Vasilica Popescu

Prunus spinosa fruit extract was investigated as a plant-derived coloring system for protein-based textiles by evaluating the effects of substrate, mordanting, dyeing conditions, and dye-bath pH. Knitted wool, woven wool, and silk were dyed without mordant or with alum or black tea biomordant and evaluated by K/S, CIELAB parameters, apparent dye-bath exhaustion, residual-bath reuse, and color fastness. Dyeing performance varied with substrate and processing conditions, with knitted wool consistently exhibiting the highest color strength. At 100 °C, extending dyeing from 1 to 3 h increased K/S from 4.52 to 8.55 without mordant, 4.67 to 7.24 with alum, and 5.59 to 11.13 with black tea. Black tea produced marked color differences for knitted wool (ΔE* = 5.121) and silk (ΔE* = 4.707), but only a minor change for woven wool (ΔE* = 0.306). Adjustment of the dye baths from their initial pH to pH 3.5 did not consistently improve color strength. Apparent exhaustion did not consistently parallel color strength, while cumulative exhaustion indicated progressive dye-bath depletion and measurable coloration persisted through the initial dyeing and four successive residual-bath reuse cycles. Black tea showed potential as a biomordant, yielding higher overall color strength and high fastness in knitted wool.

Sustainable textile care formulations based on renewable and waste vegetable oils represent environmentally responsible alternatives to conventional laundry products while supporting circular bioeconomy strategies. However, the influence of formulation composition on EO transfer, textile persistence and multifunctional performance remains poorly understood. This study investigated the influence of formulation design on the physicochemical properties, encapsulation efficiency, EO transfer, textile persistence, washing performance and antibacterial activity of sustainable textile care formulations prepared from virgin and waste vegetable oils. All formulations exhibited appropriate physicochemical characteristics, including alkaline pH values (9.84–10.64), good foaming capacity and encapsulation efficiencies of 95.6–98.2%. Although encapsulation efficiency remained consistently high, formulation composition influenced EO transfer and persistence on textile substrates. Formulation V1-D exhibited the most balanced overall performance. Waste vegetable oil formulations achieved washing efficiencies of 86–92%, comparable to those of virgin oil formulations, while maintaining EO persistence on textile substrates. The developed soap formulations also exhibited pronounced antibacterial activity against Staphylococcus aureus and Escherichia coli. These findings indicate that rational formulation design, rather than encapsulation efficiency alone, primarily determines the overall performance of sustainable multifunctional textile care formulations by balancing washing efficiency, EO transfer, textile persistence, and the antibacterial activity of the developed soap formulations.

Hemp plants are precious resources for the textile industry, being considered a sustainable and more economical alternative to cotton. Sustainable dyeing processes should minimize the consumption of water, energy, and chemicals while ensuring high color intensity and reducing the pollution load of residual baths. Black carrot (Daucus carota L. ssp. sativus) is a valuable source of dyes for dyeing hemp materials because it is rich in anthocyanins and anthocyanidins, which generate colors ranging from red-orange and muted magenta to blue, depending on the pH. In this article, the dye extraction process was colorimetrically monitored for 26 days to determine the optimal fermentation/storage period that generates the most intense color during the dyeing process. The dyeing parameters tested were temperature (40–100 °C), pH (4.33–9.15), duration (1–24 h), concentration (2.5–10%), and the presence of organic acids (ascorbic and citric acids). Virgin baths and the first three residual baths were used in the dyeing process. While the results of FTIR, SEM, and EDX analyses confirmed the dyeing process, the CIEL*a*b* measurements quantified the characteristics of the colors obtained using virgin and residual baths. The 12 principles of green chemistry were also discussed, together with their implementation in hemp dyeing.

This study investigates the influence of conventional textile pretreatment and periodate oxidation parameters on the structural modifications and functional properties of woven cotton fabrics. Unlike most studies focused on cellulose pulps or isolated textile fibers, the present work examines how the initial structural state of the textile substrate, determined by its pretreatment history, governs the oxidation pathways. Cotton fabrics were subjected to alkaline scouring (SC), hydrogen peroxide bleaching (BC), and combined scouring–bleaching (SBC), followed by sodium periodate oxidation under controlled conditions. Carbonyl species were quantified analytically and identified by ATR-FTIR spectroscopy, while structural changes were evaluated by X-ray diffraction (XRD). Mechanical properties were assessed using the normalized parameters (Fa/Fa₀ and E/E₀), hydrophilicity by water absorption capacity (WAC), and optical stability by the yellowness index (YI). The results demonstrated that the pretreatments influence the oxidant accessibility and the balance between carbonyl speciation. XRD analysis shows a moderate decrease in crystallinity, indicating partial preservation of the crystalline domains, whereas mechanical properties decrease significantly (35–65%), concomitant with a 25–45% reduction in WAC. These results suggest that the impairment in mechanical and hydrophilic properties is primarily governed by localized C2–C3 bond scission, secondary oxidative reactions, and supramolecular rearrangements, rather than by bulk crystalline loss. The oxidized SC series exhibits higher YI values associated with an increased free aldehyde content, while the BC and SBC fabrics show improved optical stability. Overall, these results demonstrate that pretreatment history governs periodate oxidation pathways and establishes clear structure–property relationship relevant for the controlled functionalization of woven cotton fabrics.

Classical and modern methods are used to release curcumin by degrading the polysaccharides found in the turmeric powder matrix. Classical methods use chemicals as acids (HCl, H₂SO₄, CH₃COOH), oxidants (H₂O₂, kojic acid), and enzymes (amylase type) that can degrade amylose and amylopectin from starch. The modern applied methods consist of the degradation of the polysaccharides in the turmeric powder during eco-friendly processes assisted by ultrasound or microwaves. The extraction medium can consist of only water, water with a solvent, and/or an oxidizing agent. The presence of curcumin in turmeric powder is confirmed by FTIR analysis. The UV–VIS analysis of the extracts allows the determination of the efficiency of modern extraction processes. The release of curcumin from turmeric is highlighted quantitatively by colorimetric measurements for the obtained extracts, using a portable DataColor spectrophotometer. The comparison of the results leads to the conclusion that microwave-assisted extractions are the most effective. These extracts are able to dye many types of textile fibers: wool, cotton, hemp, silk, polyacrylonitrile, polyamide, polyester, and cellulose acetate. CIELab and color strength (K/S) measurements indicate that the most intense yellow colors are obtained on polyacrylonitrile (b* = 86.32, K/S = 15.14) and on cellulose acetate (b* = 90.40, K/S = 14.17).

This article demonstrates that the quality of laundry soap obtained by hot/cold saponification of two vegetable oils (olive and coconut) and an essential oil (such as Neem, Tea Tree or Thyme) influences the effects obtained after washing textiles: cleansing capacity and antibacterial effect. The results of FTIR, SEM, EDX, thermogravimetry and colorimetry analyses are presented comparatively for hot- and cold-prepared soaps. Saponification, Iodine number and Iodine Number Saponification values are determined for each oil but also for the mixture used in soap-making. Soap quality refers to texture, hardness, foaming capacity, stability, durability, cleansing capacity after washing and antimicrobial capacity. The removal power of greasy dirt (heavy used engine oil) of these laundry soaps is higher than that of some commercial soaps, obtaining dirt visibility <2.6% after washing at 100 °C, soiling addition density SAD < 0.0229 and cleansing capacity between 80.88 and 92.16%. UV-VIS analysis confirms the presence of essential oil in soaps (even after 10 months from manufacture) but also in textiles washed with them. The essential oil imparts strong antimicrobial properties to the laundry soaps (since they do not allow for attachment or multiplication of microorganisms from the environment), which makes them particularly useful in washing and disinfecting textile products used in hospitals.

Beta vulgaris L. is a biennial plant easily accessible all over the world, rich in various biologically active compounds, especially a class of extremely bioactive pigments known as betalains. These dyes predominate in the pulp and peels of beetroot, which is why they can be valorized in food, medicine or in the textile industry. In this work, betalains extractions were carried out applying 3 sustainable options: (1) dissolving/solubilizing betalains in water; (2) extraction under pressure; (3) extraction assisted by an enzyme/pectinase. The obtained extracts were analyzed in the UV-Vis domain, which allowed their characterization by determining the total monomeric anthocyanins, color density (control), polymeric density and browning index. The HPLC-MS analysis highlighted the extracts composition. The colors characteristics were determined through CIELab measurements. The performances of these 3 extracts, during green dyeing (without mordants), were evaluated according to the color characteristics (L*, a*, b* and K/S) of the dyed wool samples under different conditions: pH, temperature, duration of dyeing and volume of extract and stabilizers (Vitamin E and EDTA). Betalains can be considered acid dyes, with a low affinity for wool, which in a pronounced acidic environment dye the wool in an intense, uniform way and with good resistance to washing and rubbing.

The development of intelligent materials for protective equipment applications is still growing, with enormous potential to improve the safety of personnel functioning in specialized professions, such as firefighters. The design and production of such materials by the chemical modification of biodegradable semisynthetic polymers, accompanied by modern manufacturing techniques such as electrospinning, which may increase specific properties of the targeted material, continue to attract the interest of researchers. Phosphorus-modified poly(vinyl alcohol)s have been, thus, synthesized and utilized to prepare environmentally friendly electrospun mats. Poly(vinyl alcohol)s of three different molecular weights and degrees of hydrolysis were phosphorylated by polycondensation reaction in solution in the presence of phenyl dichlorophosphate in order to enhance their flame resistance and thermal stability. The thermal behavior and the flame resistance of the resulting phosphorus-modified poly(vinyl alcohol) products were investigated by thermogravimetric analysis and by cone calorimetry at a micro scale. Based on the as-synthesized phosphorus-modified poly(vinyl alcohol)s, electrospun mats were successfully fabricated by the electrospinning process. Rheology studies were performed to establish the optimal conditions of the electrospinning process, and scanning electron microscopy investigations were undertaken to observe the morphology of the phosphorus-modified poly(vinyl alcohol) electrospun mats.

The beetroot peels can be a sustainable source of betalains that can dye the wool materials through green processes based on low water and energy consumption. Green chemistry in the extraction of betalains from colored food waste/peels from red beetroot involved the use of water as a solvent, without other additives. In order for the extract obtained to be able to dye the wool, it was necessary to functionalize betalains or even the wool. Three types of sustainable functionalizations were performed, with (1) acetic acid; (2) ethanol; and (3) arginine. For each functionalization, the mechanism that can justify dyeing the wool in intense colors was elucidated. The characterization of the extract was performed with the data provided by UV-VIS and HPLC-MS analyses. The characterization of the wool dyed with the extract obtained from the red beetroot peels was possible due to the information resulting from the FTIR and CIELab analyses. The functionalizations of betalains and wool in acid environments lead to the most intense red colors. The color varies depending on the pH and the concentration of betalains.

This study may open a new way to obtain the coloration of a polymer during functionalization. Two polyacrylonitrile (PAN) polymers in the form of textile fibers (Melana and Dralon L) were subjected to functionalization treatments in order to improve the dyeing capacity. The functionalizations determined by an organo-hypervalent iodine reagent developed in situ led to fiber coloration without using dyes. KIO₃ was formed in situ from the interaction of aqueous solutions of 3–9% KOH with 3–9% I₂, at 120 °C. The yellow-orange coloration appeared as a result of the transformations in the chemical structure of each functionalized polymer, with the formation of iodinehydrin groups. The degree of functionalization directly influenced the obtained color. The results of the Fourier Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscopy (SEM), Energy Dispersive X-ray Spectroscopy (EDX), Map and Temogravimetric Analysis (TG) plus Differential Thermal (DTA) analyses indicated the presence of new functional groups, such as iodine-oxime. The X-ray diffraction (XRD) analysis confirmed the change of the crystalline/amorphous ratio in favor of the former. The new groups introduced by functionalization make it possible to dye with classes of dyes specific to these groups, but not specific to PAN fibers, thus improving their dyeing capacity.