Max M. Garvue
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Max M. Garvue has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- James A. Spotila
Department of Geosciences Virginia Tech Blacksburg VA USA
2 shared publications - Elizabeth R. Curtiss
Department of Geosciences, Virginia Tech, 926 West Campus Drive, Blacksburg, Virginia 24061, USA
1 shared publication - Michele Lynn Cooke
Department of Earth, Geographic and Climate Sciences, University of Massachusetts Amherst, Amherst, 01003, USA
1 shared publication
Latest Publications
- Open Access
- 31 May 2024
- Published by American Geophysical Union (AGU) in Tectonics
- Vol. 43 (6)
What Controls Early Restraining Bend Growth? Structural, Morphometric, and Numerical Modeling Analyses From the Eastern California Shear Zone
Restraining bends influence topography, strike‐slip evolution, and earthquake rupture dynamics, however the specific factors governing their geometry and development in the crust are not well established. These relationships are challenging to investigate in field examples due to cannibalization and erosion of earlier structures with cumulative strain. To address this knowledge gap, we investigated the structure, morphology, and kinematics of 22 basement‐cored restraining bends on low net‐slip faults (<10 km) within the southern Eastern California shear zone (SECSZ) via mapping, topographic analyses, and 3D numerical modeling. The bends are self‐similar in form with most exhibiting focused relief between high‐angle bounding faults with an arrowhead shape in map view and a “whaleback” longitudinal profile. Slight changes in that form occur with increasing size indicating predictable growth that appears to be primarily controlled by local fault geometries (i.e., bifurcation angle), rather than the influence of fault obliquity relative to far‐field plate motion, due to inefficient slip‐transfer across interconnected irregularly trending closely spaced faults. Modeling results indicate that the self‐similar fault‐bound geometry of SECSZ restraining bends may arise from elevated shear strain at the outer corners of single transpressional fault bends with increasing cumulative slip. This, in turn, promotes growth of a new fault leading to efficient accommodation of local convergent strain via uplift between bounding faults. Finally, our results indicate that the kilometer‐scale restraining bends contribute minimally to regional contraction as they only penetrate the upper third of the seismogenic crust and are therefore also unlikely to impede large earthquake surface ruptures.
- 31 May 2024
- Published by American Geophysical Union (AGU) in Tectonics
- Vol. 43 (6)
Open AccessWhat Controls Early Restraining Bend Growth? Structural, Morphometric, and Numerical Modeling Analyses From the Eastern California Shear Zone
Restraining bends influence topography, strike‐slip evolution, and earthquake rupture dynamics, however the specific factors governing their geometry and development in the crust are not well established. These relationships are challenging to investigate in field examples due to cannibalization and erosion of earlier structures with cumulative strain. To address this knowledge gap, we investigated the structure, morphology, and kinematics of 22 basement‐cored restraining bends on low net‐slip faults (<10 km) within the southern Eastern California shear zone (SECSZ) via mapping, topographic analyses, and 3D numerical modeling. The bends are self‐similar in form with most exhibiting focused relief between high‐angle bounding faults with an arrowhead shape in map view and a “whaleback” longitudinal profile. Slight changes in that form occur with increasing size indicating predictable growth that appears to be primarily controlled by local fault geometries (i.e., bifurcation angle), rather than the influence of fault obliquity relative to far‐field plate motion, due to inefficient slip‐transfer across interconnected irregularly trending closely spaced faults. Modeling results indicate that the self‐similar fault‐bound geometry of SECSZ restraining bends may arise from elevated shear strain at the outer corners of single transpressional fault bends with increasing cumulative slip. This, in turn, promotes growth of a new fault leading to efficient accommodation of local convergent strain via uplift between bounding faults. Finally, our results indicate that the kilometer‐scale restraining bends contribute minimally to regional contraction as they only penetrate the upper third of the seismogenic crust and are therefore also unlikely to impede large earthquake surface ruptures.
- Open Access
- 2 November 2021
- Published by American Geophysical Union (AGU) in Tectonics
- Vol. 40 (11)
Kinematics and Evolution of the Southern Eastern California Shear Zone, Based on Analysis of Fault Strike, Distribution, Activity, Roughness, and Secondary Deformation
The Eastern California shear zone is a complex set of dextral faults that accommodates significant plate motion and has produced large earthquakes. The evolution of this system and why it consists of closely spaced, irregular faults that fail in multi‐fault ruptures are not well understood. Here we analyze the geometry, spatial distribution, and Quaternary slip activity of right‐lateral faults in the southern Mojave block. We find these faults are oriented favorably for accommodating regional dextral plate motion and do not show evidence of replacement following counterclockwise rotation to unfavorable positions, although activity may be migrating westward as previously proposed. We also confirm that the shear zone is transpressive, with widespread restraining bends, distributed convergent deformation, and significant impact on near‐fault topography. Observations also show that faults are geometrically complex, as represented by along‐strike variability in fault strike. We document a correlation between strike variability and fault activity (slip rate or net slip), which is evident within the shear zone as well as for a control group of other faults. We suggest that strike variability represents a form of geometric roughness, which may inhibit fault slip and result in complex ruptures, slip‐strengthening behavior, and a prevalence of off‐fault deformation. Other factors, including preexisting crustal fabric, edge effects, and changes in the stress field, may further complicate kinematics. These results suggest that faults of the shear zone are still juvenile and somewhat unique, yet offer an important window into how broadly distributed shear may evolve into a through‐going continental transform system.
- 2 November 2021
- Published by American Geophysical Union (AGU) in Tectonics
- Vol. 40 (11)
Open AccessKinematics and Evolution of the Southern Eastern California Shear Zone, Based on Analysis of Fault Strike, Distribution, Activity, Roughness, and Secondary Deformation
The Eastern California shear zone is a complex set of dextral faults that accommodates significant plate motion and has produced large earthquakes. The evolution of this system and why it consists of closely spaced, irregular faults that fail in multi‐fault ruptures are not well understood. Here we analyze the geometry, spatial distribution, and Quaternary slip activity of right‐lateral faults in the southern Mojave block. We find these faults are oriented favorably for accommodating regional dextral plate motion and do not show evidence of replacement following counterclockwise rotation to unfavorable positions, although activity may be migrating westward as previously proposed. We also confirm that the shear zone is transpressive, with widespread restraining bends, distributed convergent deformation, and significant impact on near‐fault topography. Observations also show that faults are geometrically complex, as represented by along‐strike variability in fault strike. We document a correlation between strike variability and fault activity (slip rate or net slip), which is evident within the shear zone as well as for a control group of other faults. We suggest that strike variability represents a form of geometric roughness, which may inhibit fault slip and result in complex ruptures, slip‐strengthening behavior, and a prevalence of off‐fault deformation. Other factors, including preexisting crustal fabric, edge effects, and changes in the stress field, may further complicate kinematics. These results suggest that faults of the shear zone are still juvenile and somewhat unique, yet offer an important window into how broadly distributed shear may evolve into a through‐going continental transform system.