Xubo Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Xubo Zhang has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
Minger Wu
4 shared publications- Han Bao
The Third Construction Co., Ltd. of China Construction Eighth Engineering Division, Nanjing 210046, China
2 shared publications Yiyi Zhou
2 shared publicationsYue Li
2 shared publicationsFeng Liu
1 shared publicationHan Bao
Department of Structural Engineering, College of Civil Engineering, Tongji University, Tongji University, China
1 shared publication
Latest Publications
- 24 January 2024
- Published by Elsevier in Construction and Building Materials
- Vol. 415
Fracture toughness of coated fabric with nonlinear tensile behaviors considered- 24 January 2024
- Published by Elsevier in Construction and Building Materials
- Vol. 415
Fracture toughness of coated fabric with nonlinear tensile behaviors considered- 10 December 2022
- Published by Elsevier in Thin-Walled Structures
- Vol. 183
Tearing behaviors of coated fabric membrane structures
- 10 December 2022
- Published by Elsevier in Thin-Walled Structures
- Vol. 183
Tearing behaviors of coated fabric membrane structures
- 1 June 2022
- Published by SAGE Publications in Journal of Industrial Textiles
- Vol. 51 (4_suppl) , 5560S-5591S
Modified stress field model for critical tearing strength of architectural coated fabrics
This report presents a new critical tearing strength prediction model, the modified stress field model. Firstly, the critical tearing strength of six coated fabrics is obtained using the single-edge notched tests. The results show that the warp and weft strength utilization of different coated fabrics is similar. Based on the test data, the prediction effects, parameter meanings, and basic properties of three models, namely Thiele’s empirical formula, the stress field model, and the modified stress field model, are discussed and compared. Then, the predicted results and properties of the three models in different crack ranges, specifically the small crack range, are compared, and their application scopes are verified. The two commonly used models lack the improved prediction effects in the small crack range that is provided by the modified stress field model. Finally, to reduce the workload while maintaining a certain accuracy, a crack combination of 3 mm + 15 mm is recommended, which is further confirmed using the root-mean-square error index. The prediction results of Thiele’s empirical formula and the modified stress field model under this crack combination are compared. The new model can still maintain good prediction effects even when extrapolating for small cracks using limited test data. Because of its precision and convenience, the proposed model may relatively facilitate the application of single-edge notched or uniaxial central tearing tests.
- 1 June 2022
- Published by SAGE Publications in Journal of Industrial Textiles
- Vol. 51 (4_suppl) , 5560S-5591S
Modified stress field model for critical tearing strength of architectural coated fabrics
This report presents a new critical tearing strength prediction model, the modified stress field model. Firstly, the critical tearing strength of six coated fabrics is obtained using the single-edge notched tests. The results show that the warp and weft strength utilization of different coated fabrics is similar. Based on the test data, the prediction effects, parameter meanings, and basic properties of three models, namely Thiele’s empirical formula, the stress field model, and the modified stress field model, are discussed and compared. Then, the predicted results and properties of the three models in different crack ranges, specifically the small crack range, are compared, and their application scopes are verified. The two commonly used models lack the improved prediction effects in the small crack range that is provided by the modified stress field model. Finally, to reduce the workload while maintaining a certain accuracy, a crack combination of 3 mm + 15 mm is recommended, which is further confirmed using the root-mean-square error index. The prediction results of Thiele’s empirical formula and the modified stress field model under this crack combination are compared. The new model can still maintain good prediction effects even when extrapolating for small cracks using limited test data. Because of its precision and convenience, the proposed model may relatively facilitate the application of single-edge notched or uniaxial central tearing tests.
- 7 October 2021
- Published by SAGE Publications in Textile Research Journal
- Vol. 92 (5-6) , 929-953
Tearing behaviors of polytetrafluoroethylene coated fabric under uniaxial in-plane tearing tests
This study conducts alternative-basic-angle trapezoidal tearing and single-edge notch tearing tests on a polytetrafluoroethylene coated woven fabric, where the two methods are related through the basic angle of a trapezoid. The tearing process and failure modes are carefully examined, and load–displacement curves and tearing strength are analyzed. The tearing process comprises three stages, which are distinguished photographically or in different load–displacement curve sections. Corresponding to these stages, failure modes can be classified into three parts with varying extension directions. The effect of the basic angle is clearly illustrated. As the angle increases, three stages and parts appear in sequence; the tearing strength increases, but the larger one changes from weft to warp. The relationship between the tearing process and tearing strength is described. The three stages correspond to the increase in tearing strength, occurrence of the maximum tearing strength, and failure. Because the single-edge notch tearing method is more complex and important, it is the method that is studied mainly. Digital image correlation equipment is used to observe the strain distribution at the crack section. Moreover, the applications of four frequently used models are investigated. The results indicate that Thiele’s empirical formula offers the best simulation among the three tearing strength prediction models, and the theoretical stress distribution model also provides good simulation. Furthermore, a numerical simulation is conducted. The critical tearing strength and load–displacement curves before tearing initiates acquired through the simulation and test agree well. All results may provide basic data for future improvements in design theories.
- 7 October 2021
- Published by SAGE Publications in Textile Research Journal
- Vol. 92 (5-6) , 929-953
Tearing behaviors of polytetrafluoroethylene coated fabric under uniaxial in-plane tearing tests
This study conducts alternative-basic-angle trapezoidal tearing and single-edge notch tearing tests on a polytetrafluoroethylene coated woven fabric, where the two methods are related through the basic angle of a trapezoid. The tearing process and failure modes are carefully examined, and load–displacement curves and tearing strength are analyzed. The tearing process comprises three stages, which are distinguished photographically or in different load–displacement curve sections. Corresponding to these stages, failure modes can be classified into three parts with varying extension directions. The effect of the basic angle is clearly illustrated. As the angle increases, three stages and parts appear in sequence; the tearing strength increases, but the larger one changes from weft to warp. The relationship between the tearing process and tearing strength is described. The three stages correspond to the increase in tearing strength, occurrence of the maximum tearing strength, and failure. Because the single-edge notch tearing method is more complex and important, it is the method that is studied mainly. Digital image correlation equipment is used to observe the strain distribution at the crack section. Moreover, the applications of four frequently used models are investigated. The results indicate that Thiele’s empirical formula offers the best simulation among the three tearing strength prediction models, and the theoretical stress distribution model also provides good simulation. Furthermore, a numerical simulation is conducted. The critical tearing strength and load–displacement curves before tearing initiates acquired through the simulation and test agree well. All results may provide basic data for future improvements in design theories.