Muhammad Ziaul Arif
Muhammad Ziaul Arif has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Marko Vauhkonen
University of Eastern Finland
5 shared publications - Aku Seppänen
Department of Technical Physics, University of Eastern Finland, 70210 Kuopio, Finland
3 shared publications - Timo Lähivaara
University of Eastern Finland
2 shared publications - Ville Kolehmainen
Department of Technical Physics, University of Eastern Finland, Kuopio, Finland
2 shared publications - Eero Koponen
University of Eastern Finland
1 shared publication - Ossi Lehtikangas
Univ. of Eastern Finland (Finland)
1 shared publication
Latest Publications
- Open Access
- 29 September 2026
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 37 (39) , 395406
Dual-modality electrical tomography of stratified three-phase flows
Measuring volumetric flow rates in multiphase pipeline flows requires accurate estimates of both phase fractions and velocity fields, which remain key challenges in process industries. Electrical resistance tomography (ERT) and electrical capacitance tomography provide complementary information, via conductivity and permittivity, on volumetric phase fractions in two-phase flows, while electromagnetic flow tomography (EMFT) enables reconstruction of velocity fields. In this work, a previously introduced dual-modality ERT–EMFT framework for two-phase flow metering is extended to three-phase systems. Here, an electrical impedance tomography (EIT) system operating at 1 kHz and 40 MHz frequencies is used to obtain both conductivity and permittivity distributions, respectively. The proposed approach incorporates a complementary permittivity reconstruction and introduces a modified Maxwell’s model that jointly exploits the conductivity, permittivity, and velocity distributions to estimate the volumetric flow rates of all three phases. This allows the use of a dual-modality EIT–EMFT sensing system operating at low and high frequencies without requiring additional measurement hardware. Stratified three-phase oil-air-water flows were examined using numerical simulations. The resulting average volumetric flow rate errors were 4.9% for air, 6.8% for oil, and 0.4% for water—comparable to the accuracy previously achieved for two-phase oil–water flows.
- 29 September 2026
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 37 (39) , 395406
Open AccessDual-modality electrical tomography of stratified three-phase flows
Measuring volumetric flow rates in multiphase pipeline flows requires accurate estimates of both phase fractions and velocity fields, which remain key challenges in process industries. Electrical resistance tomography (ERT) and electrical capacitance tomography provide complementary information, via conductivity and permittivity, on volumetric phase fractions in two-phase flows, while electromagnetic flow tomography (EMFT) enables reconstruction of velocity fields. In this work, a previously introduced dual-modality ERT–EMFT framework for two-phase flow metering is extended to three-phase systems. Here, an electrical impedance tomography (EIT) system operating at 1 kHz and 40 MHz frequencies is used to obtain both conductivity and permittivity distributions, respectively. The proposed approach incorporates a complementary permittivity reconstruction and introduces a modified Maxwell’s model that jointly exploits the conductivity, permittivity, and velocity distributions to estimate the volumetric flow rates of all three phases. This allows the use of a dual-modality EIT–EMFT sensing system operating at low and high frequencies without requiring additional measurement hardware. Stratified three-phase oil-air-water flows were examined using numerical simulations. The resulting average volumetric flow rate errors were 4.9% for air, 6.8% for oil, and 0.4% for water—comparable to the accuracy previously achieved for two-phase oil–water flows.
- 11 April 2024
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 35 (7) , 075302
Deep learning-assisted dual-modal tomography for phase flow rate estimation in two-phase oil-water flow systems
Accurately estimating phase flow rates in multiphase systems is crucial for many industries, where precise measurements are essential for operational efficiency and safety. Addressing this issue, this paper introduces an approach that employs deep learning-assisted dual-modal electromagnetic flow tomography (EMFT) and electrical tomography (ET) to predict both oil and water flow rates in two-phase oil-water flows. To facilitate the generation of the data, we first simulate diverse flow conditions using COMSOL Multiphysics software and the convection–diffusion equation, aiming to create a realistic representation of two-phase oil-water flows. The dual-modal system measurement data, generated from these simulations and simulated by using a dense finite element mesh, provide reliable inputs for the deep learning model. Moreover, this study also integrates experimental data into both the training and testing phases, improving the ability of the proposed approach to estimate flow rates accurately in practical investigations. The results from laboratory experiments demonstrate the potential of the deep learning-assisted dual-modal ET and EMFT approach in effectively resolving the challenges of estimating flow rates in two-phase oil-water flow systems. By combining the deep learning capabilities with dual-modal tomography, this study offers valuable insights for future applications and represents a significant step forward in the field of multiphase flow rate estimation.
- 11 April 2024
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 35 (7) , 075302
Deep learning-assisted dual-modal tomography for phase flow rate estimation in two-phase oil-water flow systems
Accurately estimating phase flow rates in multiphase systems is crucial for many industries, where precise measurements are essential for operational efficiency and safety. Addressing this issue, this paper introduces an approach that employs deep learning-assisted dual-modal electromagnetic flow tomography (EMFT) and electrical tomography (ET) to predict both oil and water flow rates in two-phase oil-water flows. To facilitate the generation of the data, we first simulate diverse flow conditions using COMSOL Multiphysics software and the convection–diffusion equation, aiming to create a realistic representation of two-phase oil-water flows. The dual-modal system measurement data, generated from these simulations and simulated by using a dense finite element mesh, provide reliable inputs for the deep learning model. Moreover, this study also integrates experimental data into both the training and testing phases, improving the ability of the proposed approach to estimate flow rates accurately in practical investigations. The results from laboratory experiments demonstrate the potential of the deep learning-assisted dual-modal ET and EMFT approach in effectively resolving the challenges of estimating flow rates in two-phase oil-water flow systems. By combining the deep learning capabilities with dual-modal tomography, this study offers valuable insights for future applications and represents a significant step forward in the field of multiphase flow rate estimation.
- Open Access
- 28 June 2023
- Published by IOP Publishing in Inverse Problems
- Vol. 39 (8) , 084003
State estimation approach to dual-modal imaging of two-phase flow based on electromagnetic flow tomography and electrical tomography
Monitoring, control and design of industrial processes involving multiphase flows often call for analysis of data from multiple sensors which give information on different quantities of the flowing materials. An example of such case is the problem of monitoring the flow of oil–water mixture: the phase fractions of oil and water, their velocities and volumetric flow rates cannot be retrieved from measurements given by a single sensing/imaging modality. For this reason, multi-modal tomographic imaging systems have been developed. In multi-phase flows, the quantities retrieved from different tomographic instruments are often interconnected—for example, the evolutions of the phase fractions depend on their velocities and vice versa. However, the analysis of data from different tomographic modalities is usually done separately—without taking into account physics that link the quantities of interest. In this paper, we propose a novel approach to image reconstruction in dual-modal tomography of multiphase flows. The governing idea is to combine the two modalities via Bayesian state estimation, that is, we write models that approximate connections between different quantities involved in the process and use sequential measurements from both modalities to jointly estimate these temporally evolving quantities. As an example case, we consider a dual-modal system comprising the electromagnetic flow tomography (EMFT) and electrical tomography (ET). While the EMFT is sensitive to the velocity field but also depends on the phase fractions of fluids, ET measurements are directly linked to phase fractions only. We study the performance of state estimation in EMFT-ET tomography with a set of numerical simulations. The results demonstrate that it outperforms the conventional stationary reconstruction approach, and also provides means for uncertainty quantification in multiphase flow imaging.
- 28 June 2023
- Published by IOP Publishing in Inverse Problems
- Vol. 39 (8) , 084003
Open AccessState estimation approach to dual-modal imaging of two-phase flow based on electromagnetic flow tomography and electrical tomography
Monitoring, control and design of industrial processes involving multiphase flows often call for analysis of data from multiple sensors which give information on different quantities of the flowing materials. An example of such case is the problem of monitoring the flow of oil–water mixture: the phase fractions of oil and water, their velocities and volumetric flow rates cannot be retrieved from measurements given by a single sensing/imaging modality. For this reason, multi-modal tomographic imaging systems have been developed. In multi-phase flows, the quantities retrieved from different tomographic instruments are often interconnected—for example, the evolutions of the phase fractions depend on their velocities and vice versa. However, the analysis of data from different tomographic modalities is usually done separately—without taking into account physics that link the quantities of interest. In this paper, we propose a novel approach to image reconstruction in dual-modal tomography of multiphase flows. The governing idea is to combine the two modalities via Bayesian state estimation, that is, we write models that approximate connections between different quantities involved in the process and use sequential measurements from both modalities to jointly estimate these temporally evolving quantities. As an example case, we consider a dual-modal system comprising the electromagnetic flow tomography (EMFT) and electrical tomography (ET). While the EMFT is sensitive to the velocity field but also depends on the phase fractions of fluids, ET measurements are directly linked to phase fractions only. We study the performance of state estimation in EMFT-ET tomography with a set of numerical simulations. The results demonstrate that it outperforms the conventional stationary reconstruction approach, and also provides means for uncertainty quantification in multiphase flow imaging.
- Open Access
Dual-Modal Electrical Imaging of Two-Phase Flow—Experimental Evaluation of the State Estimation Approach
Accurate measurement of two-phase flow quantities is essential for managing production in many industries. However, the inherent complexity of two-phase flow often makes estimating these quantities difficult, necessitating the development of reliable techniques for quantifying two-phase flow. In this paper, we investigated the feasibility of using state estimation for dynamic image reconstruction in dual-modal tomography of two-phase oil–water flow. We utilized electromagnetic flow tomography (EMFT) to estimate velocity fields and electrical tomography (ET) to determine phase fraction distributions. In state estimation, the contribution of the velocity field to the temporal evolution of the phase fraction distribution was accounted for by approximating the process with a convection–diffusion model. The extended Kalman filter (EKF) and fixed-interval Kalman smoother (FIKS) were used to reconstruct the temporally evolving velocity and phase fraction distributions, which were further used to estimate the volumetric flow rates of the phases. Experimental results on a laboratory setup showed that the FIKS approach outperformed the conventional stationary reconstructions, with the average relative errors of the volumetric flow rates of oil and water being less than 4%. The FIKS approach also provided feasible uncertainty estimates for the velocity, phase fraction, and volumetric flow rate of the phases, enhancing the reliability of the state estimation approach.
Open AccessDual-Modal Electrical Imaging of Two-Phase Flow—Experimental Evaluation of the State Estimation Approach
Accurate measurement of two-phase flow quantities is essential for managing production in many industries. However, the inherent complexity of two-phase flow often makes estimating these quantities difficult, necessitating the development of reliable techniques for quantifying two-phase flow. In this paper, we investigated the feasibility of using state estimation for dynamic image reconstruction in dual-modal tomography of two-phase oil–water flow. We utilized electromagnetic flow tomography (EMFT) to estimate velocity fields and electrical tomography (ET) to determine phase fraction distributions. In state estimation, the contribution of the velocity field to the temporal evolution of the phase fraction distribution was accounted for by approximating the process with a convection–diffusion model. The extended Kalman filter (EKF) and fixed-interval Kalman smoother (FIKS) were used to reconstruct the temporally evolving velocity and phase fraction distributions, which were further used to estimate the volumetric flow rates of the phases. Experimental results on a laboratory setup showed that the FIKS approach outperformed the conventional stationary reconstructions, with the average relative errors of the volumetric flow rates of oil and water being less than 4%. The FIKS approach also provided feasible uncertainty estimates for the velocity, phase fraction, and volumetric flow rate of the phases, enhancing the reliability of the state estimation approach.
- 8 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 70 (00189456) , 1-17
Joint Reconstruction of Conductivity and Velocity in Two-Phase Flows Using Electromagnetic Flow Tomography and Electrical Tomography: A Simulation Study
Characterization of two-phase flows is a common problem in the process industry. Due to complexity of flows, having accurate measurements of velocity fields, phase fractions, and the volumetric flow rates is challenging. Even though several approaches have been developed, accurate measurements of the flow quantities remain a challenge. Metering volumetric flow rate requires information on the local phase fraction and velocity field in the pipe cross section to be imaged. These data are commonly obtained using two individual measurement systems, the so-called dual-modality system. This article considers a dual-modality consisting of electromagnetic flow tomography (EMFT) and electrical tomography (ET) imaging, which provide information on the velocity field and electrical conductivity distribution, respectively; the combination of EMFT and ET reconstruction can be further used for inferring the volumetric flow rate. The aim of this article is to improve the accuracy of the EMFT and ET reconstructions—and the resulting flow rate estimate—by enhanced modeling of the unknown velocity and conductivity fields. More specifically, the proposed approach is based on modeling the joint statistics of the velocity and conductivity with a cross-covariance matrix which is based on a representative ensemble of velocity–conductivity image pairs obtained, for example, from fluid dynamical modeling or empirically. The cross-covariance matrix is incorporated in the joint reconstruction within the Bayesian inverse problems framework as an additional prior model. The proposed image reconstruction approach is tested with a set of numerical simulations. The results show that the joint reconstruction approach (JRA) with a cross-covariance model is capable of improving the accuracy of the estimates compared to the approaches that are currently in use.
- 8 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 70 (00189456) , 1-17
Joint Reconstruction of Conductivity and Velocity in Two-Phase Flows Using Electromagnetic Flow Tomography and Electrical Tomography: A Simulation Study
Characterization of two-phase flows is a common problem in the process industry. Due to complexity of flows, having accurate measurements of velocity fields, phase fractions, and the volumetric flow rates is challenging. Even though several approaches have been developed, accurate measurements of the flow quantities remain a challenge. Metering volumetric flow rate requires information on the local phase fraction and velocity field in the pipe cross section to be imaged. These data are commonly obtained using two individual measurement systems, the so-called dual-modality system. This article considers a dual-modality consisting of electromagnetic flow tomography (EMFT) and electrical tomography (ET) imaging, which provide information on the velocity field and electrical conductivity distribution, respectively; the combination of EMFT and ET reconstruction can be further used for inferring the volumetric flow rate. The aim of this article is to improve the accuracy of the EMFT and ET reconstructions—and the resulting flow rate estimate—by enhanced modeling of the unknown velocity and conductivity fields. More specifically, the proposed approach is based on modeling the joint statistics of the velocity and conductivity with a cross-covariance matrix which is based on a representative ensemble of velocity–conductivity image pairs obtained, for example, from fluid dynamical modeling or empirically. The cross-covariance matrix is incorporated in the joint reconstruction within the Bayesian inverse problems framework as an additional prior model. The proposed image reconstruction approach is tested with a set of numerical simulations. The results show that the joint reconstruction approach (JRA) with a cross-covariance model is capable of improving the accuracy of the estimates compared to the approaches that are currently in use.