Ngie Hing Wong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Ngie Hing Wong has a total of 121 co-authors. Here are the top co-authors by number of shared publications:
- Jaka Sunarso
Research Centre for Sustainable Technologies, Faculty of Engineering, Computing and Science Swinburne University of Technology Kuching Sarawak Malaysia
16 shared publications Jaka Sunarso
Research Centre for Sustainable Technologies, Faculty of Engineering, Computing and Science, Swinburne University of Technology, Kuching, Malaysia
4 shared publicationsShaomin Liu
4 shared publicationsSongchen Xie
4 shared publicationsDan Guo
3 shared publicationsGuihua Chen
3 shared publications
Latest Publications
- Open Access
- 29 July 2026
- Published by Wiley in Water Environment Research
- Vol. 98 (8)
Elucidation of the Physical Separation and Accumulation Mechanisms of Three Distinct Layers in Grease Traps
Grease traps are essential for intercepting fats, oils, and grease (FOG) to prevent sewer blockages. However, the internal mechanisms governing their separation efficiency and layer accumulation remain poorly defined. This work investigates the dynamics of three distinct internal phases inside grease traps, i.e., top‐floated scum, middle‐clarified liquid, and bottom‐settled sludge, through a 32‐day site investigation (SI) and 24 laboratory column tests (CTs). The SI revealed that the settled sludge layer was 10 times thicker at the inlet chamber and 72 times thicker at the outlet chamber than the floated scum, indicating that sludge accumulation is the primary driver of desludging frequency and a key indirect influence on grease trap performance. CT results further demonstrated that separation kinetics were governed by solids content, with low‐solid wastewater achieving settling velocities of up to 3.04 m h −1 , significantly higher than those of high‐solid wastewater (0.87 m h −1 ). These differences highlight the solid content in the grease trap governing the separation rates. Based on these findings, this work proposes optimized design criteria, including a surface overflow rate (SOR) of 20.9 m 3 d −1 m −2 , a minimum surface area ( A s ) of 1.25 m 2 , and a 1‐h hydraulic retention time (HRT). Ultimately, these results provide a systematic assessment framework to refine grease‐trap design standards based on the physical behavior of all three internal waste layers.
- 29 July 2026
- Published by Wiley in Water Environment Research
- Vol. 98 (8)
Open AccessElucidation of the Physical Separation and Accumulation Mechanisms of Three Distinct Layers in Grease Traps
Grease traps are essential for intercepting fats, oils, and grease (FOG) to prevent sewer blockages. However, the internal mechanisms governing their separation efficiency and layer accumulation remain poorly defined. This work investigates the dynamics of three distinct internal phases inside grease traps, i.e., top‐floated scum, middle‐clarified liquid, and bottom‐settled sludge, through a 32‐day site investigation (SI) and 24 laboratory column tests (CTs). The SI revealed that the settled sludge layer was 10 times thicker at the inlet chamber and 72 times thicker at the outlet chamber than the floated scum, indicating that sludge accumulation is the primary driver of desludging frequency and a key indirect influence on grease trap performance. CT results further demonstrated that separation kinetics were governed by solids content, with low‐solid wastewater achieving settling velocities of up to 3.04 m h −1 , significantly higher than those of high‐solid wastewater (0.87 m h −1 ). These differences highlight the solid content in the grease trap governing the separation rates. Based on these findings, this work proposes optimized design criteria, including a surface overflow rate (SOR) of 20.9 m 3 d −1 m −2 , a minimum surface area ( A s ) of 1.25 m 2 , and a 1‐h hydraulic retention time (HRT). Ultimately, these results provide a systematic assessment framework to refine grease‐trap design standards based on the physical behavior of all three internal waste layers.
- 7 March 2026
- Published by Elsevier in Applied Surface Science
- Vol. 732
Durable and highly efficient heterojunction BiOI/BiVO4/PAN nanofibers for visible light driven pollutant remediation
- 7 March 2026
- Published by Elsevier in Applied Surface Science
- Vol. 732
Durable and highly efficient heterojunction BiOI/BiVO4/PAN nanofibers for visible light driven pollutant remediation
- 26 July 2025
- Published by Elsevier in Applied Surface Science
- Vol. 712
Hydrosol-enhanced hydrophilicity in La3+-filtrated layered double hydroxides membrane for efficient removal of phosphate
- 26 July 2025
- Published by Elsevier in Applied Surface Science
- Vol. 712
Hydrosol-enhanced hydrophilicity in La3+-filtrated layered double hydroxides membrane for efficient removal of phosphate
- Open Access
- 3 June 2024
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 41 (4) , 1891-1907
Physicochemical Characteristics of Silicomanganese Slag as a Recycling Construction Material: An Overview
Silicomanganese (SiMn) slag is a by-product of ferromanganese and SiMn alloy production poses significant challenges in terms of environmentally sound disposal given its substantial volume. This brief review aims to assess the physicochemical attributes of SiMn slag and explore its potential applications in construction materials recycling. To accomplish this, we systematically evaluated 20 relevant articles, categorizing them into segments covering reutilization methods, key considerations, enhancement strategies, and the recent challenges and prospects associated with SiMn slag reutilization. Our analysis encompassed SiMn slags from five countries, revealing consistent chemical compositions characterized by SiO2, Al2O3, CaO, MnO, MgO, FeO + Fe2O3, and K2O + Na2O at similar proportions. We identified two distinct types of SiMn slag, i.e., air-cooled and water-quenched, each possessing unique physical properties influencing their suitability for reutilization. SiMn slag has been successfully repurposed into various construction materials, including cement paste, mortar, concrete, alkali-activated matrices, bricks, backfill materials, Mn extracts, and binder/cement. Several critical factors must be considered when reutilizing SiMn slag in construction materials, including cooling methods, moisture content, particle size (fineness), equipment, energy requirements, and cost considerations. To enhance the reutilization process, we propose a structured approach consisting of four key steps, i.e., incoming waste assessment, pre-treatment, physical/chemical treatment, and product development. Furthermore, this review suggests several avenues for future research, including the development of industrial-scale recycling applications, exploring environmentally friendly landfilling methods for SiMn slag, and assessing the practicality and feasibility of SiMn-slag-based products in real-world construction projects.
- 3 June 2024
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 41 (4) , 1891-1907
Open AccessPhysicochemical Characteristics of Silicomanganese Slag as a Recycling Construction Material: An Overview
Silicomanganese (SiMn) slag is a by-product of ferromanganese and SiMn alloy production poses significant challenges in terms of environmentally sound disposal given its substantial volume. This brief review aims to assess the physicochemical attributes of SiMn slag and explore its potential applications in construction materials recycling. To accomplish this, we systematically evaluated 20 relevant articles, categorizing them into segments covering reutilization methods, key considerations, enhancement strategies, and the recent challenges and prospects associated with SiMn slag reutilization. Our analysis encompassed SiMn slags from five countries, revealing consistent chemical compositions characterized by SiO2, Al2O3, CaO, MnO, MgO, FeO + Fe2O3, and K2O + Na2O at similar proportions. We identified two distinct types of SiMn slag, i.e., air-cooled and water-quenched, each possessing unique physical properties influencing their suitability for reutilization. SiMn slag has been successfully repurposed into various construction materials, including cement paste, mortar, concrete, alkali-activated matrices, bricks, backfill materials, Mn extracts, and binder/cement. Several critical factors must be considered when reutilizing SiMn slag in construction materials, including cooling methods, moisture content, particle size (fineness), equipment, energy requirements, and cost considerations. To enhance the reutilization process, we propose a structured approach consisting of four key steps, i.e., incoming waste assessment, pre-treatment, physical/chemical treatment, and product development. Furthermore, this review suggests several avenues for future research, including the development of industrial-scale recycling applications, exploring environmentally friendly landfilling methods for SiMn slag, and assessing the practicality and feasibility of SiMn-slag-based products in real-world construction projects.
- Open Access
- 11 April 2024
- Published by Elsevier in Water Research
- Vol. 256, 121607
Physicochemical characteristics of grease-trap wastewater with different potential mechanisms of FOG solid formation, separation, and accumulation inside grease traps
- 11 April 2024
- Published by Elsevier in Water Research
- Vol. 256, 121607
Open AccessPhysicochemical characteristics of grease-trap wastewater with different potential mechanisms of FOG solid formation, separation, and accumulation inside grease traps
- 4 January 2024
- Published by Elsevier in Chemosphere
- Vol. 350, 141103
Fabricating an adsorbent and micro-nano bubble catalyst through confining maghemite in the β cage of NaY zeolite
- 4 January 2024
- Published by Elsevier in Chemosphere
- Vol. 350, 141103
Fabricating an adsorbent and micro-nano bubble catalyst through confining maghemite in the β cage of NaY zeolite
- Open Access
- 20 December 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 42 (1)
Enhanced antifouling and antibacterial performances on polytetrafluoroethylene microporous membranes sputtered with silver nanoparticles
A bare polytetrafluoroethylene (PTFE) membrane has poor antifouling and antibacterial performance in the application process. In this work, the silver nanoparticle layer (AgNP-layer) was deposited onto the PTFE membrane surface via the magnetron sputtering process to overcome these limitations. Several spectra and microscopic analyses were taken to characterize the synthesized PTFE/AgNP-layer composite membranes. The effects of magnetron sputtering time on the AgNP-layer distribution, microstructure, antifouling, and antibacterial properties were systematically investigated. Our results showed the successful deposition and grafting of the AgNP-layer on the PTFE membrane surface and inside the cross-sectional pores near the membrane surface. The AgNP-layer not only improved the composite membrane wettability but also reduced its protein adsorption capacity from 88 to 39 μg, thus improving the antifouling ability of the membrane. The composite membranes could also achieve 99% and 88% antibacterial rates against Escherichia coli and Staphylococcus aureus, respectively, exhibiting good antibacterial activity.
- 20 December 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 42 (1)
Open AccessEnhanced antifouling and antibacterial performances on polytetrafluoroethylene microporous membranes sputtered with silver nanoparticles
A bare polytetrafluoroethylene (PTFE) membrane has poor antifouling and antibacterial performance in the application process. In this work, the silver nanoparticle layer (AgNP-layer) was deposited onto the PTFE membrane surface via the magnetron sputtering process to overcome these limitations. Several spectra and microscopic analyses were taken to characterize the synthesized PTFE/AgNP-layer composite membranes. The effects of magnetron sputtering time on the AgNP-layer distribution, microstructure, antifouling, and antibacterial properties were systematically investigated. Our results showed the successful deposition and grafting of the AgNP-layer on the PTFE membrane surface and inside the cross-sectional pores near the membrane surface. The AgNP-layer not only improved the composite membrane wettability but also reduced its protein adsorption capacity from 88 to 39 μg, thus improving the antifouling ability of the membrane. The composite membranes could also achieve 99% and 88% antibacterial rates against Escherichia coli and Staphylococcus aureus, respectively, exhibiting good antibacterial activity.