MZMingjing Zhang

Mingjing Zhang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mingjing Zhang has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Feasibility Study on the Steel-Plastic Geogrid Instead of Wire Mesh for Bolt Mesh Supporting

    by Qingbiao Wang, Dong Wang, Yue Li, Wenxia Liu, Chenglin Tian, Zhenyue Shi, Keyong Wang, Hongxu Song, Zhongjing Hu, Xu Zhang, et al.

    Wire mesh is a common material for bolt mesh supporting structures, but its application in engineering has revealed many defects. At the same time, with the development of new materials for civil engineering, the new material mesh performance and cost show outstanding advantages over wire mesh. In this paper, the feasibility of replacing wire mesh with steel-plastic geogrid as an alternative material is carefully studied through indoor tests and field applications. The following conclusions were drawn from a comparative analysis with wire mesh, mainly in terms of mechanical properties, engineering characteristics, and construction techniques: (1) in terms of mesh wire strength, wire mesh is slightly better than steel-plastic geogrid, but in the case of similar tensile strength, the amount of steel used per unit length of steel geogrid bars is only 36.75% of that of steel-plastic geogrid, while the tensile strength of the high-strength steel wire attached to the steel-plastic geogrid belt is about 3.3 times that of steel bars; (2) in terms of junction peel strength, both values are similar, with the injection-moulded junction being 1154.56–1224.38 N and the welded junction of 4 mm mesh being 988.35 N; (3) in terms of the strength of the mesh, steel-plastic geogrid is better than wire mesh, and with the same mesh wire strength, the bearing capacity of steel-plastic geogrid is increased by about 63.17% and the contribution of the mesh wire bearing capacity is increased by 83.66%, with the damage mainly being in the form of wire breakage in the ribbon causing ribbon failure, leading to further damage to the mesh; (4) in terms of the engineering application of steel-plastic geogrid compared to wire mesh, the utilization rate of mesh increases by about 24.99%, the construction efficiency increases by about 14.10%, and the economic benefit increases by about 45.31%. In practical application, the steel-plastic geogrid has good adhesion with surrounding rock and strong corrosion resistance. According to the above research analysis, the steel-plastic geogrid is feasible to replace the wire mesh for bolt mesh supporting.


  • Open Access

    Experimental Study on Tensile Mechanical Properties and Reinforcement Ratio of Steel–Plastic Compound Geogrid-Reinforced Belt

    by Qingbiao Wang, Yue Li, Hongxu Song, Jianing Duan, Zhongjing Hu, Fuqiang Wang, Haolin Xu, Zhengyin Liu, Mingjing Zhang, Liming Wang, et al.

    The steel–plastic compound geogrid has been widely used as a new reinforcement material in geotechnical engineering and other fields. Therefore, it is essential to fully understand the mechanical properties of steel–plastic compound geogrid-reinforced belts to utilize steel–plastic compound geogrids efficiently. In this study, tensile mechanical tests of steel wire, polyethylene geogrid belt, and steel–plastic compound geogrid-reinforced belt were conducted with respect to the tensile mechanical properties of steel–plastic compound geogrid-reinforced belts. In addition, the minimum reinforcement and optimal reinforcement ratios of steel–plastic compound geogrid-reinforced belts were summarized. The results showed that the steel–plastic compound geogrid-reinforced belts possessed an incongruent force of the internal steel wire during the tensile process. The tensile stress–strain curve of the steel–plastic compound geogrid-reinforced belt can be divided into the composite adjustment, steel wire breaking, and residual deformation stages. The tensile strength of the steel–plastic compound geogrid-reinforced belt is proportional to the diameter and number of steel wires in the reinforced belt. The minimum and optimum reinforcement ratios of steel wire in the steel–plastic compound geogrid-reinforced belt were 0.63% and 11.92%, respectively.