Natchanai Roongmuanpha
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Natchanai Roongmuanpha has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Worapong Tangsrirat
School of Engineering, King Mongkut’s Institute of Technology Ladkrabang (KMITL), Bangkok 10520, Thailand
20 shared publications - Tattaya Pukkalanun
School of Engineering, King Mongkut’s Institute of Technology Ladkrabang (KMITL), Bangkok 10520, Thailand
14 shared publications - Mohammad Faseehuddin
Thapar Institute of Engineering and Technology
7 shared publications - Jetsdaporn Satansup
Rajamangala University of Technology Rattanakosin
3 shared publications - Napasool Wongvanich
King Mongkut’s Institute of Technology Ladkrabang
3 shared publications - Nutcha Likhitkitwoerakul
Ministry of Natural Resources and Environment, Bangkok 10400, Thailand
2 shared publications
Latest Publications
- Open Access
- 12 October 2026
- Published by Elsevier in Results in Engineering
- Vol. 32
Integer- and fractional-order inductance simulators based on only a single DDGA and a grounded capacitor
- 12 October 2026
- Published by Elsevier in Results in Engineering
- Vol. 32
Open AccessInteger- and fractional-order inductance simulators based on only a single DDGA and a grounded capacitor
- Open Access
- 2 September 2026
- Published by Elsevier in SSRN Electronic Journal
Integer- and Fractional-Order Inductance Simulators Based on Only a Single DDGA and a Grounded Capacitor
This paper presents the design of an electronically tunable fractional-order inductor (FOI) simulator capable of realizing lossy (series and parallel types) and lossless configurations within a single topology. The proposed circuit employs only a single differential differencing gain amplifier (DDGA) and a single grounded capacitor, making it highly suitable for integrated circuit implementation. By replacing the conventional capacitor with a fractional-order capacitor, the proposed simulator effectively emulates the characteristics of fractional-order inductors. Key parameters, including the equivalent inductance, equivalent resistance, and the fractional equivalent inductance, can be electronically adjusted through the transconductance gain of the DDGA. The performance and functionality of the proposed simulators are validated through PSPICE simulations using 180-nm CMOS technology parameters, which demonstrate excellent agreement with theoretical analyses. Furthermore, the practical utility of the proposed integer- and fractional-order inductor simulators is illustrated through several application circuits. These circuits include current-mode (CM), transimpedance-mode (TIM), voltage-mode (VM), and transadmittance-mode (TAM) highpass filters, as well as VM and TAM inverse lowpass filters, parasitic resistance cancellation, a sinusoidal oscillator, and a fractional-order highpass filter that employs the proposed FOI.
- 2 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessInteger- and Fractional-Order Inductance Simulators Based on Only a Single DDGA and a Grounded Capacitor
This paper presents the design of an electronically tunable fractional-order inductor (FOI) simulator capable of realizing lossy (series and parallel types) and lossless configurations within a single topology. The proposed circuit employs only a single differential differencing gain amplifier (DDGA) and a single grounded capacitor, making it highly suitable for integrated circuit implementation. By replacing the conventional capacitor with a fractional-order capacitor, the proposed simulator effectively emulates the characteristics of fractional-order inductors. Key parameters, including the equivalent inductance, equivalent resistance, and the fractional equivalent inductance, can be electronically adjusted through the transconductance gain of the DDGA. The performance and functionality of the proposed simulators are validated through PSPICE simulations using 180-nm CMOS technology parameters, which demonstrate excellent agreement with theoretical analyses. Furthermore, the practical utility of the proposed integer- and fractional-order inductor simulators is illustrated through several application circuits. These circuits include current-mode (CM), transimpedance-mode (TIM), voltage-mode (VM), and transadmittance-mode (TAM) highpass filters, as well as VM and TAM inverse lowpass filters, parasitic resistance cancellation, a sinusoidal oscillator, and a fractional-order highpass filter that employs the proposed FOI.
- Open Access
- 15 April 2026
- Published by MDPI AG in Electronics
- Vol. 15 (8) , 1663
VDTA-Based Mixed-Mode Inverse Filter and Its Application to Mixed-Mode PID Controller
This paper presents a novel voltage differencing transconductance amplifier (VDTA)-based mixed-mode inverse filter capable of operating in voltage mode, transadmittance mode, transimpedance mode, and current mode using a single topology. The proposed configuration employs only three VDTAs with two resistors and three capacitors, offering low component count, high input/output impedance flexibility, and no requirement for component matching. It simultaneously realizes first-order inverse lowpass and highpass, as well as second-order inverse bandpass responses. A comprehensive non-ideal analysis, which includes the effects of VDTA parasitic impedances, determines the practical operating frequency range. The design is validated through PSPICE simulations using 0.18 μm CMOS technology, showing close alignment between theoretical predictions and simulation results, with cutoff frequencies of approximately 1.60 MHz and low power consumption of 0.972 mW. Further analyses confirm orthogonal tuning capability, acceptable temperature stability, and robustness against component tolerances. In a practical application, the proposed inverse filter is employed to implement a mixed-mode PID controller, which significantly improves transient response characteristics by reducing rise time, settling time, and steady-state error. These findings highlight the effectiveness and versatility of the proposed design for analog signal processing and control system applications.
- 15 April 2026
- Published by MDPI AG in Electronics
- Vol. 15 (8) , 1663
Open AccessVDTA-Based Mixed-Mode Inverse Filter and Its Application to Mixed-Mode PID Controller
This paper presents a novel voltage differencing transconductance amplifier (VDTA)-based mixed-mode inverse filter capable of operating in voltage mode, transadmittance mode, transimpedance mode, and current mode using a single topology. The proposed configuration employs only three VDTAs with two resistors and three capacitors, offering low component count, high input/output impedance flexibility, and no requirement for component matching. It simultaneously realizes first-order inverse lowpass and highpass, as well as second-order inverse bandpass responses. A comprehensive non-ideal analysis, which includes the effects of VDTA parasitic impedances, determines the practical operating frequency range. The design is validated through PSPICE simulations using 0.18 μm CMOS technology, showing close alignment between theoretical predictions and simulation results, with cutoff frequencies of approximately 1.60 MHz and low power consumption of 0.972 mW. Further analyses confirm orthogonal tuning capability, acceptable temperature stability, and robustness against component tolerances. In a practical application, the proposed inverse filter is employed to implement a mixed-mode PID controller, which significantly improves transient response characteristics by reducing rise time, settling time, and steady-state error. These findings highlight the effectiveness and versatility of the proposed design for analog signal processing and control system applications.
- Open Access
- 4 February 2026
- Published by MDPI AG in Technologies
- Vol. 14 (2) , 101
Single VDCC-Based Mixed-Mode First-Order Universal Filter and Applications in Bio-Signal Processing Systems
This paper presents a compact mixed-mode first-order universal filter based on a single voltage differencing current conveyor (VDCC), which can function in all four possible operation modes, i.e., voltage mode (VM), trans-admittance mode (TAM), current mode (CM), and trans-impedance mode (TIM). The proposed configuration requires only two grounded resistors and one floating capacitor, which contributes to a low component count, facilitates integration, and allows for the electronic tunability of the pole frequency through the transconductance gain of the VDCC. This work also demonstrates two practical biomedical applications: an electrocardiogram (ECG) acquisition system utilizing the VM low-pass filter for noise suppression and a bioimpedance (BioZ) measurement system employing the proposed configuration-based CM oscillator circuit as a sinusoidal excitation source. The performance validation confirms the accuracy of impedance extraction and the preservation of waveforms using tissue-equivalent models. The results demonstrate that the proposed VDCC-based filter offers a compact, power-efficient, and versatile analog signal-processing solution suitable for modern biomedical instrumentation.
- 4 February 2026
- Published by MDPI AG in Technologies
- Vol. 14 (2) , 101
Open AccessSingle VDCC-Based Mixed-Mode First-Order Universal Filter and Applications in Bio-Signal Processing Systems
This paper presents a compact mixed-mode first-order universal filter based on a single voltage differencing current conveyor (VDCC), which can function in all four possible operation modes, i.e., voltage mode (VM), trans-admittance mode (TAM), current mode (CM), and trans-impedance mode (TIM). The proposed configuration requires only two grounded resistors and one floating capacitor, which contributes to a low component count, facilitates integration, and allows for the electronic tunability of the pole frequency through the transconductance gain of the VDCC. This work also demonstrates two practical biomedical applications: an electrocardiogram (ECG) acquisition system utilizing the VM low-pass filter for noise suppression and a bioimpedance (BioZ) measurement system employing the proposed configuration-based CM oscillator circuit as a sinusoidal excitation source. The performance validation confirms the accuracy of impedance extraction and the preservation of waveforms using tissue-equivalent models. The results demonstrate that the proposed VDCC-based filter offers a compact, power-efficient, and versatile analog signal-processing solution suitable for modern biomedical instrumentation.
- 23 January 2026
- Published by Springer Nature
- p. 29-37
Design and Synthesis of Capacitance Multiplier Using LT1228s and a Grounded Capacitor
- 23 January 2026
- Published by Springer Nature
- p. 29-37
Design and Synthesis of Capacitance Multiplier Using LT1228s and a Grounded Capacitor
- Open Access
- 1 January 2026
- Published by Wiley in Journal of Engineering
- Vol. 2026 (1)
Grounded Series and Parallel RL/RC Immittance Simulators Using a Single Second‐Generation Voltage Conveyor
This work proposes the active simulation of grounded series and parallel resistive‐inductive (RL) and resistive‐capacitive (RC) immittance functions employing a single second‐generation voltage conveyor (VCII) and three passive components. The two configurations are designed for series RL and RC immittance simulation and RL and parallel RC immittance simulation, respectively. All of the simulated immittance functions can be realized without any specific component matching or cancellation limitations. The proposed series and parallel RL and RC immittance function simulators have been simulated with PSPICE program based on 0.18 µm CMOS process parameters to validate the theoretical study. The first‐order inverse filters, biquadratic filter, and synthetic lossless inductor applications, constructed with the proposed simulator circuits, are designed and evaluated to further demonstrate the practical usefulness of the designed simulators.
- 1 January 2026
- Published by Wiley in Journal of Engineering
- Vol. 2026 (1)
Open AccessGrounded Series and Parallel RL/RC Immittance Simulators Using a Single Second‐Generation Voltage Conveyor
This work proposes the active simulation of grounded series and parallel resistive‐inductive (RL) and resistive‐capacitive (RC) immittance functions employing a single second‐generation voltage conveyor (VCII) and three passive components. The two configurations are designed for series RL and RC immittance simulation and RL and parallel RC immittance simulation, respectively. All of the simulated immittance functions can be realized without any specific component matching or cancellation limitations. The proposed series and parallel RL and RC immittance function simulators have been simulated with PSPICE program based on 0.18 µm CMOS process parameters to validate the theoretical study. The first‐order inverse filters, biquadratic filter, and synthetic lossless inductor applications, constructed with the proposed simulator circuits, are designed and evaluated to further demonstrate the practical usefulness of the designed simulators.
- Open Access
- 1 September 2025
- Published by MDPI AG in Technologies
- Vol. 13 (9) , 393
All-Grounded Passive Component Mixed-Mode Multifunction Biquadratic Filter and Dual-Mode Quadrature Oscillator Employing a Single Active Element
This paper introduces a compact analog configuration that concurrently realizes a mixed-mode biquadratic filter and a dual-mode quadrature oscillator (QO) by employing a single differential differencing gain amplifier (DDGA) and all-grounded passive components. The proposed design supports four fundamental operation modes—voltage-mode (VM), current-mode (CM), trans-impedance-mode (TIM), and trans-admittance-mode (TAM)—utilizing the same circuit topology without structural modifications. In filter operation, it offers low-pass, high-pass, band-pass, band-stop, and all-pass responses with orthogonal and electronic pole frequency and quality factor. In oscillator operation, it delivers simultaneous voltage and current quadrature outputs with independent tuning of oscillator frequency and condition. The grounded-component configuration simplifies layout and enhances its suitability for monolithic integration. Numerical simulations in a 0.18-μm CMOS process with ±0.9 V supply confirm theoretical predictions, demonstrating precise gain-phase characteristics, low total harmonic distortion (<7%), modest sensitivity to 5% component variations, and stable operation from −40 °C to 120 °C. These results, combined with the circuit’s low component count and integration suitability, suggest strong potential for future development in low-power IoT devices, adaptive communication front-ends, and integrated biomedical systems.
- 1 September 2025
- Published by MDPI AG in Technologies
- Vol. 13 (9) , 393
Open AccessAll-Grounded Passive Component Mixed-Mode Multifunction Biquadratic Filter and Dual-Mode Quadrature Oscillator Employing a Single Active Element
This paper introduces a compact analog configuration that concurrently realizes a mixed-mode biquadratic filter and a dual-mode quadrature oscillator (QO) by employing a single differential differencing gain amplifier (DDGA) and all-grounded passive components. The proposed design supports four fundamental operation modes—voltage-mode (VM), current-mode (CM), trans-impedance-mode (TIM), and trans-admittance-mode (TAM)—utilizing the same circuit topology without structural modifications. In filter operation, it offers low-pass, high-pass, band-pass, band-stop, and all-pass responses with orthogonal and electronic pole frequency and quality factor. In oscillator operation, it delivers simultaneous voltage and current quadrature outputs with independent tuning of oscillator frequency and condition. The grounded-component configuration simplifies layout and enhances its suitability for monolithic integration. Numerical simulations in a 0.18-μm CMOS process with ±0.9 V supply confirm theoretical predictions, demonstrating precise gain-phase characteristics, low total harmonic distortion (<7%), modest sensitivity to 5% component variations, and stable operation from −40 °C to 120 °C. These results, combined with the circuit’s low component count and integration suitability, suggest strong potential for future development in low-power IoT devices, adaptive communication front-ends, and integrated biomedical systems.
- Open Access
- 12 February 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (4) , 1916
Cascadable First-Order and Second-Order Inverse Filters Based on Second-Generation Voltage Conveyors
This study introduces four novel configurations of first-order and second-order multifunction inverse filters in both voltage-mode (VM) and current-mode (CM) using second-generation voltage conveyors (VCIIs). The first-order VM and CM inverse filters utilize only three passive components together with one VCII for VM and two VCIIs for CM realizations, which can provide lowpass and highpass inverse filter responses. The latter, second-order VM and CM multifunction inverse filters, can be constructed using the corresponding first-order inverse filters as their core circuits. These filters offer all the basic inverse filter functions, including lowpass, bandpass, and highpass inverse responses with all gains obtained from the same design. All the inverse filter realizations are cascadable. No component matching requirements are necessary for all filter responses. The non-ideal effects of the VCII on the performance of the proposed inverse filters are thoroughly examined. To prove the feasibility of the designs, the PSPICE program performed several simulations, utilizing model parameters of 0.18 µm CMOS technology. Some testing experiments were conducted using the commercially available IC-type AD844s for evaluating the practical performance of the designed inverse filters.
- 12 February 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (4) , 1916
Open AccessCascadable First-Order and Second-Order Inverse Filters Based on Second-Generation Voltage Conveyors
This study introduces four novel configurations of first-order and second-order multifunction inverse filters in both voltage-mode (VM) and current-mode (CM) using second-generation voltage conveyors (VCIIs). The first-order VM and CM inverse filters utilize only three passive components together with one VCII for VM and two VCIIs for CM realizations, which can provide lowpass and highpass inverse filter responses. The latter, second-order VM and CM multifunction inverse filters, can be constructed using the corresponding first-order inverse filters as their core circuits. These filters offer all the basic inverse filter functions, including lowpass, bandpass, and highpass inverse responses with all gains obtained from the same design. All the inverse filter realizations are cascadable. No component matching requirements are necessary for all filter responses. The non-ideal effects of the VCII on the performance of the proposed inverse filters are thoroughly examined. To prove the feasibility of the designs, the PSPICE program performed several simulations, utilizing model parameters of 0.18 µm CMOS technology. Some testing experiments were conducted using the commercially available IC-type AD844s for evaluating the practical performance of the designed inverse filters.
- Open Access
- 31 January 2025
- Published by OU Scientific Route in EUREKA: Physics and Engineering
- No. 1,p. 75-83
Low-voltage temperature-insensitive logarithmic and exponential function current generators using only npn transistors
The continuing reduction of supply voltage for reliable operation of analog integrated circuits is widely recognized. Analog circuits must adhere to this trend. As a result, researchers are currently developing low-voltage analog circuit methodologies. Current-mode signal processing circuits are examples of these concepts. Therefore, the objective of this work is to present circuit realizations of low-voltage current-mode logarithmic and exponential function generators with temperature compensation. Both the input and output signals operate in current mode. The design approach utilizes the current-mode translinear technique to produce the output currents that exhibit a directly proportionality to the absolute values of the logarithmic and exponential functions. By simply adjusting the external bias currents, one can electronically tune the output currents and transfer current gains for both proposed circuits. The proposed circuits utilize only npn bipolar transistors and can operate with low-level supply voltages of ±1V, which are appropriate for low-power, high-frequency applications. Nonideality performance considerations are also discussed in detail. In order to verify the operational function of the circuits and illustrate their superior thermal stability, the PSPICE simulation has been performed using real transistor models provided for the HFA3096 mixed bipolar array technology. The simulation findings illustrate that the proposed logarithmic and exponential amplifier circuits can compensate for temperature variations, as evidenced by the good stability of their output currents over a temperature range of -40 °C to 100 °C.
- 31 January 2025
- Published by OU Scientific Route in EUREKA: Physics and Engineering
- No. 1,p. 75-83
Open AccessLow-voltage temperature-insensitive logarithmic and exponential function current generators using only npn transistors
The continuing reduction of supply voltage for reliable operation of analog integrated circuits is widely recognized. Analog circuits must adhere to this trend. As a result, researchers are currently developing low-voltage analog circuit methodologies. Current-mode signal processing circuits are examples of these concepts. Therefore, the objective of this work is to present circuit realizations of low-voltage current-mode logarithmic and exponential function generators with temperature compensation. Both the input and output signals operate in current mode. The design approach utilizes the current-mode translinear technique to produce the output currents that exhibit a directly proportionality to the absolute values of the logarithmic and exponential functions. By simply adjusting the external bias currents, one can electronically tune the output currents and transfer current gains for both proposed circuits. The proposed circuits utilize only npn bipolar transistors and can operate with low-level supply voltages of ±1V, which are appropriate for low-power, high-frequency applications. Nonideality performance considerations are also discussed in detail. In order to verify the operational function of the circuits and illustrate their superior thermal stability, the PSPICE simulation has been performed using real transistor models provided for the HFA3096 mixed bipolar array technology. The simulation findings illustrate that the proposed logarithmic and exponential amplifier circuits can compensate for temperature variations, as evidenced by the good stability of their output currents over a temperature range of -40 °C to 100 °C.
- Open Access
- 14 January 2025
- Published by MDPI AG in Preprints.org
Cascadable First-Order and Second-Order Inverse Filters Based On Second-Generation Voltage Conveyors
This study introduces four novel configurations of first-order and second-order multifunction inverse filters in both voltage-mode (VM) and current-mode (CM) using second-generation voltage conveyors (VCIIs). The first-order VM and CM inverse filters utilize only three passive components together with one VCII for VM and two VCIIs for CM realizations, which can provide lowpass (LP) and highpass (HP) inverse filter responses through appropriate impedance selections. The latter, second-order VM and CM multifunction inverse filters, can be constructed using the corresponding first-order inverse filters as their core circuits. These filters offer all the basic inverse filter functions, including LP, bandpass (BP), and HP inverse responses with all gains obtained from the same design. All the CM inverse filter realizations possess low-input and high-output impedances, enabling them to be fully cascaded in CM operation. For the VM filter realizations, they exhibit low-output impedances, which directly connect to the next stage without any buffer requirement. No component matching requirements are necessary for all filter responses. The non-ideal effects of the VCII on the performance of the proposed inverse filters are thoroughly examined, taking into account undesirable aspects such as tracking errors and parasitic impedances. To prove the feasibility of the designs, PSPICE program performed several simulations, utilizing model parameters of 0.18-µm CMOS technology. In addition, some testing experiments are conducted using the commercially available IC-type AD844s for evaluating the practical performance of the designed inverse filters.
- 14 January 2025
- Published by MDPI AG in Preprints.org
Open AccessCascadable First-Order and Second-Order Inverse Filters Based On Second-Generation Voltage Conveyors
This study introduces four novel configurations of first-order and second-order multifunction inverse filters in both voltage-mode (VM) and current-mode (CM) using second-generation voltage conveyors (VCIIs). The first-order VM and CM inverse filters utilize only three passive components together with one VCII for VM and two VCIIs for CM realizations, which can provide lowpass (LP) and highpass (HP) inverse filter responses through appropriate impedance selections. The latter, second-order VM and CM multifunction inverse filters, can be constructed using the corresponding first-order inverse filters as their core circuits. These filters offer all the basic inverse filter functions, including LP, bandpass (BP), and HP inverse responses with all gains obtained from the same design. All the CM inverse filter realizations possess low-input and high-output impedances, enabling them to be fully cascaded in CM operation. For the VM filter realizations, they exhibit low-output impedances, which directly connect to the next stage without any buffer requirement. No component matching requirements are necessary for all filter responses. The non-ideal effects of the VCII on the performance of the proposed inverse filters are thoroughly examined, taking into account undesirable aspects such as tracking errors and parasitic impedances. To prove the feasibility of the designs, PSPICE program performed several simulations, utilizing model parameters of 0.18-µm CMOS technology. In addition, some testing experiments are conducted using the commercially available IC-type AD844s for evaluating the practical performance of the designed inverse filters.