Darryl J. Mohr
Research Subjects
Darryl J. Mohr has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Eric L. Petersen
Texas A&M University
4 shared publications - Claire M. Grégoire
J Mike Walker ’66 Department of Mechanical Engineering Texas A&M University Texas USA
3 shared publications - Olivier Mathieu
Texas A&M University
3 shared publications - Sean P. Cooper
J. Mike Walker '66 Department of Mechanical Engineering, Texas A&M University, College Station, TX 77843
2 shared publications - Sulaiman Abdulaziz Alturaifi
Mechanical Engineering King Fahd University of Petroleum & Minerals Dhahran 23953 Saudi Arabia
2 shared publications - Laurent Catoire
ICARE-CNRS and University of Orleans, 1C, avenue de la Recherche Scientifique, 45071 Orleans cedex 2, France
1 shared publication
Latest Publications
- 1 January 2025
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 96 (1)
An improved endwall-injection technique for examining high-temperature ignition of lubricating oils in shock tubes
Ignition of the lubricating fluid in a mechanical system is a highly undesirable and unsafe condition that can arise from the elevated temperatures and pressures to which the lubricant is subjected. It is therefore important to understand the fundamental chemistry behind its ignition to predict and prevent this condition. Lubricating oils, particularly those with a mineral oil base, are very complex mixtures of thousands of hydrocarbons. Additionally, these oils have very low vapor pressures and high viscosities. These physical characteristics present considerable barriers to examining and understanding lubricant ignition chemistry. Therefore, a novel experimental design was devised to create and introduce a lubricant aerosol into a shock-tube facility in a reliable yet relatively simple manner. In this way, the lubricant can be quasi-homogeneously introduced into the shock tube where it will be vaporized by the incident shock wave, and combustion can be observed behind the reflected shock wave. To characterize the technique and anchor it with previously established methods, n-hexadecane was chosen to be tested both with the endwall injection and the well-established, heated shock tube techniques. This comparison showed good agreement, proving the ability of the simple technique to produce reliable ignition delay time (IDT) results. From here, Jet-A was also tested with the current injection technique and compared to a previous generation of the technique to highlight the advantages of the present method. Then, IDT results for mineral oil were collected to establish a baseline IDT set to which off-the-shelf lubricants and additional mixtures can be compared. Finally, IDTs for the off-the-shelf, mineral-based lubricant Mobil DTE 732 were obtained and compared to the baseline as well as the n-hexadecane results. All experiments were conducted near atmospheric pressure and for temperatures between 1084 and 1530 K. An analysis of the system estimated the effective stoichiometry to be around ϕ = 1.15. Although no kinetics mechanisms exist for lubrication oils, preliminary model predictions made by modern chemical kinetics mechanisms for an alkane with 16 carbon atoms were then compared to the results to elucidate some of the chemistry this new method will allow the community to probe. This paper establishes the new method as a viable way to study and compare the ignition behavior of lubricating oils and other very low-vapor-pressure fuels in a shock tube.
- 1 January 2025
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 96 (1)
An improved endwall-injection technique for examining high-temperature ignition of lubricating oils in shock tubes
Ignition of the lubricating fluid in a mechanical system is a highly undesirable and unsafe condition that can arise from the elevated temperatures and pressures to which the lubricant is subjected. It is therefore important to understand the fundamental chemistry behind its ignition to predict and prevent this condition. Lubricating oils, particularly those with a mineral oil base, are very complex mixtures of thousands of hydrocarbons. Additionally, these oils have very low vapor pressures and high viscosities. These physical characteristics present considerable barriers to examining and understanding lubricant ignition chemistry. Therefore, a novel experimental design was devised to create and introduce a lubricant aerosol into a shock-tube facility in a reliable yet relatively simple manner. In this way, the lubricant can be quasi-homogeneously introduced into the shock tube where it will be vaporized by the incident shock wave, and combustion can be observed behind the reflected shock wave. To characterize the technique and anchor it with previously established methods, n-hexadecane was chosen to be tested both with the endwall injection and the well-established, heated shock tube techniques. This comparison showed good agreement, proving the ability of the simple technique to produce reliable ignition delay time (IDT) results. From here, Jet-A was also tested with the current injection technique and compared to a previous generation of the technique to highlight the advantages of the present method. Then, IDT results for mineral oil were collected to establish a baseline IDT set to which off-the-shelf lubricants and additional mixtures can be compared. Finally, IDTs for the off-the-shelf, mineral-based lubricant Mobil DTE 732 were obtained and compared to the baseline as well as the n-hexadecane results. All experiments were conducted near atmospheric pressure and for temperatures between 1084 and 1530 K. An analysis of the system estimated the effective stoichiometry to be around ϕ = 1.15. Although no kinetics mechanisms exist for lubrication oils, preliminary model predictions made by modern chemical kinetics mechanisms for an alkane with 16 carbon atoms were then compared to the results to elucidate some of the chemistry this new method will allow the community to probe. This paper establishes the new method as a viable way to study and compare the ignition behavior of lubricating oils and other very low-vapor-pressure fuels in a shock tube.
- Open Access
An Experimental and Detailed Kinetics Modeling Study of Norbornadiene in Hydrogen and Methane Mixtures: Ignition Delay Time and Spectroscopic CO Measurements
High-energy-density compounds such as norbornadiene (NBD) are being considered as potential cost-effective fuel additives, or partial replacements, for high-speed propulsion applications. To assess the ability of NBD to influence basic fuel reactivity enhancement and to build a database for developing future NBD kinetics models, ignition delay times were measured in two shock-tube facilities at Texas A&M University for H2/O2, CH4/O2, H2/NBD/O2, and CH4/NBD/O2 mixtures (ϕ = 1) that were highly diluted in argon. The reflected-shock temperatures ranged from 1014 to 2227 K, and the reflected-shock pressures remained near 1 atm for all of the experiments, apart from the hydrogen mixtures, which were also tested near 7 atm, targeting the second-explosion limit. The molar concentrations of NBD were supplemented to the baseline mixtures representing 1–2% of the fuel by volume. A chemiluminescence diagnostic was used to track the time history of excited hydroxyl radical (OH*) emission, which was used to define the ignition delay time at the sidewall location. Spectroscopic CO data were also obtained using a tunable quantum cascade laser to complement both the ignition and the chemiluminescence data. The CH4/O2 mixtures containing NBD demonstrated reduced ignition delay times, with a pronounced effect at lower temperatures. Conversely, this additive increased the ignition delay time dramatically in the H2/O2 mixture, which was attributed to changes in the fundamental chemistry with the introduction of molecules containing carbon bonds, which require stronger activation energies for ignition. Correlations were developed to predict the ignition delay time, which depends on species concentration, temperature, and pressure. Additionally, one tentative mechanism was tested, combining base chemistry from NUIGMech 1.1 with pyrolysis and oxidation reactions for NBD using the recent efforts from experimental and theoretical literature studies. The numerical predictions show that the rapid decomposition of NBD provides a pool of active H-radicals, significantly increasing the reactivity of methane. This study represents the first set of gas-phase ignition and CO time-history data measured in a shock tube for hydrogen and methane mixtures containing the additive NBD.
Open AccessAn Experimental and Detailed Kinetics Modeling Study of Norbornadiene in Hydrogen and Methane Mixtures: Ignition Delay Time and Spectroscopic CO Measurements
High-energy-density compounds such as norbornadiene (NBD) are being considered as potential cost-effective fuel additives, or partial replacements, for high-speed propulsion applications. To assess the ability of NBD to influence basic fuel reactivity enhancement and to build a database for developing future NBD kinetics models, ignition delay times were measured in two shock-tube facilities at Texas A&M University for H2/O2, CH4/O2, H2/NBD/O2, and CH4/NBD/O2 mixtures (ϕ = 1) that were highly diluted in argon. The reflected-shock temperatures ranged from 1014 to 2227 K, and the reflected-shock pressures remained near 1 atm for all of the experiments, apart from the hydrogen mixtures, which were also tested near 7 atm, targeting the second-explosion limit. The molar concentrations of NBD were supplemented to the baseline mixtures representing 1–2% of the fuel by volume. A chemiluminescence diagnostic was used to track the time history of excited hydroxyl radical (OH*) emission, which was used to define the ignition delay time at the sidewall location. Spectroscopic CO data were also obtained using a tunable quantum cascade laser to complement both the ignition and the chemiluminescence data. The CH4/O2 mixtures containing NBD demonstrated reduced ignition delay times, with a pronounced effect at lower temperatures. Conversely, this additive increased the ignition delay time dramatically in the H2/O2 mixture, which was attributed to changes in the fundamental chemistry with the introduction of molecules containing carbon bonds, which require stronger activation energies for ignition. Correlations were developed to predict the ignition delay time, which depends on species concentration, temperature, and pressure. Additionally, one tentative mechanism was tested, combining base chemistry from NUIGMech 1.1 with pyrolysis and oxidation reactions for NBD using the recent efforts from experimental and theoretical literature studies. The numerical predictions show that the rapid decomposition of NBD provides a pool of active H-radicals, significantly increasing the reactivity of methane. This study represents the first set of gas-phase ignition and CO time-history data measured in a shock tube for hydrogen and methane mixtures containing the additive NBD.
- 31 August 2022
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 39 (1) , 499-510
Experimental and detailed kinetics modeling study of the fire suppressant properties of di(2,2,2trifluoroethyl) carbonate
- 31 August 2022
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 39 (1) , 499-510
Experimental and detailed kinetics modeling study of the fire suppressant properties of di(2,2,2trifluoroethyl) carbonate
- Open Access
An Experimental Kinetics Study of Isopropanol Pyrolysis and Oxidation behind Reflected Shock Waves
Isopropanol has potential as a future bio-derived fuel and is a promising substitute for ethanol in gasoline blends. Even so, little has been done in terms of high-temperature chemical kinetic speciation studies of this molecule. To this end, experiments were conducted in a shock tube using simultaneous CO and H2O laser absorption measurements. Water and CO formation during isopropanol pyrolysis was also examined at temperatures between 1127 and 2162 K at an average pressure of 1.42 atm. Species profiles were collected at temperatures between 1332 and 1728 K and at an average pressure of 1.26 atm for equivalence ratios of 0.5, 1.0, and 2.0 in highly diluted mixtures of 20% helium and 79.5% argon. Species profiles were also compared to four modern C3 alcohol mechanisms, including the impact of recent rate constant measurements. The Li et al. (2019) and Saggese et al. (2021) models both best predict CO and water production under pyrolysis conditions, while the AramcoMech 3.0 and Capriolo and Konnov models better predict the oxidation experimental profiles. Additionally, previous studies have collected ignition delay time (τign) data for isopropanol but are limited to low pressures in highly dilute mixtures. Therefore, real fuel–air experiments were conducted in a heated shock tube with isopropanol for stoichiometric and lean conditions at 10 and 25 atm between 942 and 1428 K. Comparisons to previous experimental results highlight the need for real fuel–air experiments and proper interpretation of shock-tube data. The AramcoMech 3.0 model over predicts τign values, while the Li et al. model severely under predicts τign. The models by Capriolo and Konnov and Saggese et al. show good agreement with experimental τign values. A sensitivity analysis using these two models highlights the underlying chemistry for isopropanol combustion at 25 atm. Additionally, modifying the Li et al. model with a recently measured reaction rate shows improvement in the model’s ability to predict CO and water profiles during dilute oxidation. Finally, a regression analysis was performed to quantify τign results from this study.
Open AccessAn Experimental Kinetics Study of Isopropanol Pyrolysis and Oxidation behind Reflected Shock Waves
Isopropanol has potential as a future bio-derived fuel and is a promising substitute for ethanol in gasoline blends. Even so, little has been done in terms of high-temperature chemical kinetic speciation studies of this molecule. To this end, experiments were conducted in a shock tube using simultaneous CO and H2O laser absorption measurements. Water and CO formation during isopropanol pyrolysis was also examined at temperatures between 1127 and 2162 K at an average pressure of 1.42 atm. Species profiles were collected at temperatures between 1332 and 1728 K and at an average pressure of 1.26 atm for equivalence ratios of 0.5, 1.0, and 2.0 in highly diluted mixtures of 20% helium and 79.5% argon. Species profiles were also compared to four modern C3 alcohol mechanisms, including the impact of recent rate constant measurements. The Li et al. (2019) and Saggese et al. (2021) models both best predict CO and water production under pyrolysis conditions, while the AramcoMech 3.0 and Capriolo and Konnov models better predict the oxidation experimental profiles. Additionally, previous studies have collected ignition delay time (τign) data for isopropanol but are limited to low pressures in highly dilute mixtures. Therefore, real fuel–air experiments were conducted in a heated shock tube with isopropanol for stoichiometric and lean conditions at 10 and 25 atm between 942 and 1428 K. Comparisons to previous experimental results highlight the need for real fuel–air experiments and proper interpretation of shock-tube data. The AramcoMech 3.0 model over predicts τign values, while the Li et al. model severely under predicts τign. The models by Capriolo and Konnov and Saggese et al. show good agreement with experimental τign values. A sensitivity analysis using these two models highlights the underlying chemistry for isopropanol combustion at 25 atm. Additionally, modifying the Li et al. model with a recently measured reaction rate shows improvement in the model’s ability to predict CO and water profiles during dilute oxidation. Finally, a regression analysis was performed to quantify τign results from this study.