Sasa Gao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Sasa Gao has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
Hongzhe Zhai
Shaanxi Univ Sci & Technol, Sch Mech & Elect Engn, Xian 710021, Peoples R China
2 shared publications- Junhong Jia
College of Mechanical and Electrical Engineering Shaanxi University of Science & Technology Xi'an P. R. China
2 shared publications Wenjie Zhang
Shaanxi Univ Sci & Technol, Sch Mech & Elect Engn, Xian 710021, Peoples R China
2 shared publicationsXuepeng Gong
Chinese Acad Sci, Key Lab Opt Syst Adv Mfg Technol, Changchun 130033, Peoples R China
2 shared publicationsYunjie Zhang
2 shared publicationsZeyu Wang
College of Mechanical & Electrical Engineering, Shaanxi University of Science & Technology, Xi’an, China
2 shared publications
Latest Publications
- 2 September 2024
- Published by Springer Nature in Applied Composite Materials
- Vol. 32 (1) , 199-213
Numerical Simulation and Preforming Parameters Optimization of Carbon-Kevlar Hybrid Woven Reinforcement Materials Based on Genetic Algorithm
- 2 September 2024
- Published by Springer Nature in Applied Composite Materials
- Vol. 32 (1) , 199-213
Numerical Simulation and Preforming Parameters Optimization of Carbon-Kevlar Hybrid Woven Reinforcement Materials Based on Genetic Algorithm
- 10 February 2024
- Published by Elsevier in Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment
- Vol. 1062
Numerical study of the influence of two-phase flow with different inlet velocities on the angular stability of double crystal monochromator
- 10 February 2024
- Published by Elsevier in Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment
- Vol. 1062
Numerical study of the influence of two-phase flow with different inlet velocities on the angular stability of double crystal monochromator
- Open Access
- 1 January 2024
- Published by National Library of Serbia in Thermal Science
- Vol. 28 (1 Part A) , 257-267
The influence of corrugated pipes parameters on heat transfer characteristics
In order to investigate the influence mechanism of various corrugated structures on the heat transfer of continuous annular concave-convex corrugated pipes, this paper examines the influence of corrugation height (Ch=1, 1.5 and 2 mm) and corrugation width (Cw=1, 1.5 and 2 mm) on the flow pattern, turbulent kinetic energy(TKE), Nusselt number (Nu), friction coefficient (f), and performance evaluation factor (PEF). Then, the correlation equations for Nu and f are established with different corrugated structural parameters. The results show that with the increase of Ch, the vortex number, TKE, and fin the pipe increase while Nude creases. The maximum PEF is 0.90 at Ch=1 mm. However, with the increase of Cw, the vortex number and Nuin the pipe increase, while TKE and fin the pipe do not change much. The maximum PEF is 0.87 at Cw=2 mm. Therefore, for this type of corrugated pipe, one should choose a small Chand a large Cw.
- 1 January 2024
- Published by National Library of Serbia in Thermal Science
- Vol. 28 (1 Part A) , 257-267
Open AccessThe influence of corrugated pipes parameters on heat transfer characteristics
In order to investigate the influence mechanism of various corrugated structures on the heat transfer of continuous annular concave-convex corrugated pipes, this paper examines the influence of corrugation height (Ch=1, 1.5 and 2 mm) and corrugation width (Cw=1, 1.5 and 2 mm) on the flow pattern, turbulent kinetic energy(TKE), Nusselt number (Nu), friction coefficient (f), and performance evaluation factor (PEF). Then, the correlation equations for Nu and f are established with different corrugated structural parameters. The results show that with the increase of Ch, the vortex number, TKE, and fin the pipe increase while Nude creases. The maximum PEF is 0.90 at Ch=1 mm. However, with the increase of Cw, the vortex number and Nuin the pipe increase, while TKE and fin the pipe do not change much. The maximum PEF is 0.87 at Cw=2 mm. Therefore, for this type of corrugated pipe, one should choose a small Chand a large Cw.
Effect of woven yarn angle on the low‐velocity impact damage response of fibre woven thermoplastic composites
Fibre woven thermoplastic composites (FWTC) are widely used in aerospace and other fields because of their excellent performance. During service, FWTC structures are inevitably subjected to low‐velocity impact (LVI), which can cause invisible damage and eventual failure of the material. At the moment, studies on FWTC mostly focused on the orthogonal woven yarns while there's few reports about the effect of the yarn angle changing on the woven material's LVI damage response. This study aims at the effect of yarn angle changing on the damage behaviour of FWTC. A method for preparation of nonorthogonal prepregs was proposed, by which FWTC laminates with different yarn angles (60°, 75°, and 90°) were prepared for LVI tests. The results show that the maximum impact displacement and the impact duration of the impactor decrease with the decrease of the yarn angle when the FWTC laminate is subjected to LVI, while the maximum impact force shows an increasing trend. This indicates that the smaller yarn angle causes the better load‐bearing capacity of the FWTC laminate under LVI conditions, while the orthogonal FWTC laminate is more ductile. The damage morphology indicated by the impact of the FWTC laminate are matrix cracks and yarn breaks, and the damage area increases with the decrease of yarn angle, where the damage of orthogonal laminate is more serious more concentrated. The results found in this paper can provide useful guidance for engineering applications and failure analysis of FWTC.
Effect of woven yarn angle on the low‐velocity impact damage response of fibre woven thermoplastic composites
Fibre woven thermoplastic composites (FWTC) are widely used in aerospace and other fields because of their excellent performance. During service, FWTC structures are inevitably subjected to low‐velocity impact (LVI), which can cause invisible damage and eventual failure of the material. At the moment, studies on FWTC mostly focused on the orthogonal woven yarns while there's few reports about the effect of the yarn angle changing on the woven material's LVI damage response. This study aims at the effect of yarn angle changing on the damage behaviour of FWTC. A method for preparation of nonorthogonal prepregs was proposed, by which FWTC laminates with different yarn angles (60°, 75°, and 90°) were prepared for LVI tests. The results show that the maximum impact displacement and the impact duration of the impactor decrease with the decrease of the yarn angle when the FWTC laminate is subjected to LVI, while the maximum impact force shows an increasing trend. This indicates that the smaller yarn angle causes the better load‐bearing capacity of the FWTC laminate under LVI conditions, while the orthogonal FWTC laminate is more ductile. The damage morphology indicated by the impact of the FWTC laminate are matrix cracks and yarn breaks, and the damage area increases with the decrease of yarn angle, where the damage of orthogonal laminate is more serious more concentrated. The results found in this paper can provide useful guidance for engineering applications and failure analysis of FWTC.
- Open Access
- 1 June 2022
- Published by Elsevier in Chinese Journal of Aeronautics
- Vol. 35 (6) , 367-378
An integrated preforming-performance model for high-fidelity performance analysis of cured woven composite part with non-orthogonal yarn angles
- 1 June 2022
- Published by Elsevier in Chinese Journal of Aeronautics
- Vol. 35 (6) , 367-378
Open AccessAn integrated preforming-performance model for high-fidelity performance analysis of cured woven composite part with non-orthogonal yarn angles
- Open Access
The Surface Characteristics, Microstructure and Mechanical Properties of PEEK Printed by Fused Deposition Modeling with Different Raster Angles
Additive manufacturing provides a novel and robust way to prepare medical product with anatomic matched geometry and tailored mechanical performance. In this study, the surface characteristics, microstructure, and mechanical properties of fused deposition modeling (FDM) prepared polyether-ether-ketone (PEEK) were systematically studied. During the FDM process, the crystal unit cell and thermal attribute of PEEK material remained unchanged, whereas the surface layer generally became more hydrophilic with an obvious reduction in surface hardness. Raster angle has a significant effect on the mechanical strength but not on the failure mechanism. In practice, FDM fabricated PEEK acted more like a laminate rather than a unified structure. Its main failure mechanism was correlated to the internal voids. The results show that horizontal infill orientation with 30° raster angle is promising for a better comprehensive mechanical performance, and the corresponding tensile, flexural, and shear strengths are (76.5 ± 1.4) MPa, (149.7 ± 3.0) MPa, and (55.5 ± 1.8) MPa, respectively. The findings of this study provide guidelines for FDM-PEEK to enable its realization in applications such as orthopedic implants.
Open AccessThe Surface Characteristics, Microstructure and Mechanical Properties of PEEK Printed by Fused Deposition Modeling with Different Raster Angles
Additive manufacturing provides a novel and robust way to prepare medical product with anatomic matched geometry and tailored mechanical performance. In this study, the surface characteristics, microstructure, and mechanical properties of fused deposition modeling (FDM) prepared polyether-ether-ketone (PEEK) were systematically studied. During the FDM process, the crystal unit cell and thermal attribute of PEEK material remained unchanged, whereas the surface layer generally became more hydrophilic with an obvious reduction in surface hardness. Raster angle has a significant effect on the mechanical strength but not on the failure mechanism. In practice, FDM fabricated PEEK acted more like a laminate rather than a unified structure. Its main failure mechanism was correlated to the internal voids. The results show that horizontal infill orientation with 30° raster angle is promising for a better comprehensive mechanical performance, and the corresponding tensile, flexural, and shear strengths are (76.5 ± 1.4) MPa, (149.7 ± 3.0) MPa, and (55.5 ± 1.8) MPa, respectively. The findings of this study provide guidelines for FDM-PEEK to enable its realization in applications such as orthopedic implants.
- Open Access
Analysis of the Mechanical and Preforming Behaviors of Carbon-Kevlar Hybrid Woven Reinforcement
Carbon-Kevlar hybrid reinforcement is increasingly used in the domains that have both strength and anti-impact requirements. However, the research on the preforming behaviors of hybrid reinforcement is very limited. This paper aims to investigate the mechanical and preforming behaviors of carbon-Kevlar hybrid reinforcement. The results show that carbon-Kevlar hybrid woven reinforcement presents a unique “double-peak” tensile behavior, which is significantly different from that of single fiber type reinforcement, and the in-plane shear deformation demonstrates its large in-plane shear deformability. Both the tensile and in-plane shear behaviors present insensitivity to loading rate. In the preforming process, yarn slippage and out-of-plane yarn buckling are the two primary types of defects. Locations of these defects are closely related to the punch shape and the initial yarn direction. These defects cannot be alleviated or removed by just increasing the blank holder pressure. In the multi-layer preforming, the compaction between the plies and the friction between yarns simultaneously affect the quality of final preforms. The defect location of multi-layer preforms is the same as that of single-layer, while its defect range is much wider. The results found in this paper could provide useful guidance for the engineering application and preforming modeling of hybrid woven reinforcement.
Open AccessAnalysis of the Mechanical and Preforming Behaviors of Carbon-Kevlar Hybrid Woven Reinforcement
Carbon-Kevlar hybrid reinforcement is increasingly used in the domains that have both strength and anti-impact requirements. However, the research on the preforming behaviors of hybrid reinforcement is very limited. This paper aims to investigate the mechanical and preforming behaviors of carbon-Kevlar hybrid reinforcement. The results show that carbon-Kevlar hybrid woven reinforcement presents a unique “double-peak” tensile behavior, which is significantly different from that of single fiber type reinforcement, and the in-plane shear deformation demonstrates its large in-plane shear deformability. Both the tensile and in-plane shear behaviors present insensitivity to loading rate. In the preforming process, yarn slippage and out-of-plane yarn buckling are the two primary types of defects. Locations of these defects are closely related to the punch shape and the initial yarn direction. These defects cannot be alleviated or removed by just increasing the blank holder pressure. In the multi-layer preforming, the compaction between the plies and the friction between yarns simultaneously affect the quality of final preforms. The defect location of multi-layer preforms is the same as that of single-layer, while its defect range is much wider. The results found in this paper could provide useful guidance for the engineering application and preforming modeling of hybrid woven reinforcement.