Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Zhijun Guo has a total of 39 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Research on the vibration frequency range of vibratory soil cutting system and experimental verification

    by Yiqing Qiu, Zhijun Guo, Xiaoliang Chen, Kun Zhang, Liyong Xu

    To address the wide variation in vibration frequencies used in existing vibratory soil cutting tools and the lack of a unified frequency selection criterion, this study investigated the natural vibration characteristics of soil in an indoor soil bin. Based on single-degree-of-freedom (SDOF) resonance theory, the empirical method, half-power bandwidth method, and amplitude magnification factor method were used to analyze the resonance bandwidth and vibration-energy proportion of the first-order soil vibration mode. On this basis, a frequency selection method for vibratory soil cutting tools was developed. The results show that the first-order natural vibration frequency f 0 of the soil is 29.492 Hz, with a damping ratio of 0.142. The resonance frequency bands determined by the empirical method and the amplitude amplification factor β = 2 are 0.75 f 0 ∼ 1.25 f 0 and 0.717 f 0 ∼ 1.207 f 0 , respectively. These bands strike a balance between vibration intensity and frequency adaptability, though their ranges are relatively limited. The effective vibration frequency band corresponding to an amplitude amplification factor β = 1 is the widest, ranging from 0 ∼ 1.414 f 0 , which can significantly enhance the equipment’s adaptability to variations in soil parameters, although the vibration response intensity is somewhat reduced. Balancing vibration intensity and engineering applicability, the recommended vibration frequency range for vibrating soil cutting equipment is proposed to be 0.75 f 0 ∼ 1.414 f 0 . To verify the validity of the proposed frequency range, 15 spatial spectrum bulldozing plate prototypes were designed and fabricated using five spatial spectrum excitation frequency levels and three amplitude levels, and soil bin cutting tests were conducted. The test results indicate that spatial spectrum bulldozing plates within the recommended frequency range generally exhibit good drag reduction and detachment performance, with the best drag reduction effect observed when the excitation frequency is close to the soil’s natural vibration frequency. Compared with traditional parabolic bulldozing plates, the relative drag reduction rate of the bulldozing plates reached 14.66% under the optimal parameter combination. The test results validated the rationality of the proposed vibration frequency selection range and selection principles. The research findings provide a theoretical basis for the design of vibration parameters for vibratory soil cutting implements and the optimization of the spatial spectrum structure of soil-engaging components.

  • Open Access

    Trajectory Tracking of Intelligent Sweeping Vehicles Based on Adaptive Strong Tracking EKF and Laguerre MPC

    by Zhijun Guo, Hao Su, Tong Zhang, Yanan Tu, Yixuan Li, Mingtian Pang

    To improve the accuracy and real-time performance of trajectory tracking control for a four-wheel differential drive intelligent sweeping vehicle, a trajectory tracking control method based on an adaptive strong tracking extended Kalman filter (ASTEKF) state estimator and a Laguerre-based model predictive controller (LMPC) is proposed. Based on the kinematic model of the intelligent sweeping vehicle, an ASTEKF state estimator is designed for vehicle state estimation, and a Laguerre-function-based model predictive controller is developed for trajectory tracking control, thereby enhancing the control accuracy and stability of the vehicle. Simulation results demonstrate that compared with the conventional MPC algorithm, the proposed ASTEKF–LMPC algorithm reduces the maximum lateral error by 44.65% and the maximum heading angle error by 40.96% during sweeping operations, while under normal driving conditions, the maximum lateral error and maximum heading angle error are reduced by 36.27% and 40.03%, respectively. Furthermore, experimental tests conducted on an intelligent sweeping vehicle platform show that the proposed method reduces the maximum lateral error by 34.25% and the maximum heading angle error by 23.18%, thereby validating the effectiveness of the proposed algorithm in intelligent sweeping operations.

  • Open Access

    Research on Mobile Robot Path Planning Using Improved Whale Optimization Algorithm Integrated with Bird Navigation Mechanism

    by Zhijun Guo, Tong Zhang, Hao Su, Shilei Jie, Yanan Tu, Yixuan Li

    In order to solve the problems of slow convergence speed, insufficient accuracy, and easily falling into the local optimum of the traditional whale optimization algorithm (WOA) in mobile robot path planning, an improved whale optimization algorithm (IWOA) combined with the bird navigation mechanism was proposed. Specific improvement measures include using logical chaos mapping to initialize the population to enhance the randomness and diversity of the initial solution, designing a nonlinear convergence factor to prevent the algorithm from prematurely entering the shrinking surround phase and extending the global search time, introducing an adaptive spiral shape constant to dynamically adjust the search range to balance exploration and development capabilities, optimizing the individual update strategy in combination with the bird navigation mechanism, and optimizing the algorithm through companion position information, thereby improving the stability and convergence speed of the algorithm. Path planning simulations were performed on 30 × 30 and 50 × 50 grid maps. The results show that compared with WOA, MSWOA, and GA, in the 30 × 30 map, the path length of IWOA is shortened by 3.23%, 7.16%, and 6.49%, respectively; in the 50 × 50 map, the path length is shortened by 4.88%, 4.53%, and 28.37%, respectively. This study shows that IWOA has significant advantages in the accuracy and efficiency of path planning, which verifies its feasibility and superiority.


  • Open Access

    Design and Analysis of an MPC-PID-Based Double-Loop Trajectory Tracking Algorithm for Intelligent Sweeping Vehicles

    by Zhijun Guo, Mingtian Pang, Shiwen Ye, Yangyang Geng

    To enhance the precision and real-time performance of trajectory tracking control in differential-steering intelligent sweeping robots and to improve the adaptability of the control algorithm to errors caused by sensor noise, tire slip, and skid, an MPC-PID (Model Predictive Control–Proportional-Integral-Derivative) dual closed-loop control strategy was proposed. This strategy integrates a Kalman filter-based state estimator and a sliding compensation module. Based on the kinematic model of the intelligent sweeping robot, a model predictive controller (MPC) was designed to regulate the vehicle’s pose, while a PID controller was used to adjust the longitudinal speed, forming a dual closed-loop control algorithm. A Kalman filter was employed for state estimation, and a sliding compensation module was introduced to mitigate wheel slip and lateral drift, thereby improving the stability of the control system. Simulation results demonstrated that, compared to traditional MPC control, the maximum lateral deviation, maximum heading angle deviation, and speed response time were reduced by 50.83%, 53.65%, and 7.10%, respectively, during sweeping operations. In normal driving conditions, these parameters were improved by 41.58%, 45.54%, and 24.17%, respectively. Experimental validation on an intelligent sweeper platform demonstrates that the proposed algorithm achieves a 16.48% reduction in maximum lateral deviation and 9.52% faster speed response time compared to traditional MPC, effectively validating its enhanced tracking effectiveness in intelligent cleaning operations.


  • Open Access

    Research on Adhesion Performance of Track Monomer with Bionic Structure

    by Sanling Fu, Xiahua Cui, Le Yang, Xinyue Wang, Zhijun Guo, Fu Zhang

    Goats can walk freely and flexibly in complex environments such as concave and convex or soft ground. And their flexible spine has functions such as adjusting balance and providing auxiliary power during movement, while the limbs only have support functions. The spine has an adjustable and decisive role in the pressure on the sole of the hoof of the goat. Therefore, the goat spine was taken as the bionic prototype, the three-dimensional force distribution of the goat body space was analyzed, and the optimal spinal space curve was explored, combined with the goat gait cycle. Based on the study of spinal curve arrangement and placement, the spinal curve was stretched along the grouser length direction. The soil contact surface structure of the track monomer was constructed based on functional simulation. And the bionic structure of the track monomer with superior adhesion performance was explored. The results of simulation analysis and soil tank test both showed that the attachment performance of bionic structure was better than that of an ordinary structure. It showed that adding bionic curves to the contact surface of the track monomer could significantly improve the adhesion performance, and the bionic structure with a single bionic curve arranged on the complete contact surface of the track monomer had the best adhesion performance. Moreover, the adhesion of the optimal track monomer bionic structure was increased by 19.22 N compared with an ordinary structure in the soil tank test, which verified the superiority of the track monomer bionic structure design. It provides a new method and a new idea for improving the adhesion performance of tracked vehicle in hilly areas.


  • Open Access

    Research on the Resistance Reduction Law of Self-Excited a Resonant Circular Arc-Surface Bulldozing Plate Based on the Discrete Element Method

    by Zhijun Guo, Yiqing Qiu, Xianghai Yan, Jiajia Wang, Shengjie Si, Fugui Guo, Fu Zhang

    We explore the mechanism and law of reducing the resistance of soil cutting tools by achieving the self-excited vibration mode through the modification of the soil-engaging surface spectrum. Around the fundamental resonance point of the soil, and superimposing geometric waveforms of different spatial frequencies and amplitudes on the basis of the circular arc surface base directrix, 18 bulldozing plate models with different soil-engaging surface spectrum structures were designed and manufactured. By conducting a discrete element method (DEM) simulation of the working process of the bulldozing plate and comparing the working resistance of the soil-engaging components with the results of the soil bin test, the microscopic process of soil disturbance was further revealed from the perspective of simulation. The results indicate that the self-excited vibrating circular arc-surface bulldozing plate could effectively improve the resistance reduction effect during the operation around the resonance point. With this model, the average error of the horizontal working resistance was 7.52%, and the average error of the vertical working resistance was 21.71%. The analysis of the soil microscopic disturbance process by DEM simulation further verified the correctness of the macroscopic test results. The research work has an important reference value for both the vibration resistance reduction design of soil cutting tools and resistance reduction design of soil-engaging surfaces’ geometric structure modification.


  • Open Access

    Self-Excited-Resonance of Soil-Engaging Surface Spectrum: A New Method of Soil Cutting Resistance Reduction

    by Zhijun Guo, Yiqing Qiu, Xianghai Yan, Jiajia Wang, Yin Zhang, Pangang Zhang, Fu Zhang

    In this study we explored the methods and effects of spectral resistance reduction for soil-engaging surface of self-excited resonant bulldozing plates with a plane base on the basis of resonance effects. In the acquisition of the low-order vibration frequency f0 of the bin soil, centering around frequency point f0, eight spatial geometric wave frequency points ni of soil-engaging surfaces and three amplitudes were selected; by superimposing with soil-engaging surfaces of plane-based bulldozing plates, 24 spectral structures of the soil-engaging surface of bulldozing plates and model samples were combinatorically designed. Resistance reduction characteristics of each model sample were tested using an indoor soil bin test. Near the resonance point f0, the structures of the self-excited vibrating frequency spectrum of the soil-engaging surface obtain a preferable inhibitory effect on working resistance. At a 4 mm amplitude resonance point, model samples achieved the best resistance reduction effect, with a maximum relative resistance reduction rate of 22.67%, and the soil desorption effect of the relevant model sample was also good. On the other hand, away from the resonance point, whether the frequency increased or decreased, the corresponding working resistance of the model sample surfaces increased relatively. This is in good agreement with the law that the resonance point amplitude of the theoretical resonance curve is higher and the amplitude on both sides is lower. This paper provides a reference for the parameter design and related product development for various forced or self-excited vibration soil cutting tools.


  • Open Access

    Design and Test of Tread-Pattern Structure of Biomimetic Goat-Sole Tires

    by Fu Zhang, Yubo Qiu, Shuai Teng, Xiahua Cui, Xinyue Wang, Haoxun Sun, Shaukat Ali, Zhijun Guo, Jiajia Wang, Sanling Fu

    To solve the technical problem that wheeled vehicles are prone to skidding on complex ground, due to poor adhesion performance, a tire-tread-structure design method based on the bionic principle is proposed in this paper. The 3D model of a goat’s foot was obtained using reverse engineering technology, and the curve equation was fitted by extracting the contour data of its outer-hoof flap edge, which was applied to the tire-tread-structure design. The bionic and herringbone-pattern rubber samples were manufactured, and a soil-tank test was carried out using an electronic universal tensile-testing machine, in order to verify the simulation results. The results showed that the overall adhesion of the bionic tread-pattern was greater than that of the normal tread-pattern with the same load applied and the same height and angle of the tread-pattern structure, and the maximum adhesion was increased by 14.23%. This research will provide a reference for optimizing the pattern structure and thus improving the passing performance of wheeled vehicles.


  • Open Access

    Analysis of Kinematic Characteristics of Saanen Goat Spine under Multi-Slope

    by Fu Zhang, Xiahua Cui, Shunqing Wang, Haoxuan Sun, Jiajia Wang, Xinyue Wang, Sanling Fu, Zhijun Guo

    In order to improve the slope movement stability and flexibility of quadruped robot, a theoretical design method of a flexible spine of a robot that was based on bionics was proposed. The kinematic characteristics of the spine were analyzed under different slopes with a Saanen goat as the research object. A Qualisys track manager (QTM) gait analysis system was used to obtain the trunk movement of goats under multiple slopes, and linear time normalization (LTN) was used to calibrate and match typical gait cycles to characterize the goat locomotion gait under slopes. Firstly, the spatial angle changes of cervical thoracic vertebrae, thoracolumbar vertebrae, and lumbar vertebrae were compared and analyzed under 0°, 5°, 10°, and 15° slopes, and it was found that the rigid and flexible coupling structure between the thoraco–lumbar vertebrae played an obvious role when moving on the slope. Moreover, with the increase in slope, the movement of the spine changed to the coupling movement of thoraco–lumbar coordination movement and a flexible swing of lumbar vertebrae. Then, the Gaussian mixture model (GMM) clustering algorithm was used to analyze the changes of the thoraco–lumbar vertebrae and lumbar vertebrae in different directions. Combined with anatomical knowledge, it was found that the motion of the thoraco–lumbar vertebrae and lumbar vertebrae in the goat was mainly manifested as a left–right swing in the coronal plane. Finally, on the basis of the analysis of the maximin and variation range of the thoraco–lumbar vertebrae and lumbar vertebrae in the coronal plane, it was found that the coupling motion of the thoraco–lumbar cooperative motion and flexible swing of the lumbar vertebrae at the slope of 10° had the most significant effect on the motion stability. SSE, R2, adjusted-R2, and RMSE were used as evaluation indexes, and the general equations of the spatial fitting curve of the goat spine were obtained by curve fitting of Matlab software. Finally, Origin software was used to obtain the optimal fitting spatial equations under eight movements of the goat spine with SSE and adjusted-R2 as indexes. The research will provide an idea for the bionic spine design with variable stiffness and multi-direction flexible bending, as well as a theoretical reference for the torso design of a bionic quadruped robot.


  • Open Access

    Calibration and Verification Test of Cinnamon Soil Simulation Parameters Based on Discrete Element Method

    by Yiqing Qiu, Zhijun Guo, Xin Jin, Pangang Zhang, Shengjie Si, Fugui Guo

    To obtain the discrete element simulation model parameters suitable for the interaction between cinnamon soil and soil-engaging components, the Hertz–Mindlin with JKR contact model in EDEM simulation software was used to calibrate the relevant model parameters of cinnamon soil. Firstly, the particle size distribution, moisture content, volume density, Poisson’ s ratio, shear modulus, and other parameters of the cinnamon soil were measured with cinnamon soil as the research object. Further, taking the stacking angle as the response value, the Plackett–Burman test, the steepest climbing test, and the Box–Behnken were designed by using the Design-Expert software to calibrate and optimize the physical parameters of soil simulation. The optimal parameter combination was obtained: cinnamon soil–cinnamon soil rolling friction coefficient was 0.08, soil JKR surface energy was 0.37 J/m−2, and cinnamon soil–steel static friction coefficient was 0.64. Finally, the discrete element simulation verification test of stacking angle and cutting resistance was carried out under the calibrated parameters. The comparative calculation showed that the relative error between the simulated stacking angle and the measured stacking angle was 0.253%, and the maximum relative error between the simulated cutting resistance and the measured cutting resistance was 10.32%, which was within the acceptable range, indicating the high accuracy and reliability for the calibration parameters. The research results have important reference value for the energy-saving and consumption-reducing design of soil tillage components and provide basic data for the simulation of cutting resistance research of cinnamon-soil-engaging components.