Wenli Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Wenli Zhang has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
Le Fan
National Synchrotron Radiation Laboratory, University of Science and Technology of China, Hefei, Anhui 230029, China
6 shared publications- Sihui Wang
National Synchrotron Radiation Laboratory, University of Science and Technology of China 1 , Hefei, Anhui 230029
6 shared publications Yuanzhi Hong
6 shared publicationsYong Wang
National Synchrotron Radiation Laboratory, University of Science and Technology of China, Hefei, Anhui 230029, China
5 shared publications- Bangle Zhu
National Synchrotron Radiation Laboratory, University of Science and Technology of China, Hefei, China
3 shared publications Tao Huang
National Synchrotron Radiation Laboratory, University of Science and Technology of China, Hefei, Anhui 230029, China
3 shared publications
Latest Publications
- 1 February 2025
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 20 (02) , T02002
Photon-stimulated desorption from laser-etched vacuum structural materials of accelerators
The electron multipacting (EM) and the electron cloud (e-cloud) can have detrimental impact on the operation of the high energy or high current intensity particle accelerators. The enhanced performance of new generation particle accelerators has necessitated the development of advanced structural materials and vacuum systems. The EM and e-cloud effect have emerged as significant challenges which cannot be ignored during the design and construction of these advanced accelerators. Laser-etching technique represents a promising approach for the suppression of secondary electron emission from materials, which can lower the secondary electron yield (SEY) of the structural materials to below 1. Nevertheless, the deployment of laser-etching technique in the next generation of large particle accelerators requires a comprehensive investigation into its vacuum performance. In this work, a photo-stimulated desorption (PSD) experimental beamline was constructed on the Hefei Light Source II. The PSD yields of the structural materials (oxygen-free copper, chrome zirconium copper, stainless steel, and aluminum alloy) with and without laser-etching of the vacuum chambers were tested at normal incidence using the throughput method. The main gases desorbed from all sample surfaces are H2, CO, CO2, CH4, and H2O. The initial PSD yield of laser-etched material is higher than that of unetched material. However, the PSD yield of the laser-etched material decreases at a faster rate, and after a certain photon dose, the PSD yield of the laser-etched material is in the same order of magnitude as that of the unetched material.
- 1 February 2025
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 20 (02) , T02002
Photon-stimulated desorption from laser-etched vacuum structural materials of accelerators
The electron multipacting (EM) and the electron cloud (e-cloud) can have detrimental impact on the operation of the high energy or high current intensity particle accelerators. The enhanced performance of new generation particle accelerators has necessitated the development of advanced structural materials and vacuum systems. The EM and e-cloud effect have emerged as significant challenges which cannot be ignored during the design and construction of these advanced accelerators. Laser-etching technique represents a promising approach for the suppression of secondary electron emission from materials, which can lower the secondary electron yield (SEY) of the structural materials to below 1. Nevertheless, the deployment of laser-etching technique in the next generation of large particle accelerators requires a comprehensive investigation into its vacuum performance. In this work, a photo-stimulated desorption (PSD) experimental beamline was constructed on the Hefei Light Source II. The PSD yields of the structural materials (oxygen-free copper, chrome zirconium copper, stainless steel, and aluminum alloy) with and without laser-etching of the vacuum chambers were tested at normal incidence using the throughput method. The main gases desorbed from all sample surfaces are H2, CO, CO2, CH4, and H2O. The initial PSD yield of laser-etched material is higher than that of unetched material. However, the PSD yield of the laser-etched material decreases at a faster rate, and after a certain photon dose, the PSD yield of the laser-etched material is in the same order of magnitude as that of the unetched material.
Effect of activation temperature on photon-stimulated desorption from Ti-Zr-V coated copper chambers
- 30 December 2023
- Published by Elsevier in Applied Surface Science
- Vol. 651
Effect of thermal cycling on microstructure and adhesion properties of Ti-Zr-V thin films
- 30 December 2023
- Published by Elsevier in Applied Surface Science
- Vol. 651
Effect of thermal cycling on microstructure and adhesion properties of Ti-Zr-V thin films
- 13 September 2022
- Published by Elsevier in Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment
- Vol. 1042
Experimental research on the longitudinal coupling impedance of RF-shielded BPM-bellows assemblies designed for the Hefei Advanced Light Facility
- 13 September 2022
- Published by Elsevier in Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment
- Vol. 1042
Experimental research on the longitudinal coupling impedance of RF-shielded BPM-bellows assemblies designed for the Hefei Advanced Light Facility
- 6 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1 (21645221) , 327-332
An Occlusion-Aware RGB-D Visual Object Tracking Method Based on Siamese Network
In recent years, Siamese trackers have been extensively studied because of their high accuracy and speed. However, when the target is occluded by other objects, the result will be greatly drifted, which affects the quality of the tracking results. This study based on the RGB-D data proposes an object tracking method integrating a target occlusion estimation module and a target location correction module, called Siamese-Occlusion-Correction (SiamOC). When a target is occluded, these modules can help the Siamese tracker correct the target location. In this paper, experiments demonstrate that the method which is the real-time tracker has achieved competitive results on the CDTB dataset.
- 6 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1 (21645221) , 327-332
An Occlusion-Aware RGB-D Visual Object Tracking Method Based on Siamese Network
In recent years, Siamese trackers have been extensively studied because of their high accuracy and speed. However, when the target is occluded by other objects, the result will be greatly drifted, which affects the quality of the tracking results. This study based on the RGB-D data proposes an object tracking method integrating a target occlusion estimation module and a target location correction module, called Siamese-Occlusion-Correction (SiamOC). When a target is occluded, these modules can help the Siamese tracker correct the target location. In this paper, experiments demonstrate that the method which is the real-time tracker has achieved competitive results on the CDTB dataset.