Zhuojie Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Zhuojie Zhang has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
Lu Wang
Associate Professor, School of Civil Engineering and Architecture, Southwest Univ. of Science and Technology, Sichuan 621010, China
2 shared publicationsXiaoxia Zhen
Associate Professor, School of Civil Engineering and Transportation, South China Univ. of Technology, Guangzhou 510640, China
2 shared publicationsYonglin Zhao
Ph.D. Candidate, School of Civil Engineering and Transportation, South China Univ. of Technology, Guangzhou 510640, China
2 shared publications- Chenglong Wu
School of Civil Engineering and Transportation, South China University of Technology, Guangzhou, China
1 shared publication Danfeng Li
School of Architecture and Civil Engineering, Taizhou University, Taizhou, China
1 shared publication- Danfeng Li
State Key Laboratory of Mechanical Behavior and System Safety of Traffic Engineering Structures
1 shared publication
Latest Publications
- 20 January 2026
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 114 (2) , 126
Semi-active control on sling vibrations by the time-delayed velocity feedback with magnetorheological dampers
- 20 January 2026
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 114 (2) , 126
Semi-active control on sling vibrations by the time-delayed velocity feedback with magnetorheological dampers
- 2 August 2023
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 37 (8) , 3961-3973
Hysteretic behavior of multi-layered beams with Coulomb friction interface law
- 2 August 2023
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 37 (8) , 3961-3973
Hysteretic behavior of multi-layered beams with Coulomb friction interface law
- Open Access
- 31 May 2023
- Published by Springer Nature in Scientific Reports
- Vol. 13 (1) , 1-17
Improved measurement method for roadbed bearing capacity based on PFWD dynamic modulus control
To address current challenges of difficult standardisation of dynamic determination of roadbed bearing capacity and excessive deviations in deflection control, this paper proposes a improved measurement method for roadbed load-bearing capacity based on the dynamic modulus control using a portable falling weight deflectometer (PFWD). The detection range of PFWD is determined by theoretical analysis. Based on the range, a finite element numerical model was developed, the spatial distribution and attenuation of the dynamic stress of the roadbed soil in the depth and horizontal directions are determined. The variation of the vertical dynamic stress with depth is not characterized by a gradual decrease, as is commonly believed, but rather by an increase followed by a decrease. The underlying reasons for the difference between static and dynamic indicators are explored. Using the improved method, a prediction model with dynamic bending as the detection index and static rebound modulus as the control index was developed. The proposed model can improve precision accuracy as well as detection efficiency, verify the effectiveness of the improved method, which is important for accurate dynamic measurement and evaluation of highway roadbed bearing capacity.
- 31 May 2023
- Published by Springer Nature in Scientific Reports
- Vol. 13 (1) , 1-17
Open AccessImproved measurement method for roadbed bearing capacity based on PFWD dynamic modulus control
To address current challenges of difficult standardisation of dynamic determination of roadbed bearing capacity and excessive deviations in deflection control, this paper proposes a improved measurement method for roadbed load-bearing capacity based on the dynamic modulus control using a portable falling weight deflectometer (PFWD). The detection range of PFWD is determined by theoretical analysis. Based on the range, a finite element numerical model was developed, the spatial distribution and attenuation of the dynamic stress of the roadbed soil in the depth and horizontal directions are determined. The variation of the vertical dynamic stress with depth is not characterized by a gradual decrease, as is commonly believed, but rather by an increase followed by a decrease. The underlying reasons for the difference between static and dynamic indicators are explored. Using the improved method, a prediction model with dynamic bending as the detection index and static rebound modulus as the control index was developed. The proposed model can improve precision accuracy as well as detection efficiency, verify the effectiveness of the improved method, which is important for accurate dynamic measurement and evaluation of highway roadbed bearing capacity.
- Open Access
- 1 January 2021
- Published by Wiley in Advances in Civil Engineering
- Vol. 2021 (1)
The Anti sliding Mechanism of Adjacent Pile‐Anchor Structure considering Traffic Load on Slope Top
In view of the fact that the anti sliding effect analysis of the current anchor cable and anti slide pile structure is not yet complete, research on the synergy mechanism of adjacent pile‐anchor composite structures under traffic load is carried out. Firstly, a free vibration analysis for the slope dynamic model is carried out by using a three‐dimensional finite element numerical simulation method. By improving the slope boundary conditions of time‐domain analysis, the time‐domain equation of the dynamic model of traffic load acting on the top of the slope is solved accurately, and the response law of the internal force of the pile anchor composite structure is also described. The mechanism by which the pile anchor composite structure resists against the slope sliding through the internal force increment is proposed: this internal force increment is estimated to be 73.4%, while that of anchor cable is 26.6%. The composite structure presents the coordinated sharing for sliding force. The internal force of the lower row of anchor cables is 89.48 kN larger than that of the upper row, and the internal force increment is four times larger, indicating that the lower anchor cable is more effective in slope reinforcement. As the deformation at the top of the slope is greater, the prestress of the upper anchor cable should be increased to avoid the “chain failure” caused by excessive deformation. As a result, the coordination law of internal force of pile anchor is revealed, and the anti sliding sharing mechanism is clarified. A design idea of the adjacent pile‐anchor composite structure is proposed, which takes 0.2‐0.3 times the remaining sliding force as the design value of prestressed anchor cable. The idea fully considers the anti sliding effect of prestressed anchor cables and reduces the design size of anti slide pile section, providing a theoretical support for optimization design of combined anti slide structure and saving project investment.
- 1 January 2021
- Published by Wiley in Advances in Civil Engineering
- Vol. 2021 (1)
Open AccessThe Anti sliding Mechanism of Adjacent Pile‐Anchor Structure considering Traffic Load on Slope Top
In view of the fact that the anti sliding effect analysis of the current anchor cable and anti slide pile structure is not yet complete, research on the synergy mechanism of adjacent pile‐anchor composite structures under traffic load is carried out. Firstly, a free vibration analysis for the slope dynamic model is carried out by using a three‐dimensional finite element numerical simulation method. By improving the slope boundary conditions of time‐domain analysis, the time‐domain equation of the dynamic model of traffic load acting on the top of the slope is solved accurately, and the response law of the internal force of the pile anchor composite structure is also described. The mechanism by which the pile anchor composite structure resists against the slope sliding through the internal force increment is proposed: this internal force increment is estimated to be 73.4%, while that of anchor cable is 26.6%. The composite structure presents the coordinated sharing for sliding force. The internal force of the lower row of anchor cables is 89.48 kN larger than that of the upper row, and the internal force increment is four times larger, indicating that the lower anchor cable is more effective in slope reinforcement. As the deformation at the top of the slope is greater, the prestress of the upper anchor cable should be increased to avoid the “chain failure” caused by excessive deformation. As a result, the coordination law of internal force of pile anchor is revealed, and the anti sliding sharing mechanism is clarified. A design idea of the adjacent pile‐anchor composite structure is proposed, which takes 0.2‐0.3 times the remaining sliding force as the design value of prestressed anchor cable. The idea fully considers the anti sliding effect of prestressed anchor cables and reduces the design size of anti slide pile section, providing a theoretical support for optimization design of combined anti slide structure and saving project investment.