Dan Meng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Dan Meng has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
Jing Liu
Jimei University
4 shared publicationsChao Dou
Jimei University
2 shared publications- Wen-Zhuang Ma
Jimei University
2 shared publications Xuchu Deng
Jimei University
2 shared publicationsYu-Shan Chen
2 shared publications- Changgui Lu
Advanced Photonics Center, School of Electronic Science & Engineering, Southeast University, Nanjing 210018, China
1 shared publication
Latest Publications
- 16 September 2025
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 27 (39) , 21059-21069
Universal terahertz trace molecular fingerprint sensing based on high-degree-of-freedom dielectric metagrating
A dielectric metagrating metasensor combining guided mode resonance and quasi-BIC enables broadband, high-sensitivity terahertz molecular fingerprint detection with multiplexing strategies for practical biosensing and chemical analysis.
- 16 September 2025
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 27 (39) , 21059-21069
Universal terahertz trace molecular fingerprint sensing based on high-degree-of-freedom dielectric metagrating
A dielectric metagrating metasensor combining guided mode resonance and quasi-BIC enables broadband, high-sensitivity terahertz molecular fingerprint detection with multiplexing strategies for practical biosensing and chemical analysis.
- 18 April 2023
- Published by Optica Publishing Group in Optics Express
- Vol. 31 (9) , 14495-14508
All-day uninterrupted thermoelectric generator by simultaneous harvesting of solar heating and radiative cooling
Passive power generation has recently stimulated interest in thermoelectric generators (TEGs) using the radiative cooling mechanism. However, the limited and unstable temperature difference across the TEGs significantly degrades the output performance. In this study, an ultra-broadband solar absorber with a planar film structure is introduced as the hot side of the TEG to increase the temperature difference by utilizing solar heating. This device not only enhances the generation of electrical power but also realizes all-day uninterrupted electrical output due to the stable temperature difference between the cold and hot sides of the TEG. Outdoor experiments show the self-powered TEG obtains maximum temperature differences of 12.67 °C, 1.06 °C, and 5.08 °C during sunny daytime, clear nighttime, and cloudy daytime, respectively, and generates output voltages of 166.2 mV, 14.7 mV, and 95 mV, respectively. Simultaneously, the corresponding output powers of 879.25 mW/m2, 3.85 mW/m2, and 287.27 mW/m2 are produced, achieving 24-hour uninterrupted passive power generation. These findings propose a novel strategy to combine solar heating and outer space cooling by a selective absorber/emitter to generate all-day continuous electricity for unsupervised small devices.
- 18 April 2023
- Published by Optica Publishing Group in Optics Express
- Vol. 31 (9) , 14495-14508
All-day uninterrupted thermoelectric generator by simultaneous harvesting of solar heating and radiative cooling
Passive power generation has recently stimulated interest in thermoelectric generators (TEGs) using the radiative cooling mechanism. However, the limited and unstable temperature difference across the TEGs significantly degrades the output performance. In this study, an ultra-broadband solar absorber with a planar film structure is introduced as the hot side of the TEG to increase the temperature difference by utilizing solar heating. This device not only enhances the generation of electrical power but also realizes all-day uninterrupted electrical output due to the stable temperature difference between the cold and hot sides of the TEG. Outdoor experiments show the self-powered TEG obtains maximum temperature differences of 12.67 °C, 1.06 °C, and 5.08 °C during sunny daytime, clear nighttime, and cloudy daytime, respectively, and generates output voltages of 166.2 mV, 14.7 mV, and 95 mV, respectively. Simultaneously, the corresponding output powers of 879.25 mW/m2, 3.85 mW/m2, and 287.27 mW/m2 are produced, achieving 24-hour uninterrupted passive power generation. These findings propose a novel strategy to combine solar heating and outer space cooling by a selective absorber/emitter to generate all-day continuous electricity for unsupervised small devices.
- 14 February 2023
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 13 (3) , 656-666
Study of a perfect solar absorber from the visible to the near-infrared band using particle swarm optimization
In this study, we simulate how much solar energy a proposed planar dielectric-metal (SiO2-Ti-SiO2-Ti-SiO2-Ti-SiO2-W) structure can absorb by employing FDTD solutions. The proposed structure is ultrathin (510.1 nm). It can absorb incident light within a wavelength range of 345 to at least 2500 nm with an average absorption of 97.8% for the incident light in the 345–2500 nm band while maintaining efficient absorption for a wide range of incident light when its angle changes and being insensitive to the polarization angle of the incident light. In addition, the Particle Swarm Optimization algorithm was used to optimize the proposed planar structure, and the optimality of the 8-layer structure was investigated. In addition, we compare the proposed structure to those of others, analyze the reasons for the structure's perfect absorption, and discuss the resonance mode that occurs during the absorption process, which demonstrates the rationale behind its perfect absorption. As a result, the proposed device can efficiently and sustainably collect solar energy.
- 14 February 2023
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 13 (3) , 656-666
Study of a perfect solar absorber from the visible to the near-infrared band using particle swarm optimization
In this study, we simulate how much solar energy a proposed planar dielectric-metal (SiO2-Ti-SiO2-Ti-SiO2-Ti-SiO2-W) structure can absorb by employing FDTD solutions. The proposed structure is ultrathin (510.1 nm). It can absorb incident light within a wavelength range of 345 to at least 2500 nm with an average absorption of 97.8% for the incident light in the 345–2500 nm band while maintaining efficient absorption for a wide range of incident light when its angle changes and being insensitive to the polarization angle of the incident light. In addition, the Particle Swarm Optimization algorithm was used to optimize the proposed planar structure, and the optimality of the 8-layer structure was investigated. In addition, we compare the proposed structure to those of others, analyze the reasons for the structure's perfect absorption, and discuss the resonance mode that occurs during the absorption process, which demonstrates the rationale behind its perfect absorption. As a result, the proposed device can efficiently and sustainably collect solar energy.
- Open Access
- 2 February 2023
- Published by Elsevier in Results in Physics
- Vol. 46
Polyethylene terephthalate-based colored emitters for efficient daytime radiative cooling
- 2 February 2023
- Published by Elsevier in Results in Physics
- Vol. 46
Open AccessPolyethylene terephthalate-based colored emitters for efficient daytime radiative cooling
- 26 October 2021
- Published by Optica Publishing Group in Optics Express
- Vol. 29 (23) , 37234-37244
Fingerprint detection in the mid-infrared region based on guided-mode resonance and phonon-polariton coupling of analyte
Mid-infrared absorption spectroscopy is an effective method for detecting analyte fingerprints without labeling, but the inherent loss of metals in current methods is a main issue. Here, a sensing scheme was proposed that uses an all-dielectric grating metasurface and angular scanning of polarized light, and then it was verified by numerical simulation. The proposed fingerprint detection scheme could effectively couple a guided-mode resonance spectrum peak with the characteristic peak of the analyte’s phonon-polariton in the mid-infrared region, significantly enhancing the interaction between light and the analyte. The novel scheme would realize broadband enhancement to detect a variety of substances, and facilitate mid-infrared sensing and analysis of trace substances.
- 26 October 2021
- Published by Optica Publishing Group in Optics Express
- Vol. 29 (23) , 37234-37244
Fingerprint detection in the mid-infrared region based on guided-mode resonance and phonon-polariton coupling of analyte
Mid-infrared absorption spectroscopy is an effective method for detecting analyte fingerprints without labeling, but the inherent loss of metals in current methods is a main issue. Here, a sensing scheme was proposed that uses an all-dielectric grating metasurface and angular scanning of polarized light, and then it was verified by numerical simulation. The proposed fingerprint detection scheme could effectively couple a guided-mode resonance spectrum peak with the characteristic peak of the analyte’s phonon-polariton in the mid-infrared region, significantly enhancing the interaction between light and the analyte. The novel scheme would realize broadband enhancement to detect a variety of substances, and facilitate mid-infrared sensing and analysis of trace substances.
- 1 December 2020
- Published by Elsevier in Applied Surface Science
- Vol. 534, 147632
Dual-function of CdCl2 treated SnO2 in Sb2Se3 solar cells
- 1 December 2020
- Published by Elsevier in Applied Surface Science
- Vol. 534, 147632
Dual-function of CdCl2 treated SnO2 in Sb2Se3 solar cells