Nataniel Wontoon Barbosa Lima
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Nataniel Wontoon Barbosa Lima has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Marcos Honorato Oliveira
Universidade de Brasília, Brasil
2 shared publications - Maurício de Pina Ferreira
Institute of Technology, Federal University of Para, Belem 66075-110, Brazil
2 shared publications Brunna Ramos
Centro Universitário do Distrito Federal -UDF Centro Universitário do Distrito Federal -UDF Distrito Federal; Brasil Distrito Federal; Brasil
1 shared publication- C.A. Teixeira
Federal Territorial University of the Semi-Arid (UFERSA) Dept. of Exact and Natural Sciences - Mossoro, RN, Brazil
1 shared publication Eduardo Veloso dos Santos
Universidade de Brasília, Brasil
1 shared publication- Elmer Rolando Llanos Villarreal
Department of Natural Sciences, Mathematics, and Statistics, Federal Rural University of Semi-arid (DCME-UFERSA), Mossoró 59625-900, Brazil
1 shared publication
Latest Publications
- Open Access
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 17 (1) , e17113
Punching strength of flat slabs with shear reinforcement: considerations about the control perimeters
In structural design practice and scientific research on flat slabs, estimating the punching shear resistance of slab-column connection with shear reinforcement involves checking the shear stress acting on a control perimeter outside the shear-reinforced zone. Depending on the arrangement chosen for the shear reinforcement, the design codes` recommendations can lead to different interpretations of the geometry of the external control perimeter, which are, in some cases, also complex to formulate into closed-form equations. Thus, it is common that, especially in hand-made estimates, the slab-column connections are drawn, and dimensions of the external control perimeters are individually measured and applied to the design equations. This paper presents equations developed for ABNT NBR 6118, Eurocode 2 and ACI 318 to account for the length of the control perimeter outside the shear-reinforced zone, allowing the automated calculation for different shear reinforcement arrangements. The different interpretations of the geometry of the external control perimeter of these design codes are discussed and clarified. The proposed equations were validated by comparing their results with those obtained from individual drawing analysis of 62 slab-column connections with varied geometries and shear reinforcement arrangements, and the maximum error was up to 0.1%. This paper significantly contributes to the automation and optimisation of the punching shear strength estimates of slab-column connections with shear reinforcement, clarifying obscure points and automating the definition of the geometry of the external control perimeter.
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 17 (1) , e17113
Open AccessPunching strength of flat slabs with shear reinforcement: considerations about the control perimeters
In structural design practice and scientific research on flat slabs, estimating the punching shear resistance of slab-column connection with shear reinforcement involves checking the shear stress acting on a control perimeter outside the shear-reinforced zone. Depending on the arrangement chosen for the shear reinforcement, the design codes` recommendations can lead to different interpretations of the geometry of the external control perimeter, which are, in some cases, also complex to formulate into closed-form equations. Thus, it is common that, especially in hand-made estimates, the slab-column connections are drawn, and dimensions of the external control perimeters are individually measured and applied to the design equations. This paper presents equations developed for ABNT NBR 6118, Eurocode 2 and ACI 318 to account for the length of the control perimeter outside the shear-reinforced zone, allowing the automated calculation for different shear reinforcement arrangements. The different interpretations of the geometry of the external control perimeter of these design codes are discussed and clarified. The proposed equations were validated by comparing their results with those obtained from individual drawing analysis of 62 slab-column connections with varied geometries and shear reinforcement arrangements, and the maximum error was up to 0.1%. This paper significantly contributes to the automation and optimisation of the punching shear strength estimates of slab-column connections with shear reinforcement, clarifying obscure points and automating the definition of the geometry of the external control perimeter.
- Open Access
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Latin American Journal of Solids and Structures
- Vol. 21 (2) , e533
A parametric finite element study of concrete cone failure in headed bars under tensile loading
This article presents a parametric numerical study of the pullout behavior of headed bars embedded in concrete elements. The finite element model was developed using Abaqus software and validated to simulate the behavior of four pullout tests. The numerical results were validated against the experimental results and showed excellent agreement with the load-slip response and failure modes. Furthermore, a parametric numerical study with 23 simulations was planned to explore the influence of several variables on concrete cone failure, including concrete strength, flexural reinforcement ratio, geometry and head size, shaft diameter, and edge and group effects. The ultimate load results, failure modes, and influence on ultimate load are discussed.
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Latin American Journal of Solids and Structures
- Vol. 21 (2) , e533
Open AccessA parametric finite element study of concrete cone failure in headed bars under tensile loading
This article presents a parametric numerical study of the pullout behavior of headed bars embedded in concrete elements. The finite element model was developed using Abaqus software and validated to simulate the behavior of four pullout tests. The numerical results were validated against the experimental results and showed excellent agreement with the load-slip response and failure modes. Furthermore, a parametric numerical study with 23 simulations was planned to explore the influence of several variables on concrete cone failure, including concrete strength, flexural reinforcement ratio, geometry and head size, shaft diameter, and edge and group effects. The ultimate load results, failure modes, and influence on ultimate load are discussed.
- 1 December 2021
- Published by Elsevier in Engineering Structures
- Vol. 248
Influence of the flexural and shear reinforcement in the concrete cone resistance of headed bars
- 1 December 2021
- Published by Elsevier in Engineering Structures
- Vol. 248
Influence of the flexural and shear reinforcement in the concrete cone resistance of headed bars
- Open Access
- 1 January 2020
- Published by Editora Cubo
- p. 2250-2260
AVALIAÇÃO DO GRAU DE DETERIORAÇÃO DE OBRA DE ARTE ESPECIAL LOCALIZADA NA ÁREA CENTRAL DE BRASÍLIA / DF ESTUDO DE CASO
- 1 January 2020
- Published by Editora Cubo
- p. 2250-2260
Open AccessAVALIAÇÃO DO GRAU DE DETERIORAÇÃO DE OBRA DE ARTE ESPECIAL LOCALIZADA NA ÁREA CENTRAL DE BRASÍLIA / DF ESTUDO DE CASO
- 1 May 2013
- Published by Elsevier in IFAC Proceedings Volumes
- Vol. 46 (7) , 456-461
Proposal of a Fuzzy Control System for the Management of Traffic lights
- 1 May 2013
- Published by Elsevier in IFAC Proceedings Volumes
- Vol. 46 (7) , 456-461
Proposal of a Fuzzy Control System for the Management of Traffic lights