Jiongjie Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jiongjie Liu has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Ralf Riedel
Institute of Materials Science Technical University of Darmstadt Darmstadt Germany
5 shared publications - Emanuel Ionescu
Institut für Materialwissenschaft Technische Universität Darmstadt Darmstadt Germany
3 shared publications - Emmanuel Ricohermoso
Fachbereich Material-Und Geowissenschaften, Technische Universität Darmstadt, Darmstadt, Germany
3 shared publications Wei Li
Institute of Materials Science Technical University of Darmstadt Darmstadt Germany
2 shared publicationsZhuhui Qiao
2 shared publicationsAnke Weidenkaff
Institute of Materials Science Technical University of Darmstadt Darmstadt Germany
1 shared publication
Latest Publications
- 23 December 2023
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 44 (5) , 3065-3073
Preparation of polymer-derived SiOC-Cu ceramic composites and their tribological performance
- 23 December 2023
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 44 (5) , 3065-3073
Preparation of polymer-derived SiOC-Cu ceramic composites and their tribological performance
- Open Access
- 18 April 2023
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 106 (8) , 4931-4943
Temperature‐dependent mechanical and oxidation behavior of in situ formed ZrN/ZrO 2 ‐containing Si 3 N 4 ‐based composite
In this work, Si 3 N 4 and Zr(NO 3 ) 4 were used as raw materials to prepare ZrN/ZrO 2 ‐containing Si 3 N 4 ‐based ceramic composite. The processing, phase composition, and microstructure of the composite were investigated. Hardness and fracture toughness of the ceramics were evaluated via Vickers indentation in Ar at 25°C, 300°C, 600°C, and 900°C. During spark plasma sintering, Zr(NO 3 ) 4 was transformed into tetragonal ZrO 2 , which further reacted with Si 3 N 4 , resulting in the formation of ZrN. The introduction of ZrN enhanced the high‐temperature mechanical properties of the composite, and its hardness and fracture toughness reached 13.4 GPa and 6.1 MPa·m 1/2 at 900°C, respectively. The oxidation experiment was carried out in air at 1000°C, 1300°C, and 1500°C for 5 h. It was shown that high‐temperature oxidation promoted the formation and growth of porous oxide layers. The microstructure and phase composition of the formed oxide layers were investigated in detail. Finally, it was identified that the obtained composite exhibited a higher thermal diffusivity than that of monolithic Si 3 N 4 in the temperature range of 100°C–1000°C.
- 18 April 2023
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 106 (8) , 4931-4943
Open AccessTemperature‐dependent mechanical and oxidation behavior of in situ formed ZrN/ZrO 2 ‐containing Si 3 N 4 ‐based composite
In this work, Si 3 N 4 and Zr(NO 3 ) 4 were used as raw materials to prepare ZrN/ZrO 2 ‐containing Si 3 N 4 ‐based ceramic composite. The processing, phase composition, and microstructure of the composite were investigated. Hardness and fracture toughness of the ceramics were evaluated via Vickers indentation in Ar at 25°C, 300°C, 600°C, and 900°C. During spark plasma sintering, Zr(NO 3 ) 4 was transformed into tetragonal ZrO 2 , which further reacted with Si 3 N 4 , resulting in the formation of ZrN. The introduction of ZrN enhanced the high‐temperature mechanical properties of the composite, and its hardness and fracture toughness reached 13.4 GPa and 6.1 MPa·m 1/2 at 900°C, respectively. The oxidation experiment was carried out in air at 1000°C, 1300°C, and 1500°C for 5 h. It was shown that high‐temperature oxidation promoted the formation and growth of porous oxide layers. The microstructure and phase composition of the formed oxide layers were investigated in detail. Finally, it was identified that the obtained composite exhibited a higher thermal diffusivity than that of monolithic Si 3 N 4 in the temperature range of 100°C–1000°C.
- 16 February 2023
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 43 (8) , 3191-3200
Polymer-derived SiOC ceramics: A potential catalyst support controlled by the sintering temperature and carbon content
- 16 February 2023
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 43 (8) , 3191-3200
Polymer-derived SiOC ceramics: A potential catalyst support controlled by the sintering temperature and carbon content
- 1 May 2022
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 42 (5) , 1955-1962
Phase composition, microstructure, and mechanical properties of polymer-derived SiOC glass-ceramics reinforced by WC particles
- 1 May 2022
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 42 (5) , 1955-1962
Phase composition, microstructure, and mechanical properties of polymer-derived SiOC glass-ceramics reinforced by WC particles
- 1 March 2022
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 42 (3) , 913-920
Sn-containing Si3N4-based composites for adaptive excellent friction and wear in a wide temperature range
- 1 March 2022
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 42 (3) , 913-920
Sn-containing Si3N4-based composites for adaptive excellent friction and wear in a wide temperature range