achieved when the junction depth is x j = 0.05 μ m , the doping concentrations are N a = 10 18 cm − 3 and N d = 2 × 10 15 cm − 3 . Meanwhile, the short-circuit current density, open-circuit voltage, filling factor and energy conversion efficiency are 0.254 μ A cm − 2 , 0.638 V, 83.3% and 2.63%, respectively. Among the selected metals of Au, Pd, Ni and Pt for the GaAs Schottky barrier diodes, the Pt-GaAs battery has the best output performance due to its large work function. The maximum output power density of 0.169 μ W cm − 2 can be achieved when a 20 nm thick Schottky metal Pt is selected and the doping concentration is N d = 10 15 cm − 3 . The associated output parameters of the battery are 0.234 μ A cm − 2 , 0.835 V, 86.5% and 3.29%, respectively.
- Open Access
- 1 October 2021
- Published by AIP Publishing in AIP Advances
- Vol. 11 (10) , 105108
Investigation of carrier transport and collection characteristics for GaAs-based betavoltaic batteries
This paper presents a simulation model to predict the performance of GaAs-based betavoltaic batteries with a p–n junction structure, in which the carrier transport and collection characteristics were studied. First, the electron–hole pair generation rate in the GaAs material under the irradiation of a 63Ni source was calculated using the Monte Carlo codes. Furthermore, by simulating the energy band structure, electric field distribution, and current density distribution in batteries with the finite element analysis software COMSOL Multiphysics, we analyzed the effects of structure parameters on the output performance. Our simulation results showed that the short-circuit current density (Jsc), open-circuit voltage (Voc), maximum output power density (Pm), and energy conversion efficiency (η) of the batteries are significantly affected by the thicknesses and doping concentrations of the p-region and n-region (Hp-GaAs, Hn-GaAs, Na, and Nd). The optimized GaAs-based battery with an Hp-GaAs value of 0.1 μm, an Hn-GaAs value of 9.9 μm, an Na value of 3.98 × 1016 cm−3, and an Nd value of 1 × 1015 cm−3 can achieve a Pm value of 0.080 μW/cm2. The related Jsc, Voc, and η values are 0.234 μA/cm2, 0.49 V, and 1.55%, respectively. When the top and bottom heavily doped layers are introduced, the Pm value of the battery is enhanced by 7.5% compared to that of the battery without heavily doped layers due to the formed drift fields.
- 1 October 2021
- Published by AIP Publishing in AIP Advances
- Vol. 11 (10) , 105108
Open AccessInvestigation of carrier transport and collection characteristics for GaAs-based betavoltaic batteries
This paper presents a simulation model to predict the performance of GaAs-based betavoltaic batteries with a p–n junction structure, in which the carrier transport and collection characteristics were studied. First, the electron–hole pair generation rate in the GaAs material under the irradiation of a 63Ni source was calculated using the Monte Carlo codes. Furthermore, by simulating the energy band structure, electric field distribution, and current density distribution in batteries with the finite element analysis software COMSOL Multiphysics, we analyzed the effects of structure parameters on the output performance. Our simulation results showed that the short-circuit current density (Jsc), open-circuit voltage (Voc), maximum output power density (Pm), and energy conversion efficiency (η) of the batteries are significantly affected by the thicknesses and doping concentrations of the p-region and n-region (Hp-GaAs, Hn-GaAs, Na, and Nd). The optimized GaAs-based battery with an Hp-GaAs value of 0.1 μm, an Hn-GaAs value of 9.9 μm, an Na value of 3.98 × 1016 cm−3, and an Nd value of 1 × 1015 cm−3 can achieve a Pm value of 0.080 μW/cm2. The related Jsc, Voc, and η values are 0.234 μA/cm2, 0.49 V, and 1.55%, respectively. When the top and bottom heavily doped layers are introduced, the Pm value of the battery is enhanced by 7.5% compared to that of the battery without heavily doped layers due to the formed drift fields.