Mingxia Qiu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Mingxia Qiu has a total of 108 co-authors. Here are the top co-authors by number of shared publications:
- Shunpu Li
College of New Materials and New Energies, Shenzhen Technology University 1 , Shenzhen 518118
6 shared publications - Guangye Zhang
College of New Materials and New Energies, Shenzhen Technology University, Shenzhen, China
5 shared publications - Bobo Li
College of New Materials and New Energies Shenzhen Technology University Shenzhen People's Republic of China
4 shared publications - Chaoyue Zhao
College of New Materials and New Energies, Shenzhen Technology University, Shenzhen 518118, China
4 shared publications - Lihong Wang
College of New Materials and New Energies, Shenzhen Technology University, Shenzhen 518118, China
4 shared publications - Guoping Zhang
College of New Materials and New Energies, Shenzhen Technology University, Shenzhen 518118, China
3 shared publications
Latest Publications
- Open Access
Rational Design of Amino Acid-Modified Halide Perovskites for Highly Efficient and Cost-Effective Light-Emitting Diodes
Formamidinium lead bromide (FAPbBr3) quantum dots (QDs) have shown potential in light-emitting diodes (LEDs). However, their performance is constrained by surface defects and the limitations of charge transport. Zwitterionic ligands, owing to their twin functions of Lewis base coordination and electrostatic compensation, passivate surface defects of perovskite QDs. Some other zwitterionic ligands are high-cost, while amino acids, as zwitterionic ligands, are inexpensive, readily available, and have efficient passivation capabilities. Their short main chain and programmable side chain can control the volume and dipole at Å-scale range through functional group selection and feed ratio regulation, achieving interface energy level engineering. This work adopts green-emitting FAPbBr3 QDs as the model, tuning ligand properties by modifying side-chain functional groups, thereby achieving PLQY of 87.2%. Experimental results and DFT reveal that amino acids preferentially undergo coordination and can be further fine-tuned through conjugated contacts. Without severe site competition and without affecting coordination occupation and ligand uniformity, the EQE reaches 5.6% and the luminance exceeds 9000 cd/m2. This low-cost technology is easily scalable and broadly manufacturable, providing a replicable material and interface design route for green zone perovskite LEDs.
Open AccessRational Design of Amino Acid-Modified Halide Perovskites for Highly Efficient and Cost-Effective Light-Emitting Diodes
Formamidinium lead bromide (FAPbBr3) quantum dots (QDs) have shown potential in light-emitting diodes (LEDs). However, their performance is constrained by surface defects and the limitations of charge transport. Zwitterionic ligands, owing to their twin functions of Lewis base coordination and electrostatic compensation, passivate surface defects of perovskite QDs. Some other zwitterionic ligands are high-cost, while amino acids, as zwitterionic ligands, are inexpensive, readily available, and have efficient passivation capabilities. Their short main chain and programmable side chain can control the volume and dipole at Å-scale range through functional group selection and feed ratio regulation, achieving interface energy level engineering. This work adopts green-emitting FAPbBr3 QDs as the model, tuning ligand properties by modifying side-chain functional groups, thereby achieving PLQY of 87.2%. Experimental results and DFT reveal that amino acids preferentially undergo coordination and can be further fine-tuned through conjugated contacts. Without severe site competition and without affecting coordination occupation and ligand uniformity, the EQE reaches 5.6% and the luminance exceeds 9000 cd/m2. This low-cost technology is easily scalable and broadly manufacturable, providing a replicable material and interface design route for green zone perovskite LEDs.
- 26 July 2024
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 12 (35) , 13904-13914
Fine control of Ce doped CH3NH3PbBr3 to modulate photoluminescence and carrier characteristics for application in photoconductive photodetectors
Finely tunable amounts of Ce3+ ions into MAPbBr3 can improve the opto-electronic properties of photodetector.
- 26 July 2024
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 12 (35) , 13904-13914
Fine control of Ce doped CH3NH3PbBr3 to modulate photoluminescence and carrier characteristics for application in photoconductive photodetectors
Finely tunable amounts of Ce3+ ions into MAPbBr3 can improve the opto-electronic properties of photodetector.
- Open Access
- 16 May 2024
- Published by Frontiers Media SA in Frontiers in Materials
- Vol. 11, 1383816
Efficiency enhancement of non-fullerene organic solar cells using PEDOT:PSS diluted with alcohol solvents as the hole transport layer
The poly3,4-ethylenedioxythiophene) poly(styrene sulfonate) (PEDOT:PSS) hole transport layer (HTL) has always played a crucial role in achieving high-efficiency organic solar cells (OSCs) owing to its unique advantages of suitable energy levels and high optical transparency. However, the inherent insulation and easy aggregation property of PSS results in relatively low conductivity and high surface roughness of the PEDOT:PSS film, which is unfavorable for charge transport and the morphology of the top layer. To address these problems, we use PEDOT:PSS diluted in a series of alcoholic solvents and evaluate them on the PM6:Y6 system. Among these, the PM6:Y6 devices using PEDOT:PSS modified with ethanol as the HTL demonstrate the best vertical phase segregation and carrier extraction. In addition, the PEDOT:PSS film with added ethanol also has the smoothest surface compared to those diluted in the other alcoholic solvents. Finally, a high power conversion efficiency of 18.13% was obtained with the PM6:Y6 devices based on PEDOT:PSS modified by ethanol. This work provides a sufficient reference for the alcoholic modification of PEDOT:PSS and also proposes a feasible solution for high-efficiency OSCs.
- 16 May 2024
- Published by Frontiers Media SA in Frontiers in Materials
- Vol. 11, 1383816
Open AccessEfficiency enhancement of non-fullerene organic solar cells using PEDOT:PSS diluted with alcohol solvents as the hole transport layer
The poly3,4-ethylenedioxythiophene) poly(styrene sulfonate) (PEDOT:PSS) hole transport layer (HTL) has always played a crucial role in achieving high-efficiency organic solar cells (OSCs) owing to its unique advantages of suitable energy levels and high optical transparency. However, the inherent insulation and easy aggregation property of PSS results in relatively low conductivity and high surface roughness of the PEDOT:PSS film, which is unfavorable for charge transport and the morphology of the top layer. To address these problems, we use PEDOT:PSS diluted in a series of alcoholic solvents and evaluate them on the PM6:Y6 system. Among these, the PM6:Y6 devices using PEDOT:PSS modified with ethanol as the HTL demonstrate the best vertical phase segregation and carrier extraction. In addition, the PEDOT:PSS film with added ethanol also has the smoothest surface compared to those diluted in the other alcoholic solvents. Finally, a high power conversion efficiency of 18.13% was obtained with the PM6:Y6 devices based on PEDOT:PSS modified by ethanol. This work provides a sufficient reference for the alcoholic modification of PEDOT:PSS and also proposes a feasible solution for high-efficiency OSCs.
- 27 March 2024
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 6 (4) , 2168-2177
Floating-Gate-Coupled Two-Cell Electrochemical Transistor Augmented with Faradic Current Generated by Organic Semiconductor Ion Traps
- 27 March 2024
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 6 (4) , 2168-2177
Floating-Gate-Coupled Two-Cell Electrochemical Transistor Augmented with Faradic Current Generated by Organic Semiconductor Ion Traps
- 14 July 2023
- Published by IOP Publishing in Nanotechnology
- Vol. 34 (39) , 395202
Embedding TiO2 microspheres into the active layer as light scatterers in a perovskite photodetector to boost light harvesting
Here, TiO2 microspheres with particle sizes of 200–400 nm are embedded in p–i–n perovskite photodetectors, which are used as light scatterers. This approach was implemented to change the light transfer path in the perovskite layer, which gives the device higher photon-capture ability in a specific incident wavelength range. Compared with a pristine device, the photocurrent and responsivity of the device based on such a structure are obviously enhanced in the ranges of 560–610 nm and 730–790 nm. The photocurrent under 590 nm incident light wavelength illumination (light intensity P = 31.42 μW·cm−2) increases from 1.45 μA to 1.71 μA, with an increase of 17.93%, and the responsivity reaches 0.305 A·W−1. In addition, the introduction of TiO2 has no additional negative impact on the carrier extraction and the dark current. Also, the response time of the device did not deteriorate. Finally, the role of TiO2 as light scatterers is further verified by embedding microspheres into mixed-halide perovskite devices.
- 14 July 2023
- Published by IOP Publishing in Nanotechnology
- Vol. 34 (39) , 395202
Embedding TiO2 microspheres into the active layer as light scatterers in a perovskite photodetector to boost light harvesting
Here, TiO2 microspheres with particle sizes of 200–400 nm are embedded in p–i–n perovskite photodetectors, which are used as light scatterers. This approach was implemented to change the light transfer path in the perovskite layer, which gives the device higher photon-capture ability in a specific incident wavelength range. Compared with a pristine device, the photocurrent and responsivity of the device based on such a structure are obviously enhanced in the ranges of 560–610 nm and 730–790 nm. The photocurrent under 590 nm incident light wavelength illumination (light intensity P = 31.42 μW·cm−2) increases from 1.45 μA to 1.71 μA, with an increase of 17.93%, and the responsivity reaches 0.305 A·W−1. In addition, the introduction of TiO2 has no additional negative impact on the carrier extraction and the dark current. Also, the response time of the device did not deteriorate. Finally, the role of TiO2 as light scatterers is further verified by embedding microspheres into mixed-halide perovskite devices.
- 20 March 2023
- Published by IOP Publishing in Nanotechnology
- Vol. 34 (23) , 235706
Defect recombination suppression and carrier extraction improvement for efficient CsPbBr3/SnO2 heterojunction photodetectors
Perovskite materials with excellent optical and electronic properties have huge potential in the research field of photodetectors. Constructing heterojunctions and promoting carrier transportation are significant for the development of perovskite-based optoelectronics devices with high performances. Herein, we demonstrated a CsPbBr3/SnO2 heterojunction photodetector and improved the device performances through post-annealing treatment of SnO2 film. The results indicated that the electrical properties of SnO2 films will make an important impact on carrier extraction, especially for type-II heterojunction. As the electrons transfer layer in CsPbBr3/SnO2 type-II heterojunction, defects related to oxygen vacancy should be the key factor to affect carrier concentration, induce carriers’ limitation and recombination rate. Under proper annealing temperature for SnO2 layer, the recombination rate can decrease to 1.37 × 1021 cm3 s and the spectral responsivity will be highly increased. This work can enhance the understanding on the photoresponse of perovskite photodetectors, and will be helpful for the further optimization and design of optoelectronic devices based on the perovskite heterojunction.
- 20 March 2023
- Published by IOP Publishing in Nanotechnology
- Vol. 34 (23) , 235706
Defect recombination suppression and carrier extraction improvement for efficient CsPbBr3/SnO2 heterojunction photodetectors
Perovskite materials with excellent optical and electronic properties have huge potential in the research field of photodetectors. Constructing heterojunctions and promoting carrier transportation are significant for the development of perovskite-based optoelectronics devices with high performances. Herein, we demonstrated a CsPbBr3/SnO2 heterojunction photodetector and improved the device performances through post-annealing treatment of SnO2 film. The results indicated that the electrical properties of SnO2 films will make an important impact on carrier extraction, especially for type-II heterojunction. As the electrons transfer layer in CsPbBr3/SnO2 type-II heterojunction, defects related to oxygen vacancy should be the key factor to affect carrier concentration, induce carriers’ limitation and recombination rate. Under proper annealing temperature for SnO2 layer, the recombination rate can decrease to 1.37 × 1021 cm3 s and the spectral responsivity will be highly increased. This work can enhance the understanding on the photoresponse of perovskite photodetectors, and will be helpful for the further optimization and design of optoelectronic devices based on the perovskite heterojunction.
- Open Access
MDACl2-Modified SnO2 Film for Efficient Planar Perovskite Solar Cells
The electron transport layer (ETL) with excellent charge extraction and transport ability is one of the key components of high-performance perovskite solar cells (PSCs). SnO2 has been considered as a more promising ETL for the future commercialization of PSCs due to its excellent photoelectric properties and easy processing. Herein, we propose a facile and effective ETL modification strategy based on the incorporation of methylenediammonium dichloride (MDACl2) into the SnO2 precursor colloidal solution. The effects of MDACl2 incorporation on charge transport, defect passivation, perovskite crystallization, and PSC performance are systematically investigated. First, the surface defects of the SnO2 film are effectively passivated, resulting in the increased conductivity of the SnO2 film, which is conducive to electron extraction and transport. Second, the MDACl2 modification contributes to the formation of high-quality perovskite films with improved crystallinity and reduced defect density. Furthermore, a more suitable energy level alignment is achieved at the ETL/perovskite interface, which facilitates the charge transport due to the lower energy barrier. Consequently, the MDACl2-modified PSCs exhibit a champion efficiency of 22.30% compared with 19.62% of the control device, and the device stability is also significantly improved.
Open AccessMDACl2-Modified SnO2 Film for Efficient Planar Perovskite Solar Cells
The electron transport layer (ETL) with excellent charge extraction and transport ability is one of the key components of high-performance perovskite solar cells (PSCs). SnO2 has been considered as a more promising ETL for the future commercialization of PSCs due to its excellent photoelectric properties and easy processing. Herein, we propose a facile and effective ETL modification strategy based on the incorporation of methylenediammonium dichloride (MDACl2) into the SnO2 precursor colloidal solution. The effects of MDACl2 incorporation on charge transport, defect passivation, perovskite crystallization, and PSC performance are systematically investigated. First, the surface defects of the SnO2 film are effectively passivated, resulting in the increased conductivity of the SnO2 film, which is conducive to electron extraction and transport. Second, the MDACl2 modification contributes to the formation of high-quality perovskite films with improved crystallinity and reduced defect density. Furthermore, a more suitable energy level alignment is achieved at the ETL/perovskite interface, which facilitates the charge transport due to the lower energy barrier. Consequently, the MDACl2-modified PSCs exhibit a champion efficiency of 22.30% compared with 19.62% of the control device, and the device stability is also significantly improved.
- Open Access
- 21 December 2022
- Published by MDPI AG in Micromachines
- Vol. 14 (1) , 11
Performance Enhancement of Perovskite Quantum Dot Light-Emitting Diodes via Management of Hole Injection
Poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) is widely used in optoelectronic devices due to its excellent hole current conductivity and suitable work function. However, imbalanced carrier injection in the PEDOT:PSS layer impedes obtaining high-performance perovskite light-emitting diodes (PeLEDs). In this work, a novel poly[(9,9-dioctylfluorenyl-2,7-diyl)-co-(4,40-(N-(p-butylphenyl))diphenylamine)] (TFB) is applied as the hole transport layers (HTLs) to facilitate the hole injection with cascade-like energy alignment between PEDOT:PSS and methylammonium lead tribromide (MAPbBr3) film. Our results indicate that the introduced TFB layer did not affect the surface morphology or lead to any additional surface defects of the perovskite film. Consequently, the optimal PeLEDs with TFB HTLs show a maximum current efficiency and external quantum efficiency (EQE) of 21.26 cd A−1 and 6.68%, respectively. Such EQE is 2.5 times higher than that of the control devices without TFB layers. This work provides a facile and robust route to optimize the device structure and improve the performance of PeLEDs.
- 21 December 2022
- Published by MDPI AG in Micromachines
- Vol. 14 (1) , 11
Open AccessPerformance Enhancement of Perovskite Quantum Dot Light-Emitting Diodes via Management of Hole Injection
Poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) is widely used in optoelectronic devices due to its excellent hole current conductivity and suitable work function. However, imbalanced carrier injection in the PEDOT:PSS layer impedes obtaining high-performance perovskite light-emitting diodes (PeLEDs). In this work, a novel poly[(9,9-dioctylfluorenyl-2,7-diyl)-co-(4,40-(N-(p-butylphenyl))diphenylamine)] (TFB) is applied as the hole transport layers (HTLs) to facilitate the hole injection with cascade-like energy alignment between PEDOT:PSS and methylammonium lead tribromide (MAPbBr3) film. Our results indicate that the introduced TFB layer did not affect the surface morphology or lead to any additional surface defects of the perovskite film. Consequently, the optimal PeLEDs with TFB HTLs show a maximum current efficiency and external quantum efficiency (EQE) of 21.26 cd A−1 and 6.68%, respectively. Such EQE is 2.5 times higher than that of the control devices without TFB layers. This work provides a facile and robust route to optimize the device structure and improve the performance of PeLEDs.
- Open Access
Revealing the Hidden Mechanism of Enhanced Responsivity of Doped p-i-n Perovskite Photodiodes via Coupled Opto-Electronic Model
Organic-inorganic halide perovskites have demonstrated preeminent optoelectronic performance in recent years due to their unique material properties, and have shown great potential in the field of photodetectors. In this study, a coupled opto-electronic model is constructed to reveal the hidden mechanism of enhancing the performance of perovskite photodetectors that are suitable for both inverted and regular structure doped p-i-n perovskite photodiodes. Upon illumination, the generation rate of photogenerated carriers is calculated followed by carrier density distribution, which serves as a coupled joint to further analyze the recombination rate, electric field strength, and current density of carriers under different doping types and densities. Moreover, experiments were carried out in which the doping types and densities of the active layer were regulated by changing the precursor ratios. With optimal doping conditions, the inverted and regular perovskite photodiodes achieved an external quantum efficiency of 74.83% and 73.36%, and a responsivity of 0.417 and 0.404 A/W, respectively. The constructed coupled opto-electronic model reveals the hidden mechanism and along with the doping strategy, this study provides important guidance for further analysis and improvement of perovskite-based photodiodes.
Open AccessRevealing the Hidden Mechanism of Enhanced Responsivity of Doped p-i-n Perovskite Photodiodes via Coupled Opto-Electronic Model
Organic-inorganic halide perovskites have demonstrated preeminent optoelectronic performance in recent years due to their unique material properties, and have shown great potential in the field of photodetectors. In this study, a coupled opto-electronic model is constructed to reveal the hidden mechanism of enhancing the performance of perovskite photodetectors that are suitable for both inverted and regular structure doped p-i-n perovskite photodiodes. Upon illumination, the generation rate of photogenerated carriers is calculated followed by carrier density distribution, which serves as a coupled joint to further analyze the recombination rate, electric field strength, and current density of carriers under different doping types and densities. Moreover, experiments were carried out in which the doping types and densities of the active layer were regulated by changing the precursor ratios. With optimal doping conditions, the inverted and regular perovskite photodiodes achieved an external quantum efficiency of 74.83% and 73.36%, and a responsivity of 0.417 and 0.404 A/W, respectively. The constructed coupled opto-electronic model reveals the hidden mechanism and along with the doping strategy, this study provides important guidance for further analysis and improvement of perovskite-based photodiodes.
- Open Access
Efficient All-Polymer Solar Cells Enabled by Interface Engineering
All-polymer solar cells (all-PSCs) are organic solar cells in which both the electron donor and the acceptor are polymers and are considered more promising in large-scale production. Thanks to the polymerizing small molecule acceptor strategy, the power conversion efficiency of all-PSCs has ushered in a leap in recent years. However, due to the electrical properties of polymerized small-molecule acceptors (PSMAs), the FF of the devices is generally not high. The typical electron transport material widely used in these devices is PNDIT-F3N, and it is a common strategy to improve the device fill factor (FF) through interface engineering. This work improves the efficiency of all-polymer solar cells through interfacial layer engineering. Using PDINN as the electron transport layer, we boost the FF of the devices from 69.21% to 72.05% and the power conversion efficiency (PCE) from 15.47% to 16.41%. This is the highest efficiency for a PY-IT-based binary all-polymer solar cell. This improvement is demonstrated in different all-polymer material systems.
Open AccessEfficient All-Polymer Solar Cells Enabled by Interface Engineering
All-polymer solar cells (all-PSCs) are organic solar cells in which both the electron donor and the acceptor are polymers and are considered more promising in large-scale production. Thanks to the polymerizing small molecule acceptor strategy, the power conversion efficiency of all-PSCs has ushered in a leap in recent years. However, due to the electrical properties of polymerized small-molecule acceptors (PSMAs), the FF of the devices is generally not high. The typical electron transport material widely used in these devices is PNDIT-F3N, and it is a common strategy to improve the device fill factor (FF) through interface engineering. This work improves the efficiency of all-polymer solar cells through interfacial layer engineering. Using PDINN as the electron transport layer, we boost the FF of the devices from 69.21% to 72.05% and the power conversion efficiency (PCE) from 15.47% to 16.41%. This is the highest efficiency for a PY-IT-based binary all-polymer solar cell. This improvement is demonstrated in different all-polymer material systems.