Liang Ding
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Liang Ding has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
- Qiang Chen
National University of Defense Technology
4 shared publications - Peiguo Liu
National University of Defense Technology
3 shared publications - Yuejun Zheng
College of Electronic Science and Technology, National University of Defense Technology, Changsha 410073, China
3 shared publications - Yunqi Fu
National University of Defense Technology
3 shared publications - Fang Yuan
Department of Electronic Science, College of Electronic Science and Technology, National University of Defense Technology, Changsha 410073, China
2 shared publications He Jian-Guo
2 shared publications
Latest Publications
- Open Access
- 26 October 2023
- Published by Elsevier in Materials & Design
- Vol. 235
Deterministic approach to decoupling amplitude from phase via a single-layered metasurface
- 26 October 2023
- Published by Elsevier in Materials & Design
- Vol. 235
Open AccessDeterministic approach to decoupling amplitude from phase via a single-layered metasurface
- 9 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 22 (4) , 908-912
W-Band Low-Sidelobe Series-Fed Slot Array Antenna Based on Groove Gap Waveguide
In this letter, a low sidelobe, high efficiency, series-fed 2 24 slot array antenna at 93 GHz is proposed. The antenna can be divided into three separated layers and there is no need of electric contact between layers according to gap waveguide (GW) theory. To control the magnitude of the coupling energy and achieve -30 dB sidelobe quasi-Taylor weighing in radiation slots, transverse coupling slots in the middle layer are placed in a certain distance relative to the bottom gap waveguide center. Measure results agree well with simulation result which demonstrate that the reflection coefficient of the antenna is lower than -10 dB from 91.6 GHz to 94.4 GHz, with over 23 dB gain in the operating band. The 3 dB beamwidth of the E-plane pattern is lower than 4°, while the sidelobe level is lower than -20 dB. The whole antenna's efficiency is higher than 85%.
- 9 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 22 (4) , 908-912
W-Band Low-Sidelobe Series-Fed Slot Array Antenna Based on Groove Gap Waveguide
In this letter, a low sidelobe, high efficiency, series-fed 2 24 slot array antenna at 93 GHz is proposed. The antenna can be divided into three separated layers and there is no need of electric contact between layers according to gap waveguide (GW) theory. To control the magnitude of the coupling energy and achieve -30 dB sidelobe quasi-Taylor weighing in radiation slots, transverse coupling slots in the middle layer are placed in a certain distance relative to the bottom gap waveguide center. Measure results agree well with simulation result which demonstrate that the reflection coefficient of the antenna is lower than -10 dB from 91.6 GHz to 94.4 GHz, with over 23 dB gain in the operating band. The 3 dB beamwidth of the E-plane pattern is lower than 4°, while the sidelobe level is lower than -20 dB. The whole antenna's efficiency is higher than 85%.
- 26 November 2022
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 65 (3) , 810-813
A planar antenna array with wide frequency band and wide end‐fire beam
A planar antenna array with wide frequency band and wide end‐fire radiation beam is proposed in this letter. The antenna element is composed of periodic structure, and its feeding position deviates from the center of symmetry, so end‐fire radiation is obtained. The measurement results show that the antenna array operates in the frequency range of 6.11−10.38 GHz with voltage standing wave ratio less than 2, and the corresponding impedance bandwidth is 51.7%. It exhibits a wide radiation beam of more than 80° at end‐fire direction and achieves realized gain of more than 8 dB in measured band.
- 26 November 2022
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 65 (3) , 810-813
A planar antenna array with wide frequency band and wide end‐fire beam
A planar antenna array with wide frequency band and wide end‐fire radiation beam is proposed in this letter. The antenna element is composed of periodic structure, and its feeding position deviates from the center of symmetry, so end‐fire radiation is obtained. The measurement results show that the antenna array operates in the frequency range of 6.11−10.38 GHz with voltage standing wave ratio less than 2, and the corresponding impedance bandwidth is 51.7%. It exhibits a wide radiation beam of more than 80° at end‐fire direction and achieves realized gain of more than 8 dB in measured band.
- 21 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 22 (2) , 228-232
Ultrabroadband Absorber Based on Layered Inkjet-Printing Resistive Film
This letter proposes an ultrabroadband absorber (UBA) based on the layered inkjet-printing resistive film (IPRF) composed of three lossy layers. The equivalent circuit model of the UBA is put forward to analyze the impedance matching with air under broadband conditions. The prototype was fabricated using IPRF as the lossy layers and the polymethacrylimide (PMI) foam as the dielectric layers. The simulated and measured results show that the ultrabroadband 0 dB absorption performance covers 2–23 GHz with the fractional bandwidth of 168% and maintains stable absorbing performance under the incidence angle of 45°. The total thickness of the proposed design is only 0.1 λL at the lowest operating frequency. Experimental validation of the fabricated prototype has also confirmed the potential using of IPRF-based broadband absorbers in several applications.
- 21 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 22 (2) , 228-232
Ultrabroadband Absorber Based on Layered Inkjet-Printing Resistive Film
This letter proposes an ultrabroadband absorber (UBA) based on the layered inkjet-printing resistive film (IPRF) composed of three lossy layers. The equivalent circuit model of the UBA is put forward to analyze the impedance matching with air under broadband conditions. The prototype was fabricated using IPRF as the lossy layers and the polymethacrylimide (PMI) foam as the dielectric layers. The simulated and measured results show that the ultrabroadband 0 dB absorption performance covers 2–23 GHz with the fractional bandwidth of 168% and maintains stable absorbing performance under the incidence angle of 45°. The total thickness of the proposed design is only 0.1 λL at the lowest operating frequency. Experimental validation of the fabricated prototype has also confirmed the potential using of IPRF-based broadband absorbers in several applications.
- 1 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Systems Engineering and Electronics
- Vol. 32 (3) , 517-526
Integrating electromagnetic surface and antenna array for reflection suppression and excellent radiation
The electromagnetic surface antenna array (EMSAA) has been proposed for obtaining reflection suppression and excellent radiation simultaneously. The antenna with rectangular radiation patch is used to design anisotropic electromagnetic surface. Preternatural reflection characteristics of the element antenna can be tailored depending on the incident polarizations. EMSAA can be constructed by using single structured element antenna with 90° rotation and orthometric arrangement. This or-thometric arrangement of EMSAA is helpful to achieve reflection suppression and excellent radiation. The simulated results show that the reflection of EMSAA is suppressed from 5.0 GHz to 8.0 GHz with peak reduction of 12.3 dB. The linear- and circular-polarized radiation properties of EMSAA are obtained and the maximum gain is 14.3 dBi. The measured results are consistent with the simulation results. The results demonstrate that the reflection suppression and excellent radiation are achieved simultaneously. Such design of EMSAA will open the path for integrating antenna fields and electromagnetic surface (EMS) fields.
- 1 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Systems Engineering and Electronics
- Vol. 32 (3) , 517-526
Integrating electromagnetic surface and antenna array for reflection suppression and excellent radiation
The electromagnetic surface antenna array (EMSAA) has been proposed for obtaining reflection suppression and excellent radiation simultaneously. The antenna with rectangular radiation patch is used to design anisotropic electromagnetic surface. Preternatural reflection characteristics of the element antenna can be tailored depending on the incident polarizations. EMSAA can be constructed by using single structured element antenna with 90° rotation and orthometric arrangement. This or-thometric arrangement of EMSAA is helpful to achieve reflection suppression and excellent radiation. The simulated results show that the reflection of EMSAA is suppressed from 5.0 GHz to 8.0 GHz with peak reduction of 12.3 dB. The linear- and circular-polarized radiation properties of EMSAA are obtained and the maximum gain is 14.3 dBi. The measured results are consistent with the simulation results. The results demonstrate that the reflection suppression and excellent radiation are achieved simultaneously. Such design of EMSAA will open the path for integrating antenna fields and electromagnetic surface (EMS) fields.
- 6 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 69 (11) , 7679-7687
Adaptive High-Impedance Surface for Prevention of Waveguide’s High-Intensity Wave
This article presents an adaptive high-impedance surface (A-HIS) that can be applied in the prevention of high-intensity wave propagating in $X$ -band waveguide. Once the embedded diodes loaded on A-HIS are switched from OFF- to ON-states by the high-intensity incident wave, the boundary condition of the waveguide’s bottom wall would adaptively change from a perfect electric conductor (PEC) to a perfect magnetic conductor (PMC), and the propagation would be prevented. To demonstrate this nonlinear characteristic, eigenmodes of the periodic unit-cells in two states of diodes were calculated, and the dispersive performance was analyzed. The bandwidth was further derived through the bandgaps between its intrinsic modes. Finally, a prototype with $5\times 10$ elements was designed, fabricated, and measured in a WR90 waveguide. The results indicate that, on condition of incident wave with relatively low power intensity, signals can propagate through the A-HIS with a low insertion loss by no more than 1 dB; in the case of relatively high power intensity, this loaded A-HIS can attenuate the incident wave by more than 10 dB and absorb more than 80% power within its operation bandwidth.
- 6 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 69 (11) , 7679-7687
Adaptive High-Impedance Surface for Prevention of Waveguide’s High-Intensity Wave
This article presents an adaptive high-impedance surface (A-HIS) that can be applied in the prevention of high-intensity wave propagating in $X$ -band waveguide. Once the embedded diodes loaded on A-HIS are switched from OFF- to ON-states by the high-intensity incident wave, the boundary condition of the waveguide’s bottom wall would adaptively change from a perfect electric conductor (PEC) to a perfect magnetic conductor (PMC), and the propagation would be prevented. To demonstrate this nonlinear characteristic, eigenmodes of the periodic unit-cells in two states of diodes were calculated, and the dispersive performance was analyzed. The bandwidth was further derived through the bandgaps between its intrinsic modes. Finally, a prototype with $5\times 10$ elements was designed, fabricated, and measured in a WR90 waveguide. The results indicate that, on condition of incident wave with relatively low power intensity, signals can propagate through the A-HIS with a low insertion loss by no more than 1 dB; in the case of relatively high power intensity, this loaded A-HIS can attenuate the incident wave by more than 10 dB and absorb more than 80% power within its operation bandwidth.
- 23 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 69 (8) , 4623-4632
Analysis and Design of a High-Transmittance Performance for Varactor-Tunable Frequency-Selective Surface
This paper aims to achieve a high-transmittance varactor-tunable frequency selective surface (FSS). First, the impedance condition for the high-transmittance FSS is deduced. Next, a square-slot FSS loaded with varactors, owns the empirical formulas for equivalent circuit parameter extraction, is selected to demonstrate the proposed method for realizing a high-transmittance varactor-tunable FSS. Several conclusions are deduced and verified through the full-wave simulation. To illustrate the effectiveness of the proposed method, two FSSs operating at the same frequency are designed. The simulation and measurement results show that the FSS with the higher transmission rate follows the deduced conclusions. Note that the transmission rate of the varactor-tunable FSS is more than 77.8% (S21 = 1.09dB) from 4.84 to 5.9GHz when the bias voltage applied to the varactors is tuned from 5 to 20V. Compared to the reported tunable FSSs, the varactor-tunable FSS achieved in this paper obtains the highest transmission rate over the tunable transmission band.
- 23 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 69 (8) , 4623-4632
Analysis and Design of a High-Transmittance Performance for Varactor-Tunable Frequency-Selective Surface
This paper aims to achieve a high-transmittance varactor-tunable frequency selective surface (FSS). First, the impedance condition for the high-transmittance FSS is deduced. Next, a square-slot FSS loaded with varactors, owns the empirical formulas for equivalent circuit parameter extraction, is selected to demonstrate the proposed method for realizing a high-transmittance varactor-tunable FSS. Several conclusions are deduced and verified through the full-wave simulation. To illustrate the effectiveness of the proposed method, two FSSs operating at the same frequency are designed. The simulation and measurement results show that the FSS with the higher transmission rate follows the deduced conclusions. Note that the transmission rate of the varactor-tunable FSS is more than 77.8% (S21 = 1.09dB) from 4.84 to 5.9GHz when the bias voltage applied to the varactors is tuned from 5 to 20V. Compared to the reported tunable FSSs, the varactor-tunable FSS achieved in this paper obtains the highest transmission rate over the tunable transmission band.
- Open Access
Graphene Based Controllable Broadband Terahertz Metamaterial Absorber with Transmission Band
A graphene-based controllable broadband terahertz metamaterial absorber with transmission band is presented in this paper. It consists of a graphene-SiO2-frequency selective surface (FSS) sandwich structure. The sinusoidal graphene layer supports continuous plasmonic resonances, forming a broad electric-tuning absorbing band. Bandpass FSS constructs a transmission window outside the absorbing band. The simulation results indicate that the absorption from 0.5 THz to 1 THz can be tuned continuously from 0.4 to 0.9 with angle and polarization independence. A transparent window peaking at 1.65 THz maintains high transmittance over 0.7. The metamaterial absorber has potential applications for detection, stealth, filtering, and electromagnetic compatibility.
Open AccessGraphene Based Controllable Broadband Terahertz Metamaterial Absorber with Transmission Band
A graphene-based controllable broadband terahertz metamaterial absorber with transmission band is presented in this paper. It consists of a graphene-SiO2-frequency selective surface (FSS) sandwich structure. The sinusoidal graphene layer supports continuous plasmonic resonances, forming a broad electric-tuning absorbing band. Bandpass FSS constructs a transmission window outside the absorbing band. The simulation results indicate that the absorption from 0.5 THz to 1 THz can be tuned continuously from 0.4 to 0.9 with angle and polarization independence. A transparent window peaking at 1.65 THz maintains high transmittance over 0.7. The metamaterial absorber has potential applications for detection, stealth, filtering, and electromagnetic compatibility.
- 1 February 2014
- Vol. 31 (1) , 29-34
[A detection method of liver iron overload based on static field magnetization principle].
Magnetic induction method aims at the noninvasive detection of liver iron overload by measuring the hepatic magnetic susceptibility. To solve the difficulty that eddy current effects interfere with the measurement of magnetic susceptibility, we proposed an improved coil system based on the static field magnetization principle in this study. We used a direct current excitation to eliminate the eddy current effect, and a rotary receiver coil to get the induced voltage. The magnetic field for a cylindrical object due to the magnetization effect was calculated and the relative change of maximum induced voltage was derived. The correlation between magnetic susceptibility of object and maximum magnetic flux, maximum induced voltage and relative change of maximum induced voltage of the receiver coil were obtained by simulation experiments, and the results were compared with those of the theory calculation. The contrast shows that the simulation results fit the theory results well, which proves our method can eliminate the eddy current effect effectively.
- 1 February 2014
- Vol. 31 (1) , 29-34
[A detection method of liver iron overload based on static field magnetization principle].
Magnetic induction method aims at the noninvasive detection of liver iron overload by measuring the hepatic magnetic susceptibility. To solve the difficulty that eddy current effects interfere with the measurement of magnetic susceptibility, we proposed an improved coil system based on the static field magnetization principle in this study. We used a direct current excitation to eliminate the eddy current effect, and a rotary receiver coil to get the induced voltage. The magnetic field for a cylindrical object due to the magnetization effect was calculated and the relative change of maximum induced voltage was derived. The correlation between magnetic susceptibility of object and maximum magnetic flux, maximum induced voltage and relative change of maximum induced voltage of the receiver coil were obtained by simulation experiments, and the results were compared with those of the theory calculation. The contrast shows that the simulation results fit the theory results well, which proves our method can eliminate the eddy current effect effectively.