Riley L. Howard
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Riley L. Howard has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Nancy L. Allbritton
Department of Bioengineering, University of Washington 1 , Seattle, Washington 98195
2 shared publications - Daniel M. Harris
Brown University
1 shared publication - Emma Abele
School of Engineering, Brown University, Providence, RI 02912, USA
1 shared publication - Francesca Bernardi
Worcester Polytechnic Institute
1 shared publication - Matthew Leff
Department of Applied Physical Sciences, University of North Carolina at Chapel Hill, Chapel Hill, NC 27599, USA
1 shared publication Yuli Wang
Department of Bioengineering, University of Washington, Seattle, Washington
1 shared publication
Latest Publications
- Open Access
- 4 November 2021
- Published by MDPI AG in Micromachines
- Vol. 12 (11) , 1360
Passive Control of Silane Diffusion for Gradient Application of Surface Properties
Liquid lithography represents a robust technique for fabricating three-dimensional (3D) microstructures on a two-dimensional template. Silanization of a surface is often a key step in the liquid lithography process and is used to alter the surface energy of the substrate and, consequently, the shape of the 3D microfeatures produced. In this work, we present a passive technique that allows for the generation of silane gradients along the length of a substrate. The technique relies on a secondary diffusion chamber with a single opening, leading to a directional introduction of silane to the substrate via passive diffusion. The secondary chamber geometry influences the deposited gradient, which is shown to be well captured by Monte Carlo simulations that incorporate the passive diffusion and grafting processes. The technique ultimately allows the user to generate a range of substrate wettabilities on a single chip, enhancing throughput for organ-on-a-chip applications by mimicking the spatial variability of tissue topographies present in vivo.
- 4 November 2021
- Published by MDPI AG in Micromachines
- Vol. 12 (11) , 1360
Open AccessPassive Control of Silane Diffusion for Gradient Application of Surface Properties
Liquid lithography represents a robust technique for fabricating three-dimensional (3D) microstructures on a two-dimensional template. Silanization of a surface is often a key step in the liquid lithography process and is used to alter the surface energy of the substrate and, consequently, the shape of the 3D microfeatures produced. In this work, we present a passive technique that allows for the generation of silane gradients along the length of a substrate. The technique relies on a secondary diffusion chamber with a single opening, leading to a directional introduction of silane to the substrate via passive diffusion. The secondary chamber geometry influences the deposited gradient, which is shown to be well captured by Monte Carlo simulations that incorporate the passive diffusion and grafting processes. The technique ultimately allows the user to generate a range of substrate wettabilities on a single chip, enhancing throughput for organ-on-a-chip applications by mimicking the spatial variability of tissue topographies present in vivo.
- 26 October 2021
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 31 (12) , 125006
Use of liquid lithography to form in vitro intestinal crypts with varying microcurvature surrounding the stem cell niche
Objective. The role of the crypt microarchitecture and surrounding tissue curvature on intestinal stem/proliferative cell physiology is unknown. The utility of liquid lithography in creating polydimethylsiloxane (PDMS) micropillar stamps with controlled tip curvature was assessed. Using these stamps, the impact of microcurvature at the crypt base on intestinal cell and cytoskeletal behavior was studied. Approach . An SU-8 master mold as a support, polyols of varying surface energies as sacrificial liquids, and liquid PDMS as the solidifiable material were combined using liquid lithography to form PDMS micropillar arrays. Vapor phase deposition of organosilane onto the master mold was used to modify the surface energy of the master mold to shape the micropillar tips. Collagen was molded using the micropillar arrays forming a scaffold for culture of human primary colonic epithelial cells. Cell proliferation and cytoskeletal properties were assessed using fluorescent stains. Main results . Liquid lithography using low surface energy polyols (55 dynes cm −1 ) yielded concave-tipped PDMS micropillars. Gradients of octyltrichlorosilane deposition across a master mold with an array of microwells yielded a PDMS micropillar array with a range of tip curvatures. Human primary colonic epithelial cells cultured on micropillar-molded collagen scaffolds demonstrated a stem/proliferative cell compartment at the crypt base. Crypts with a convex base demonstrated significantly lower cell proliferation at the crypt base than that of cells in crypts with either flat or concave bases. Crypts with a convex base also displayed higher levels of G-actin activity compared to that of crypts with flat or concave bases. Significance . Liquid lithography enabled creation of arrays of in vitro colonic crypts with programmable curvature. Primary cells at the crypt base sensed and responded to surface curvature by altering their proliferation and cytoskeletal properties.
- 26 October 2021
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 31 (12) , 125006
Use of liquid lithography to form in vitro intestinal crypts with varying microcurvature surrounding the stem cell niche
Objective. The role of the crypt microarchitecture and surrounding tissue curvature on intestinal stem/proliferative cell physiology is unknown. The utility of liquid lithography in creating polydimethylsiloxane (PDMS) micropillar stamps with controlled tip curvature was assessed. Using these stamps, the impact of microcurvature at the crypt base on intestinal cell and cytoskeletal behavior was studied. Approach . An SU-8 master mold as a support, polyols of varying surface energies as sacrificial liquids, and liquid PDMS as the solidifiable material were combined using liquid lithography to form PDMS micropillar arrays. Vapor phase deposition of organosilane onto the master mold was used to modify the surface energy of the master mold to shape the micropillar tips. Collagen was molded using the micropillar arrays forming a scaffold for culture of human primary colonic epithelial cells. Cell proliferation and cytoskeletal properties were assessed using fluorescent stains. Main results . Liquid lithography using low surface energy polyols (55 dynes cm −1 ) yielded concave-tipped PDMS micropillars. Gradients of octyltrichlorosilane deposition across a master mold with an array of microwells yielded a PDMS micropillar array with a range of tip curvatures. Human primary colonic epithelial cells cultured on micropillar-molded collagen scaffolds demonstrated a stem/proliferative cell compartment at the crypt base. Crypts with a convex base demonstrated significantly lower cell proliferation at the crypt base than that of cells in crypts with either flat or concave bases. Crypts with a convex base also displayed higher levels of G-actin activity compared to that of crypts with flat or concave bases. Significance . Liquid lithography enabled creation of arrays of in vitro colonic crypts with programmable curvature. Primary cells at the crypt base sensed and responded to surface curvature by altering their proliferation and cytoskeletal properties.