Hyang Mi Yu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hyang Mi Yu has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Byeong Geun Jeong
Department of Energy Science, Sungkyunkwan University, Suwon 16419, Korea
2 shared publications - Dae Young Park
Department of Physics, Hanyang University, Seoul 04763, Republic of Korea
2 shared publications - Mun Seok Jeong
Hanyang University
2 shared publications - Gon Namkoong
Old Dominion University
1 shared publication - Seong Chu Lim
Department of Energy Science, Sungkyunkwan University, Suwon 16419, Republic of Korea
1 shared publication - Sung Hyuk Kim
Department of Energy Science, Sungkyunkwan University, Suwon 16419, Korea
1 shared publication
Latest Publications
- Open Access
Investigation of Cation Exchange Behaviors of FAxMA1−xPbI3 Films Using Dynamic Spin-Coating
In this study, we fabricated and characterized uniform multi-cation perovskite FAxMA1−xPbI3 films. We used the dynamic spin-coating method to control the cation ratio of the film by gradually increasing the FA+, which replaced the MA+ in the films. When the FA+ concentration was lower than xFA ~0.415 in the films, the stability of the multi-cation perovskite improved. Above this concentration, the film exhibited δ-phase FAPbI3 in the FAxMA1−xPbI3 films. The formation of δ-phase FAPbI3 disturbed the homogeneity of the photoluminescence spatial distribution and suppressed the absorption spectral bandwidth with the increasing bandgap. The precise control of the cation ratio of multi-cation perovskite films is necessary to optimize the energy-harvesting performance.
Open AccessInvestigation of Cation Exchange Behaviors of FAxMA1−xPbI3 Films Using Dynamic Spin-Coating
In this study, we fabricated and characterized uniform multi-cation perovskite FAxMA1−xPbI3 films. We used the dynamic spin-coating method to control the cation ratio of the film by gradually increasing the FA+, which replaced the MA+ in the films. When the FA+ concentration was lower than xFA ~0.415 in the films, the stability of the multi-cation perovskite improved. Above this concentration, the film exhibited δ-phase FAPbI3 in the FAxMA1−xPbI3 films. The formation of δ-phase FAPbI3 disturbed the homogeneity of the photoluminescence spatial distribution and suppressed the absorption spectral bandwidth with the increasing bandgap. The precise control of the cation ratio of multi-cation perovskite films is necessary to optimize the energy-harvesting performance.
- Open Access
- 15 October 2021
- Published by MDPI AG in Nanomaterials
- Vol. 11 (10) , 2735
Nano-Thermal Analysis of Defect-Induced Surface Pre-Melting in 2D Tellurium
Thermal properties, such as thermal conductivity, heat capacity, and melting temperature, influence the efficiency and stability of two-dimensional (2D) material applications. However, existing studies on thermal characteristics—except for thermal conductivity—are insufficient for 2D materials. Here, we investigated the melting temperature of 2D Tellurium (2D Te) using the nano-thermal analysis technique and found anomalous behavior that occurs before the melting temperature is reached. The theoretical calculations present surface pre-melting in 2D Te and Raman scattering measurements suggest that defects in 2D Te accelerate surface pre-melting. Understanding the pre-melting surface characteristics of 2D Te will provide valuable information for practical applications.
- 15 October 2021
- Published by MDPI AG in Nanomaterials
- Vol. 11 (10) , 2735
Open AccessNano-Thermal Analysis of Defect-Induced Surface Pre-Melting in 2D Tellurium
Thermal properties, such as thermal conductivity, heat capacity, and melting temperature, influence the efficiency and stability of two-dimensional (2D) material applications. However, existing studies on thermal characteristics—except for thermal conductivity—are insufficient for 2D materials. Here, we investigated the melting temperature of 2D Tellurium (2D Te) using the nano-thermal analysis technique and found anomalous behavior that occurs before the melting temperature is reached. The theoretical calculations present surface pre-melting in 2D Te and Raman scattering measurements suggest that defects in 2D Te accelerate surface pre-melting. Understanding the pre-melting surface characteristics of 2D Te will provide valuable information for practical applications.