Lichen Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Lichen Zhang has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Lixiang Zhu
School of Materials Science and Engineering, Beijing Institute of Technology, Beijing 100081, China
3 shared publications - Meishuai Zou
Research Center of Materials Science Beijing Key Laboratory of Construction Tailorable Advanced Functional Materials and Green Applications Beijing Institute of Technology Beijing China
3 shared publications - Shuo Wang
School of Materials Science and Engineering, Beijing Institute of Technology, Beijing 100081, China
3 shared publications - Xiaodong Li
School of Materials Science and Engineering Beijing Institute of Technology Beijing China
3 shared publications - Xiaodong Zhang
School of Materials Science and Engineering, Beijing Institute of Technology, Beijing 100081, China
2 shared publications - Xiaoxuan Wang
School of Materials Science and Engineering, Beijing Institute of Technology, Beijing 100081, China
2 shared publications
Latest Publications
- Open Access
Energetic and Protective Coating via Chemical and Physical Synergism for High Water-Reactive Aluminum Powder
Aluminum powder plays important role in the field of energetic materials. However, it is often vulnerable to oxygen and water due to the high reactivity of aluminum, and it is challenging to build up uniform and passivated coating via existing means. In this work, (Heptadecafluoro-1,1,2,2-tetradecyl) trimethoxysilane (FAS-17) and glycidyl azide polymer (GAP) were used to coat the surface of high water-reactive aluminum powder (w-Al) to form inactivated w-Al@FAS-17@GAP energetic materials, via the synergy of chemical bonding and physical attraction. Thermal reaction tests showed that the exothermic enthalpy of w-Al@FAS-17@GAP was 5.26 times that of w-Al. Ignition tests showed that w-Al@FAS-17@GAP burnt violently at 760 °C, while w-Al could not be ignited even at 950 °C. In addition, the combined coating of FAS-17 and GAP could effectively improve the hydrophobicity and long-term stability of w-Al, which helped to overcome the poor compatibility of w-Al with explosive components. Our work not only displayed an effective routine to synthesize O2/H2O proof Al energetic materials, but also pointed out a synergistically chemical and physical strategy for constructing intact high-performance surfaces.
Open AccessEnergetic and Protective Coating via Chemical and Physical Synergism for High Water-Reactive Aluminum Powder
Aluminum powder plays important role in the field of energetic materials. However, it is often vulnerable to oxygen and water due to the high reactivity of aluminum, and it is challenging to build up uniform and passivated coating via existing means. In this work, (Heptadecafluoro-1,1,2,2-tetradecyl) trimethoxysilane (FAS-17) and glycidyl azide polymer (GAP) were used to coat the surface of high water-reactive aluminum powder (w-Al) to form inactivated w-Al@FAS-17@GAP energetic materials, via the synergy of chemical bonding and physical attraction. Thermal reaction tests showed that the exothermic enthalpy of w-Al@FAS-17@GAP was 5.26 times that of w-Al. Ignition tests showed that w-Al@FAS-17@GAP burnt violently at 760 °C, while w-Al could not be ignited even at 950 °C. In addition, the combined coating of FAS-17 and GAP could effectively improve the hydrophobicity and long-term stability of w-Al, which helped to overcome the poor compatibility of w-Al with explosive components. Our work not only displayed an effective routine to synthesize O2/H2O proof Al energetic materials, but also pointed out a synergistically chemical and physical strategy for constructing intact high-performance surfaces.
- Open Access
Enhanced Hydrogen Generation Performance of Al-Rich Alloys by a Melting-Mechanical Crushing-Ball Milling Method
The main problem for the application of hydrogen generated via hydrolysis of metal alloys is the low hydrogen generation rate (HGR). In this paper, active Al alloys were prepared using a new coupled method-melting-mechanical crushing-mechanical ball milling method to enhance the HGR at room temperature. This method contains three steps, including the melting of Al, Ga, In, and Sn ingots with low melting alloy blocks and casting into plates, then crushing alloy plate into powders and ball milling with chloride salts such as NiCl2 and CoCl2 were added during the ball milling process. The microstructure and phase compositions of Al alloys and reaction products were investigated via X-ray diffraction and scanning electron microscopy with energy dispersed X-ray spectroscopy. The low-melting-point Ga-In -Sn (GIS) phases contain a large amount of Al can act as a transmission medium for Al, which improves the diffusion of Al to Al/H2O reaction sites. Finer GIS phases after ball milling can further enhance the diffusion of Al and thus enhance the activity of Al alloy. The hydrogen generation performance through hydrolysis of water with Al at room temperature was investigated. The results show that the H2 generation performance of the Al-low-melting point alloy composite powder is significantly higher than the results reported to date. The highest H2 generation rate and H2 conversion efficiency can reach 5337 mL·min−1·g−1 for the hydrolysis of water with 1 g active alloy.
Open AccessEnhanced Hydrogen Generation Performance of Al-Rich Alloys by a Melting-Mechanical Crushing-Ball Milling Method
The main problem for the application of hydrogen generated via hydrolysis of metal alloys is the low hydrogen generation rate (HGR). In this paper, active Al alloys were prepared using a new coupled method-melting-mechanical crushing-mechanical ball milling method to enhance the HGR at room temperature. This method contains three steps, including the melting of Al, Ga, In, and Sn ingots with low melting alloy blocks and casting into plates, then crushing alloy plate into powders and ball milling with chloride salts such as NiCl2 and CoCl2 were added during the ball milling process. The microstructure and phase compositions of Al alloys and reaction products were investigated via X-ray diffraction and scanning electron microscopy with energy dispersed X-ray spectroscopy. The low-melting-point Ga-In -Sn (GIS) phases contain a large amount of Al can act as a transmission medium for Al, which improves the diffusion of Al to Al/H2O reaction sites. Finer GIS phases after ball milling can further enhance the diffusion of Al and thus enhance the activity of Al alloy. The hydrogen generation performance through hydrolysis of water with Al at room temperature was investigated. The results show that the H2 generation performance of the Al-low-melting point alloy composite powder is significantly higher than the results reported to date. The highest H2 generation rate and H2 conversion efficiency can reach 5337 mL·min−1·g−1 for the hydrolysis of water with 1 g active alloy.
- Open Access
Preparation of Al-3Ga-3In-3Sn Alloy Powder by Coupling Alloying and Ball Milling and Its Application on High-Rate Hydrogen Generation at Room Temperature
High hydro-active Al-3Ga-3In-3Sn alloys were prepared by coupling alloying and mechanical milling methods. NiCl2 was added to the alloy during ball milling as the catalyst. XRD, SEM, and XAFS were used for the characterization of the hydro-active alloy. The hydrogen generation properties were systematically investigated in tap water at room temperature. The results show that the hydrogen generation rate is 11.02 L∙min−1∙g−1, and the conversion yield is 90.25% for the Al-3Ga-3In-3Sn-2NiCl2 composite with a ball milling time of 2 h at room temperature in tap water. The hydrolysis reaction contains the expansion of the Al-based phase into a nano-sized layer and the further hydrolysis reaction of the layered Al phase with water. The activation mechanism was also investigated, and the activation of Al was attributed to the Al-Ni galvanic with the existing Cl−, which leads to a faster hydrolysis reaction rate for ball-milled powder with NiCl2.
Open AccessPreparation of Al-3Ga-3In-3Sn Alloy Powder by Coupling Alloying and Ball Milling and Its Application on High-Rate Hydrogen Generation at Room Temperature
High hydro-active Al-3Ga-3In-3Sn alloys were prepared by coupling alloying and mechanical milling methods. NiCl2 was added to the alloy during ball milling as the catalyst. XRD, SEM, and XAFS were used for the characterization of the hydro-active alloy. The hydrogen generation properties were systematically investigated in tap water at room temperature. The results show that the hydrogen generation rate is 11.02 L∙min−1∙g−1, and the conversion yield is 90.25% for the Al-3Ga-3In-3Sn-2NiCl2 composite with a ball milling time of 2 h at room temperature in tap water. The hydrolysis reaction contains the expansion of the Al-based phase into a nano-sized layer and the further hydrolysis reaction of the layered Al phase with water. The activation mechanism was also investigated, and the activation of Al was attributed to the Al-Ni galvanic with the existing Cl−, which leads to a faster hydrolysis reaction rate for ball-milled powder with NiCl2.