JŽJaroslav Žák

Jaroslav Žák

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jaroslav Žák has a total of 5 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Assessment of Soil Resilient Modulus Under Cyclic Loading Using Cyclic CBR Test Equipment

    by Lenka Ševelová, Aleš Florian, Jaroslav Žák

    Soil materials and road pavement construction materials are subjected to dynamic and repetitive loading of different intensity from vehicle traffic. To account for the cyclic nature of material loading and its non-linear behavior, the concept of the resilient modulus has been adopted. It is a fundamental property of unbound pavement materials, as it quantifies the stiffness of the material under repeated loading. Its real value depends on the actual material parameters—e.g., maximum dry density, moisture content, compaction method, and the number and magnitude of repeated loads—and on the state of stress of the actual pavement structure. The resilient modulus value is therefore not constant for a given material type but varies over a certain interval depending on the above-mentioned parameters and the actual test conditions. Therefore, the method of determining the resilient modulus must take into account all the above factors. The standard method for resilient modulus determination is the cyclic triaxial test, but the cyclic CBR test procedure is also used. It uses standard California Bearing Ratio (CBR) test equipment, and thus it is a very simple and very economical testing method. In the presented paper, the influence of loading force and number of loading cycles on the deformation characteristic and resilient modulus of the analyzed soil is investigated. A total of 72 soil specimens are tested at two different levels of loading force and six different numbers of loading cycles. The obtained results confirm that the resilience modulus increases with increasing loading force value and with increasing number of loading cycles. For the soil analyzed, the resilient modulus ranges in the interval 31-83 MPa.

  • Open Access

    An Updated Cyclic CBR Test with Realistic Stress Values under the Plunger for Resilient Modulus Calculation

    by Aleš Florian, Lenka Ševelová, Kateřina Žáková, Jaroslav Žák

    The design and assessment of forest and rural road pavements made from unbound natural and recycled materials require the careful determination of their physical-mechanical properties. The fundamental parameter for characterizing the soil material property is considered to be the resilient modulus Mr. The generally accepted alternative solution for its calculation is the cyclic CBR test, which uses standard CBR testing equipment. To perform tests on intact specimens and under stress conditions corresponding to expected states of stress in a pavement structure, an updated cyclic CBR test is proposed. In contrast to the standard cyclic CBR test, the applied loading force for repeated loadings is not determined in the first loading step by the plunger penetration to the prescribed depth, but by the stress value that is expected in an actual pavement structure. The updated test was verified on 240 tested specimens taken from a total of 40 soil samples belonging to nine soil types according to the USCS system. The resilient modulus results obtained are compared with those obtained using the standard cyclic CBR test and the cyclic triaxial test.


  • Open Access

    Influence of Plunger Stress on Resilient Modulus of Forest Subgrade Soils Obtained from Cyclic CBR Test

    by Lenka Ševelová, Aleš Florian, Jaroslav Žák

    The low load-bearing capacity of subgrade soils is typical for forest roads. For the determination of the resilient modulus Mr of unbound natural as well as recycled materials, a laboratory triaxial test with cyclic loading is generally preferred. For low volume roads, including forest roads, an alternative method of the cyclic CBR test, which uses standard CBR devices for repeated loading, is being tested and applied in practice. For forest subgrade soils, the procedure for determining the modulus Mr based on cyclic loading of the specimen to a constant penetration depth of 2.54 mm was verified. This procedure was tested on an extensive dataset obtained from 11 forest roads in the Czech Republic, which was then statistically evaluated. The obtained results showed disproportionately high mean values as well as high random variability. Further data analysis revealed that the reason seemed to be the chosen test methodology. When using this procedure for forest soils, high values of plunger stress can occur, which for many types of soils greatly exceed their maximum load-bearing capacity. As result, the modulus Mr is determined at unrealistically high plunger stress values and in many cases on the disrupted specimen. The necessary solution to this shortcoming is to censor the results of the cyclic CBR test, i.e., to exclude unrealistic values of the modulus Mr determined at plunger stresses exceeding the limit values.


  • Open Access

    Reliability Analysis of Temperature Influence on Stresses in Rigid Pavement Made from Recycled Materials

    by Aleš Florian, Lenka Ševelová, Jaroslav Žák

    Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, the scientific journal of the Mendel University in Brno, Czech Republic


  • Open Access

    Data Envelopment Analysis for Technological, Environmental and Economic Analysis of Motorway Underpasses

    by KateřIna Myšková, Jaroslav Žák

    Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, the scientific journal of the Mendel University in Brno, Czech Republic


  • Open Access

    Influence of Environmental Humidity on Mechanical Properties of Natural and Recycled Unbound Materials

    by Aleš Florian, Lenka Ševelová, Jaroslav Žák

    Low volume roads are widely used all over the world. To improve their quality a FEM computer simulation of their behavior is proposed. The input information about mechanical properties of individual materials is crucial for obtaining results as exact as possible. Among others, the mechanical properties are generally dependent on the state of stress and on humidity conditions. For this purpose the cyclic-load triaxial machine testing of cyclic-load performance of materials seems to be a promising test method. The test specimens can be prepared with different amounts of water. Thus modulus of elasticity (Young modulus) of different materials including recycled ones can be measured under the different conditions of horizontal and vertical stresses and under the different humidity conditions. Using the proposed testing procedure the modulus of elasticity of materials used in the newly built low volume road is obtained under the different state of stress as well as humidity conditions set to standard, dry and fully saturated level. Also recycled materials which are able to replace the traditional materials in the pavement are tested. Obtained values of modulus of elasticity can be used in a FEM study of the newly built road.