SHSaeed Habibi

Saeed Habibi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Saeed Habibi has a total of 4 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • An Impedance-Source-Based Soft-Switched High Step-Up DC–DC Converter With an Active Clamp

    by Saeed Habibi, Ramin Rahimi, Mehdi Ferdowsi, Pourya Shamsi

    This article proposes a high step-up dc–dc converter based on a trans-inverse impedance-source structure, in which the voltage gain of the converter is increased by using a lower number of turns ratio of the coupled inductors (CI) windings. The proposed converter achieves a very high voltage gain and a very low voltage stress on the switches. An active clamp is incorporated into the topology of the proposed converter, helping to absorb the energy of the leakage inductances of the CI, and to recycle that energy to the output of the converter to further increase the voltage gain. Furthermore, the active clamp is used to realize soft turn on for the main switch of the converter. Additionally, the clamp switch also turns on under zero voltage switching condition. Apart from the soft turn on of the switches of the proposed converter, the diodes of the converter also turn off with a minimized reverse recovery power loss because of the controlled current falling rate of these diodes with the leakage inductance of the CI. The operation principle, steady-state analysis, and comparison are presented in this article. Also, the analysis is verified using a 200 W, and 20 V to 400 V experimental setup.


  • A General Method for Analyzing Single-Switch Step- Up DC–DC Converters With Switched-Capacitor Cells and an Output Inductor

    by Saeed Habibi, Ramin Rahimi, Mehdi Ferdowsi, Pourya Shamsi

    Integration of the voltage multiplier cells (VMC) to conventional step-up converters provides a higher voltage gain and a lower voltage stress on the power switch. However, the output diode of the VMC cells usually withstands a high voltage stress, which may cause reverse recovery power loss and electromagnetic interference (EMI) issues. Also, the pulsating current of the output capacitor increases the required capacitance at the output. In this paper, replacing the output diode of the basic VMCs with an inductor is investigated, and general forms of the voltage gain equations are derived. Moreover, the effects of the inductor value on the circuit operation are explored. Furthermore, the integration of the input and output inductors into one core has also been studied, showing that VMCs integrated into a conventional boost converter could achieve zero current ripple at input by using a coupled inductor. To validate the analysis, a 200 W, 40 V to 200 V experimental setup is developed in the laboratory and the experimental results when using a diode and an inductor at the output of a VMC are presented.


  • Coupled Inductor-Based Single-Switch Quadratic High Step-Up DC–DC Converters With Reduced Voltage Stress on Switch

    by Saeed Habibi, Ramin Rahimi, Mehdi Ferdowsi, Pourya Shamsi

    In this article, two single-switch quadratic boost converters based on a three-winding coupled inductor (CI) are proposed. These converters provide a high voltage gain in a low duty cycle, reduced voltage stress on the power switch, continuous input current with a low di/dt, higher design flexibility, and limited current falling rate on the voltage multiplier diodes to minimize the reverse recovery loss. Moreover, the first proposed converter has two capacitors in the output reducing the need for a bulky output capacitor, while the second proposed converter has higher utilization of the CI and is able to provide a higher voltage gain. The operation principle and theoretical analysis, such as voltage stress, current stress, effect of leakage inductances on the voltage gain, and design considerations are presented in this article. Furthermore, the superiority of the proposed converters over the competitive high step-up quadratic converters are justified through a comparison study. Finally, a 300-W, 30- to 400-V laboratory experimental setup is implemented to validate the theoretical analysis.


  • A Three-Winding Coupled-Inductor-Based Dual-Switch High Step-Up DC–DC Converter for Photovoltaic Systems

    by Ramin Rahimi, Saeed Habibi, Pourya Shamsi, Mehdi Ferdowsi

    This paper proposes a new high step-up DC-DC converter for photovoltaic (PV) applications. A dual-switch structure with a three-winding coupled inductor (3WCI), whose secondary and tertiary windings are integrated with switched-capacitor (SC) cells, is adopted to achieve a high-voltage gain with a small duty cycle, thus avoiding an extremely high duty cycle. The input current is continuous, and the voltage gain could be adjusted by two parameters: the switches' duty cycle and 3WCI's turns-ratio, thus increasing the design flexibility of the proposed converter. In addition, low-voltage-rated MOSFETs with small ON-state resistances are selected, and their losses are reduced due to the low voltage stress and small duty cycle of the switches. Moreover, the current-falling rates of most diodes are controlled by the 3WCI's leakage inductances. The operating modes, detailed analyses, and design considerations for the proposed converter are presented. Additionally, comparisons with other high step-up converters are provided. A 200-W laboratory prototype with an output voltage of 400 V is fabricated and tested using various input voltages to validate the theoretical analyses.


  • Open Access

    An Interleaved High Step-Up DC-DC Converter Based on Integration of Coupled Inductor and Built-in-Transformer With Switched-Capacitor Cells for Renewable Energy Applications

    by Ramin Rahimi, Saeed Habibi, Mehdi Ferdowsi, Pourya Shamsi

    This paper proposes an interleaved high step-up DC-DC converter with the coupled inductor (CI) and built-in transformer (BIT) for renewable energy applications. Two double-winding (2W) CIs and one triple-winding (3W) BIT are integrated with the switched-capacitor (SC) voltage multiplier cells (VMCs) to achieve high-voltage gains without extreme duty cycles. The CIs and BIT turns-ratios provide two other degrees of freedom—in addition to the duty cycle—to adjust the voltage gain that leads to increased design flexibility. The diodes turn off naturally under the zero-current switching (ZCS) conditions because their current falling rates are controlled by the leakage inductances of the CIs and BIT; therefore, the diodes’ reverse-recovery problems are alleviated. Moreover, employing passive diode-capacitor clamp circuits, the voltage stresses of the switches are limited to a low value far less than the output voltage. Additionally, the leakage inductances energies are recycled and transferred to the output to further extend the voltage gain. Furthermore, due to the interleaved structure, the input current ripple and current stresses of the components are reduced. The proposed converter is analyzed in detail and then compared with similar converters that employed two 2W CIs and one 3W BIT along with passive clamp circuits for the MOSFETs. Finally, to verify the feasibility of the proposed converter, the experimental results of a 200 W prototype with output voltage of 400 V and voltage gain of 25 are presented.


  • Open Access

    An Interleaved Quadratic High Step-Up DC-DC Converter With Coupled Inductor

    by Ramin Rahimi, Saeed Habibi, Mehdi Ferdowsi, Pourya Shamsi

    A new high step-up DC-DC converter for renewable energy applications is proposed in this paper. Employing an interleaved quadratic structure, two two-winding coupled inductors (CIs), and voltage multiplier cells (VMCs), the proposed converter can provide high-voltage gains, continuous input current with low ripple, reduced voltage stresses on semiconductors, common ground between input and output sides, and low numbers of components. In addition, diode-capacitor lossless clamp circuits are utilized to limit the voltage stresses of the power switches and further extend the voltage gain. The operating and steady-state analyses, design considerations, and a comparison with other previously published high step-up converters are presented. Lastly, experimental results of a 400 W prototype with 400 V output voltage are illustrated to verify the theoretical analysis and the functionality of the proposed converter.


  • Z-Source-Based High Step-Up DC–DC Converters for Photovoltaic Applications

    by Ramin Rahimi, Saeed Habibi, Mehdi Ferdowsi, Pourya Shamsi

    This paper proposes three high step-up Z-source (ZS)-based DC-DC converters through integrating the conventional ZS network with switched-capacitor (SC) cells. The proposed converters offer a simple structure with a smooth input current, a high-voltage gain, and low voltage stress on the semiconductor devices. In addition, the proposed converters, unlike some existing ZS-based topologies in the literature, do not impose any limitation on the duty cycle of the power switch. These characteristics make the proposed converters excellent candidates to interface a low-voltage solar photovoltaic (PV) panel with a high-voltage DC bus in PV applications. Among the proposed three converters, the operating principles and steady-state analysis of the one with more components are presented in detail. However, the steady-state voltage and current relationships are also tabulated for two other proposed converters. In addition, design considerations are presented. The performance of the proposed converters is compared against similar existing high step-up DC-DC converters with regards to the component count, normalized voltage stress on the power switch and diodes, and voltage gain. Finally, the theoretical analyses and calculations are validated through experimental results using a 400 W/400 V laboratory prototype.


  • Open Access

    DC Bus Voltage Selection for a Grid-Connected Low-Voltage DC Residential Nanogrid Using Real Data with Modified Load Profiles

    by Saeed Habibi, Ramin Rahimi, Mehdi Ferdowsi, Pourya Shamsi

    This study examines various low voltage levels applied to a direct current residential nanogrid (DC-RNG) with respect to the efficiency and component cost of the system. Due to the significant increase in DC-compatible loads, on-site Photovoltaic (PV) generation, and local battery storage, DC distribution has gained considerable attention in buildings. To provide an accurate evaluation of the DC-RNG’s efficiency and component cost, a one-year load profile of a conventional AC-powered house is considered, and AC appliances’ load profiles are scaled to their equivalent available DC appliances. Based on the modified load profiles, proper wiring schemes, converters, and protection devices are chosen to construct a DC-RNG. The constructed DC-RNG is modeled in MATLAB software and simulations are completed to evaluate the efficiency of each LVDC level. Four LVDC levels—24 V, 48 V, 60 V, and 120 V—are chosen to evaluate the DC-RNG’s efficiency and component cost. Additionally, impacts of adding a battery energy storage unit on the DC-RNG’s efficiency are studied. The results indicate that 60 V battery-less DC-RNG is the most efficient one; however, when batteries are added to the DC-RNG, the 48 V DC distribution becomes the most efficient and cost-effective option.