Saeideh Naghdali
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Saeideh Naghdali has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Mehdi Malekan
School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, Tehran, Iran
2 shared publications - Christoph Czettl
CERATIZIT Austria GmbH, Metallwerk-Plansee-Straße 71, 6600 Reutte, Austria
1 shared publication Daniel Primetzhofer
Department of Physics and Astronomy, Uppsala University, Lägerhyddsvägen 1, 75120 Uppsala, Sweden
1 shared publication- Hassan Jafari
Materials Engineering Department, Faculty of Materials Engineering and Interdisciplinary Sciences, Shahid Rajaee Teacher Training University (SRTTU), Tehran, Iran
1 shared publication Helene Waldl
Christian Doppler Laboratory for Advanced Coated Cutting Tools at the Department of Materials Science, Montanuniversität Leoben, Franz Josef-Straße 18, 8700 Leoben, Austria
1 shared publication- Helene Waldl
Christian Doppler Laboratory for Advanced Coated Cutting Tools, Department of Materials Science, Montanuniversität Leoben, Franz Josef-Straße 18, 8700 Leoben, Austria
1 shared publication
Latest Publications
- Open Access
High-Resolution Investigation of the Interfaces in Cathodic Arc Evaporated TiN/CrAlN Multilayer Coatings
TiN/CrAlN multilayer coatings were synthesized by cathodic arc deposition using 2-fold substrate rotation and alternating targets. The effect of substrate rotation on the layer sequence, elemental fluctuations and interface quality was examined using high-resolution transmission electron microscopy and atom probe tomography. The layers exhibited semi-coherent growth across the interfaces. Minor interface roughness and elemental intermixing limited to below 2 nm at the interface could be observed. Further, the formation of a Ti-enriched sublayer in the Cr1−xAlxN as a result of the 2-fold rotation was identified.
Open AccessHigh-Resolution Investigation of the Interfaces in Cathodic Arc Evaporated TiN/CrAlN Multilayer Coatings
TiN/CrAlN multilayer coatings were synthesized by cathodic arc deposition using 2-fold substrate rotation and alternating targets. The effect of substrate rotation on the layer sequence, elemental fluctuations and interface quality was examined using high-resolution transmission electron microscopy and atom probe tomography. The layers exhibited semi-coherent growth across the interfaces. Minor interface roughness and elemental intermixing limited to below 2 nm at the interface could be observed. Further, the formation of a Ti-enriched sublayer in the Cr1−xAlxN as a result of the 2-fold rotation was identified.
- Open Access
- 17 June 2025
- Published by Elsevier in Ultramicroscopy
- Vol. 276, 114200
Improving the elemental and imaging accuracy in atom probe tomography of (Ti,Si)N single and multilayer coatings using isotopic substitution of N
- 17 June 2025
- Published by Elsevier in Ultramicroscopy
- Vol. 276, 114200
Open AccessImproving the elemental and imaging accuracy in atom probe tomography of (Ti,Si)N single and multilayer coatings using isotopic substitution of N
- Open Access
- 1 November 2021
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 15, 4981-4992
Effect of thixoforming and precipitation hardening on microstructure and mechanical properties of Al-10.5Si–3Cu-0.2Mg alloy produced by strain induced melt activation process
- 1 November 2021
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 15, 4981-4992
Open AccessEffect of thixoforming and precipitation hardening on microstructure and mechanical properties of Al-10.5Si–3Cu-0.2Mg alloy produced by strain induced melt activation process
- 17 July 2018
- Published by Elsevier in Thermochimica Acta
- Vol. 667, 50-58
Cooling curve thermal analysis and microstructure characterization of Mg-5Zn-1Y-xCa (0–1 wt%) alloys
- 17 July 2018
- Published by Elsevier in Thermochimica Acta
- Vol. 667, 50-58
Cooling curve thermal analysis and microstructure characterization of Mg-5Zn-1Y-xCa (0–1 wt%) alloys
- 8 January 2016
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 124 (2) , 601-609
Effect of cooling rate on the solidification characteristics and dendrite coherency point of ADC12 aluminum die casting alloy using thermal analysis
- 8 January 2016
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 124 (2) , 601-609
Effect of cooling rate on the solidification characteristics and dendrite coherency point of ADC12 aluminum die casting alloy using thermal analysis