Celso Roman Junior
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Celso Roman Junior has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Ademir José Zattera
Battery and Energy Storage Laboratory (LABAT), Department of Materials Science, University of Caxias do Sul, Caxias do Sul 95070-560, Brazil
2 shared publications - Claudio Antônio Perottoni
Universidade de Caxias do Sul, Caxias do Sul - RS, 95070-560, Brazil
2 shared publications - Eduardo Thomazi
Federal Institute of Education, Science and Technology of Rio Grande do Sul (IFRS), Campus Caxias do Sul, Caxias do Sul, Brazil
2 shared publications - Janete Eunice Zorzi
Universidade de Caxias do Sul, Caxias do Sul, Brazil
2 shared publications - Thiago de Oliveira Gamba
School of Dentistry Federal University of Rio Grande do Sul, UFRGS Porto Alegre Brazil
2 shared publications - Cesar Liberato Petzhold
Instituto de Química, Universidade Federal do Rio Grande do Sul (UFRGS), Av. Bento Gonçalves - Agronomia, Porto Alegre, RS 90650-001, Brazil
1 shared publication
Latest Publications
- 14 November 2024
- Published by Wiley in Polymer Composites
- Vol. 46 (5) , 4743-4754
Mechanical properties of a laminated composite of aramid fabric and high‐density polyethylene films reinforced with calcium carbonate, montmorillonite, and graphene
Nanofillers incorporated into polymeric matrices have gained attention for enhancing the properties of materials, particularly nanocomposites, with improvements observed in mechanical and dynamic mechanical thermal properties. Among the nanofillers, calcium carbonate (NCC), montmorillonite‐type clays (MMT), and graphene nanoplatelets (GNP) are prominent. The novelty of this study lies in investigating the dynamic compression behavior using the split‐Hopkinson pressure bar (SHPB) method on laminated composites prepared with reinforced High‐density polyethylene (HDPE) films, including the hybrid effect of calcium carbonate with montmorillonite and calcium carbonate with graphene. The objective of this research is to evaluate the influence of incorporating 1% by mass of nanofillers in laminated composites made with aramid fabric interspersed with nanoreinforced HDPE films. The laminated composites were assessed through bending tests, SHPB, and dynamic mechanical thermal analysis (DMTA). In addition to the samples containing NCC, MMT, and GNP, hybrid samples were prepared by intercalating films containing each nanofiller. The mechanical properties increased by 44%, 48%, and 55% in flexural strength and 46%, 69%, and 88% in flexural modulus for the composites prepared with calcium carbonate, graphene, and the hybrid graphene/calcium carbonate films, concerning the composite containing HDPE film. Moreover, the samples containing HDPE film with 1% GNP demonstrated a 79% increase in toughness, while the hybrid sample, which contained interspersed films of HDPE with 1% GNP and 1% NCC, exhibited a 46% increase in toughness. These results indicate a superior toughness response under high strain rates, contributing to enhanced energy dissipation. These two samples exhibited highly potential for ballistic industrial applications.Highlights: Laminated composites reinforced with NCC, MMT, and GNP nanofillers. Mechanical properties of laminated composites assessed using the Split‐Hopkinson pressure bar test and dynamic mechanical thermal analysis. Impact strength improvement through the incorporation of nanofiller into laminated composites. Enhanced energy dissipation in laminated composite materials.
- 14 November 2024
- Published by Wiley in Polymer Composites
- Vol. 46 (5) , 4743-4754
Mechanical properties of a laminated composite of aramid fabric and high‐density polyethylene films reinforced with calcium carbonate, montmorillonite, and graphene
Nanofillers incorporated into polymeric matrices have gained attention for enhancing the properties of materials, particularly nanocomposites, with improvements observed in mechanical and dynamic mechanical thermal properties. Among the nanofillers, calcium carbonate (NCC), montmorillonite‐type clays (MMT), and graphene nanoplatelets (GNP) are prominent. The novelty of this study lies in investigating the dynamic compression behavior using the split‐Hopkinson pressure bar (SHPB) method on laminated composites prepared with reinforced High‐density polyethylene (HDPE) films, including the hybrid effect of calcium carbonate with montmorillonite and calcium carbonate with graphene. The objective of this research is to evaluate the influence of incorporating 1% by mass of nanofillers in laminated composites made with aramid fabric interspersed with nanoreinforced HDPE films. The laminated composites were assessed through bending tests, SHPB, and dynamic mechanical thermal analysis (DMTA). In addition to the samples containing NCC, MMT, and GNP, hybrid samples were prepared by intercalating films containing each nanofiller. The mechanical properties increased by 44%, 48%, and 55% in flexural strength and 46%, 69%, and 88% in flexural modulus for the composites prepared with calcium carbonate, graphene, and the hybrid graphene/calcium carbonate films, concerning the composite containing HDPE film. Moreover, the samples containing HDPE film with 1% GNP demonstrated a 79% increase in toughness, while the hybrid sample, which contained interspersed films of HDPE with 1% GNP and 1% NCC, exhibited a 46% increase in toughness. These results indicate a superior toughness response under high strain rates, contributing to enhanced energy dissipation. These two samples exhibited highly potential for ballistic industrial applications.Highlights: Laminated composites reinforced with NCC, MMT, and GNP nanofillers. Mechanical properties of laminated composites assessed using the Split‐Hopkinson pressure bar test and dynamic mechanical thermal analysis. Impact strength improvement through the incorporation of nanofiller into laminated composites. Enhanced energy dissipation in laminated composite materials.
- 24 February 2024
- Published by Springer Nature in Polymer Bulletin
- Vol. 81 (11) , 9893-9910
Mechanical, thermal, and dynamic compression of high-density polyethylene nanocomposites with graphene, montmorillonite, and calcium carbonate
- 24 February 2024
- Published by Springer Nature in Polymer Bulletin
- Vol. 81 (11) , 9893-9910
Mechanical, thermal, and dynamic compression of high-density polyethylene nanocomposites with graphene, montmorillonite, and calcium carbonate
- 14 February 2024
- Published by Wiley in Polymer Composites
- Vol. 45 (7) , 6720-6732
Acrylonitrile‐butadiene‐styrene‐based composites for the manufacture of anthropomorphic simulators
The development of functional compounds for extrusion applied in the additive manufacturing of anthropomorphic simulators is interesting, as it guarantees the manufacture of a 3D model similar to the patient. These simulators find applications in therapies or laboratory tests involving x‐rays. In order to replicate human conditions in these tests, it is essential to create materials that closely match the properties of human tissue, including the smoothness of soft tissues and the hardness of the bone tissue. This study developed ceramic‐polymeric composites, where the tomography intensity of each mixture was measured experimentally. Combinations of acrylonitrile butadiene styrene (ABS) with zirconium oxide and basic bismuth carbonate allowed imitation of bone tissue. The samples containing zirconium oxide and basic bismuth carbonate presented results that exceeded the minimum limit and reached a value close to 2000 Hounsfield units (HU) with 12% basic bismuth carbonate content. Combinations of ABS with hydroxyapatite and aluminum oxide can imitate soft tissues. The use of a surfactant facilitated the mixing of ceramic filler with polymer. Finally, 3D printing of a physical model was performed using a dual extruder printer, allowing simultaneous printing of bone and soft tissue components.Highlights: Material mimicking x‐ray attenuation similar to bone tissue. Relation between 3D printing porosity and intensity in Hounsfield unit. Computed tomography tests on a 3D printed anthropomorphic phantom. Creating a 3D model from a Computed Tomography scan. Double extruder for 3D printing of two tissue simultaneously.
- 14 February 2024
- Published by Wiley in Polymer Composites
- Vol. 45 (7) , 6720-6732
Acrylonitrile‐butadiene‐styrene‐based composites for the manufacture of anthropomorphic simulators
The development of functional compounds for extrusion applied in the additive manufacturing of anthropomorphic simulators is interesting, as it guarantees the manufacture of a 3D model similar to the patient. These simulators find applications in therapies or laboratory tests involving x‐rays. In order to replicate human conditions in these tests, it is essential to create materials that closely match the properties of human tissue, including the smoothness of soft tissues and the hardness of the bone tissue. This study developed ceramic‐polymeric composites, where the tomography intensity of each mixture was measured experimentally. Combinations of acrylonitrile butadiene styrene (ABS) with zirconium oxide and basic bismuth carbonate allowed imitation of bone tissue. The samples containing zirconium oxide and basic bismuth carbonate presented results that exceeded the minimum limit and reached a value close to 2000 Hounsfield units (HU) with 12% basic bismuth carbonate content. Combinations of ABS with hydroxyapatite and aluminum oxide can imitate soft tissues. The use of a surfactant facilitated the mixing of ceramic filler with polymer. Finally, 3D printing of a physical model was performed using a dual extruder printer, allowing simultaneous printing of bone and soft tissue components.Highlights: Material mimicking x‐ray attenuation similar to bone tissue. Relation between 3D printing porosity and intensity in Hounsfield unit. Computed tomography tests on a 3D printed anthropomorphic phantom. Creating a 3D model from a Computed Tomography scan. Double extruder for 3D printing of two tissue simultaneously.
- 7 September 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 128 (11-12) , 5289-5300
PLA-based ceramic composites for 3D printing of anthropomorphic simulators
- 7 September 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 128 (11-12) , 5289-5300
PLA-based ceramic composites for 3D printing of anthropomorphic simulators
- Open Access
- 1 January 2021
- Published by FapUNIFESP (SciELO) in Polímeros
- Vol. 31 (2)
PVC plasticizer from trimethylolpropane trioleate: synthesis, properties, and application
- 1 January 2021
- Published by FapUNIFESP (SciELO) in Polímeros
- Vol. 31 (2)
Open AccessPVC plasticizer from trimethylolpropane trioleate: synthesis, properties, and application