Lucille Despres
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Lucille Despres has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Jonathan Cormier
Physics and Mechanics of Materials Department Institut Pprime, UPR CNRS 3346, ISAE‐ENSMA Futuroscope‐Chasseneuil Cedex France
2 shared publications Alain Denoirjean
University of Limoges, CNRS, IRCER
1 shared publicationAlan Kéromnès
University of Limoges, CNRS, IRCER
1 shared publicationAlice Dolmaire
Université Paris Saclay
1 shared publicationArmelle Vardelle
University of Limoges, CNRS, IRCER
1 shared publicationAurélien Joulia
Safran Tech
1 shared publication
Latest Publications
- 6 December 2023
- Published by Springer Nature
- p. 37-85
Trends and Perspectives in Mitigating CMAS Infiltration in Thermal Barrier Coating
- 6 December 2023
- Published by Springer Nature
- p. 37-85
Trends and Perspectives in Mitigating CMAS Infiltration in Thermal Barrier Coating
- Open Access
Impact of Laser Texturing on Ni-Based Single Crystal Superalloys
Surface laser texturing is used to ensure mechanical anchoring and strengthen adhesion between the interfaces of bond coatless thermal barrier coating system. To anticipate a possible loss of mechanical properties and to adapt to the perpetual evolutions of chemical compositions of the system, we analyzed the microstructural evolutions of different Ni-based single crystal superalloys, induced during infrared nanosecond laser ablation. Localized asperities composed of a melted, re-solidified matter, with a different microstructure from that of the bulk material, were generated. Regarding asperity morphologies, recrystallization within the latter could be avoided. Then, to compare different Ni-base single crystal superalloys, the thermal-affected volumes were characterized for two patterns textured under different energetic conditions. It seems that all the studied single crystal superalloys behaved quite similarly during nanosecond laser ablation. Finally, according to these results, ablation kinetics between the γ and γ′ phases of Ni-based superalloys could not be homogeneous.
Open AccessImpact of Laser Texturing on Ni-Based Single Crystal Superalloys
Surface laser texturing is used to ensure mechanical anchoring and strengthen adhesion between the interfaces of bond coatless thermal barrier coating system. To anticipate a possible loss of mechanical properties and to adapt to the perpetual evolutions of chemical compositions of the system, we analyzed the microstructural evolutions of different Ni-based single crystal superalloys, induced during infrared nanosecond laser ablation. Localized asperities composed of a melted, re-solidified matter, with a different microstructure from that of the bulk material, were generated. Regarding asperity morphologies, recrystallization within the latter could be avoided. Then, to compare different Ni-base single crystal superalloys, the thermal-affected volumes were characterized for two patterns textured under different energetic conditions. It seems that all the studied single crystal superalloys behaved quite similarly during nanosecond laser ablation. Finally, according to these results, ablation kinetics between the γ and γ′ phases of Ni-based superalloys could not be homogeneous.
- Open Access
Ultra-High Temperature Creep of Ni-Based SX Superalloys at 1250 °C
Very high temperature creep properties of twelve different Ni-based single crystal superalloys have been investigated at 1250 °C and under different initial applied stresses. The creep strength at this temperature is mainly controlled by the remaining γ′ volume fraction. Other parameters such as the γ′ precipitate after microstructure evolution and the γ/γ′ lattice parameter mismatch seem to affect the creep strength to a lesser degree in these conditions. The Norton Law creep exponent lies in the range 6–9 for most of the alloys studied, suggesting that dislocation glide and climb are the rate limiting deformation mechanisms. Damage mechanisms in these extreme conditions comprise creep strain accumulation leading to pronounced necking and to recrystallization in the most severely deformed sections of the specimens.
Open AccessUltra-High Temperature Creep of Ni-Based SX Superalloys at 1250 °C
Very high temperature creep properties of twelve different Ni-based single crystal superalloys have been investigated at 1250 °C and under different initial applied stresses. The creep strength at this temperature is mainly controlled by the remaining γ′ volume fraction. Other parameters such as the γ′ precipitate after microstructure evolution and the γ/γ′ lattice parameter mismatch seem to affect the creep strength to a lesser degree in these conditions. The Norton Law creep exponent lies in the range 6–9 for most of the alloys studied, suggesting that dislocation glide and climb are the rate limiting deformation mechanisms. Damage mechanisms in these extreme conditions comprise creep strain accumulation leading to pronounced necking and to recrystallization in the most severely deformed sections of the specimens.