PZPing Zhang

Ping Zhang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ping Zhang has a total of 18 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Influence of Molybdenum Addition on the Structure, Mechanical Properties, and Cutting Performance of AlTiN Coatings

    by Tao Yang, Jun Yin, Puyou Ying, Changhong Lin, Ping Zhang, Jianbo Wu, Alexander Kovalev, Min Huang, Tianle Wang, Andrei Y. Grigoriev, et al.

    Though AlTiN coating has been intensively studied, there is still a need to develop AlTiN coating to meet the growing demand of industrial machining. One effective way to improve the performance of AlTiN coating is by adding alloying elements. In this study, AlTiN and AlTiMo coatings were deposited using multi-arc ion plating to investigate the influence of molybdenum addition on the structure, mechanical properties, and cutting performance of AlTiN coatings. Spherical droplets formed on the surfaces of both coatings, with the AlTiMoN coating exhibiting more surface defects than the AlTiN coating. The grazing incidence X-ray diffraction results revealed the formation of an (Al,Ti)N phase formed in the AlTiN and AlTiMoN coatings. Molybdenum doping in the AlTiMoN coating slightly reduced the grain size. Both coatings exhibited excellent adhesion to the substrate. The hardness (H), elastic moduli (E), H/E, and H3/E2 ratios of the AlTiMoN coating were higher than those of the AlTiN coating. The improvement in the mechanical properties was attributed to grain refinement and solution strengthening. Molybdenum doping improved the tribological properties and cutting performance of the AlTiN coatings, which was ascribed to the formation of MoO3 as a solid lubricant. These results show a path to increase the performance of AlTiN coating through molybdenum addition and provide ideas for the application of AlTiMoN coatings for cutting tools.


  • Open Access

    Pre-Aging Effect on the Formation of Ω Phase and Mechanical Properties of the Al-Cu-Mg-Ag Alloy

    by Puyou Ying, Changhong Lin, Zhiyi Liu, Song Bai, Vladimir Levchenko, Ping Zhang, Jianbo Wu, Tao Yang, Min Huang, Gang Yang, et al.

    In the present work, different aging treatments were performed to investigate the pre-aging effect on the formation of Ω phase and mechanical properties in Al-Cu-Mg-Ag alloy. The results showed that pre-strain could inhibit the formation of Ω phases, which was detrimental to the alloy strength. Due to the introduction of pre-aging treatment before pre-strain, the adverse effect of pre-strain on the precipitation of the Ω phase was reduced, and the alloy strength was increased by at least 15 MPa. Besides this, increasing the pre-aging temperature promoted the precipitation of Ω phases, inhibited the formation of θ′ phases, and improved the alloy strength. This was because the higher pre-aging temperature promoted more pre-precipitated Ω phases in the pre-aging process, and most of the pre-precipitated Ω phases could be retained and grew in the subsequent aging process. As a result, the tensile strength of the alloy increased from 523 MPa to 540 MPa. In addition, pre-aging with a higher temperature consumed more solute atoms, leading to less residual solute atoms in the matrix. Thus, the adverse effects of pre-strain, which inhibit the formation of clusters by the segregation of solute atoms, were reduced.


  • Open Access

    Effect of Modulation Periods on the Mechanical and Tribological Performance of MoS2–TiL/MoS2–TiH Multilayer Coatings

    by Ping Zhang, Puyou Ying, Changhong Lin, Tao Yang, Jianbo Wu, Min Huang, Tianle Wang, Yihang Fang, Vladimir Levchenko

    MoS2–Ti coating is a widely used solid lubricant owing to its low friction coefficient. The mechanical and tribological performance of the coating can be further improved via introducing a multilayer structure, which is closely related to the modulation period and significantly affects the properties of the coating. Herein, the effect of two different modulation periods on the mechanical and tribological performance of the MoS2–TiL/MoS2–TiH multilayer coatings (where L and H represent low and high-powered sputtering of the titanium target) was studied. The performance of the coatings was found to depend on modulation periods of single layer thickness and thickness ratio, respectively. When the thickness ratio of MoS2–TiL layer to MoS2–TiH layer was fixed with different number of layers, the adverse effects of the interface outweighed the beneficial effect; thus, the mechanical and tribological performance of the multilayer coatings were improved with an increase in the single layer thickness. When the effect of the multilayer interfaces on the studied coatings was similar with the same number of layers, the MoS2–TiH layer had more impact on the hardness of the MoS2–TiL/MoS2–TiH multilayer coatings, whereas the MoS2–TiL layer substantially affected the adhesion properties, friction behavior and wear resistance. This study can provide a way to regulate coatings with different performance requirements via building different multilayer microstructures.