Yi Yao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yi Yao has a total of 52 co-authors. Here are the top co-authors by number of shared publications:
Zhengyu Zhang
5 shared publicationsLin Li
4 shared publications- Lin Li
Arizona State University
4 shared publications - Wenjun Cai
Department of Materials Science and Engineering, Virginia Polytechnic Institute and State University, Blacksburg, USA
4 shared publications - Eitan Hershkovitz
Environmental Molecular Sciences Laboratory, Pacific Northwest National Laboratory, Richland, USA
2 shared publications Feng Yan
2 shared publications
Latest Publications
- 28 July 2026
- Published by IOP Publishing in Modelling and Simulation in Materials Science and Engineering
- Vol. 34 (5) , 055024
Hydrogen effects on the generalized stacking fault energy in α -Fe: a comparative atomistic simulation study
Understanding the influence of hydrogen on slip resistance in crystals is essential for elucidating the microscopic mechanisms of hydrogen-enhanced local plasticity and hydrogen embrittlement. As a key physical quantity characterizing slip resistance, the accurate evaluation of the generalized stacking fault energy (GSFE) is of critical importance. However, there is currently no consensus on the appropriate methodology for GSFE calculations in hydrogen-containing systems, leading to significant discrepancies among existing studies. To address this issue, we perform systematic atomistic simulations to calculate the GSFE curves of the slip system in body-centered cubic α -Fe. Different methodological choices in two key steps (i.e. shearing and relaxation) of GSFE calculations are compared. For hydrogen-containing systems, an incremental shear and full relaxation of hydrogen atoms are more reasonable for GSFE calculation. Based on this validated approach, the effect of hydrogen spatial distribution on GSFE is further investigated. The results reveal a pronounced position dependence of GSFE on hydrogen position: hydrogen atoms located at tetrahedral interstitial sites on the slip plane significantly reduce the unstable stacking fault energy, thereby lowering the barriers for slip, whereas hydrogen atoms away from the slip plane may increase slip resistance. Moreover, a complex coupling effect on the GSFE emerges when hydrogen atoms are distributed on and away from the slip plane. This work systematically evaluates GSFE calculation strategies for hydrogen-containing systems and elucidates the position-dependent mechanisms by which hydrogen modulates GSFE, providing a reliable methodological reference for atomistic simulations under hydrogen environments.
- 28 July 2026
- Published by IOP Publishing in Modelling and Simulation in Materials Science and Engineering
- Vol. 34 (5) , 055024
Hydrogen effects on the generalized stacking fault energy in α -Fe: a comparative atomistic simulation study
Understanding the influence of hydrogen on slip resistance in crystals is essential for elucidating the microscopic mechanisms of hydrogen-enhanced local plasticity and hydrogen embrittlement. As a key physical quantity characterizing slip resistance, the accurate evaluation of the generalized stacking fault energy (GSFE) is of critical importance. However, there is currently no consensus on the appropriate methodology for GSFE calculations in hydrogen-containing systems, leading to significant discrepancies among existing studies. To address this issue, we perform systematic atomistic simulations to calculate the GSFE curves of the slip system in body-centered cubic α -Fe. Different methodological choices in two key steps (i.e. shearing and relaxation) of GSFE calculations are compared. For hydrogen-containing systems, an incremental shear and full relaxation of hydrogen atoms are more reasonable for GSFE calculation. Based on this validated approach, the effect of hydrogen spatial distribution on GSFE is further investigated. The results reveal a pronounced position dependence of GSFE on hydrogen position: hydrogen atoms located at tetrahedral interstitial sites on the slip plane significantly reduce the unstable stacking fault energy, thereby lowering the barriers for slip, whereas hydrogen atoms away from the slip plane may increase slip resistance. Moreover, a complex coupling effect on the GSFE emerges when hydrogen atoms are distributed on and away from the slip plane. This work systematically evaluates GSFE calculation strategies for hydrogen-containing systems and elucidates the position-dependent mechanisms by which hydrogen modulates GSFE, providing a reliable methodological reference for atomistic simulations under hydrogen environments.
- Open Access
- 13 May 2026
- Published by Elsevier in SSRN Electronic Journal
Atomistic insight into dislocation behaviors in ultra-lightweight Mg-Li-Al alloys
Mg-Li alloys are among the lightest structural metal materials and exhibit excellent ductility, but their relatively low strength limits broader applications. Alloying, such as with Al, is an effective approach for strengthening Mg-Li alloys. However, the dislocation behavior in BCC Mg-Li alloys remains poorly understood, and the influence of Al addition on such behavior is still unclear. In this study, we first developed a highly accurate machine-learning potential (MLP) for ternary Mg-Li-Al alloys. The developed MLP was subsequently applied to investigate the dislocation behavior of two representative alloys, Mg-38Li and Mg-38Li-4Al (a.t.%). The results show that both alloys exhibit split screw dislocation core structures. Furthermore, Al addition enhances solid-solution strengthening, leading to more jerky edge dislocation motion and consequently lower edge dislocation mobility in Mg-38Li-4Al. Al addition also decreases the screw dislocation velocity, although the reduction is less pronounced than that observed for edge dislocations. And in both alloys, screw dislocation mobility is significantly lower than that of edge dislocations. This reduced mobility is attributed to spontaneous kink-pair nucleation on different planes along the screw dislocation line, which impedes screw dislocation motion. Overall, this study reveals the dislocation behavior in Mg-Li alloys and clarifies the role of Al addition, providing new insight into the design and development of ultra-lightweight Mg-Li alloys.
- 13 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessAtomistic insight into dislocation behaviors in ultra-lightweight Mg-Li-Al alloys
Mg-Li alloys are among the lightest structural metal materials and exhibit excellent ductility, but their relatively low strength limits broader applications. Alloying, such as with Al, is an effective approach for strengthening Mg-Li alloys. However, the dislocation behavior in BCC Mg-Li alloys remains poorly understood, and the influence of Al addition on such behavior is still unclear. In this study, we first developed a highly accurate machine-learning potential (MLP) for ternary Mg-Li-Al alloys. The developed MLP was subsequently applied to investigate the dislocation behavior of two representative alloys, Mg-38Li and Mg-38Li-4Al (a.t.%). The results show that both alloys exhibit split screw dislocation core structures. Furthermore, Al addition enhances solid-solution strengthening, leading to more jerky edge dislocation motion and consequently lower edge dislocation mobility in Mg-38Li-4Al. Al addition also decreases the screw dislocation velocity, although the reduction is less pronounced than that observed for edge dislocations. And in both alloys, screw dislocation mobility is significantly lower than that of edge dislocations. This reduced mobility is attributed to spontaneous kink-pair nucleation on different planes along the screw dislocation line, which impedes screw dislocation motion. Overall, this study reveals the dislocation behavior in Mg-Li alloys and clarifies the role of Al addition, providing new insight into the design and development of ultra-lightweight Mg-Li alloys.
- Open Access
- 20 November 2024
- Published by Springer Nature in Nature Communications
- Vol. 15 (1) , 1-12
Spinel oxide enables high-temperature self-lubrication in superalloys
The ability to lubricate and resist wear at temperatures above 600 °C in an oxidative environment remains a significant challenge for metals due to their high-temperature softening, oxidation, and rapid degradation of traditional solid lubricants. Herein, we demonstrate that high-temperature lubricity can be achieved with coefficients of friction (COF) as low as 0.10-0.32 at 600-900 °C by tailoring surface oxidation in additively-manufactured Inconel superalloy. By integrating high-temperature tribological testing, advanced materials characterization, and computations, we show that the formation of spinel-based oxide layers on superalloy promotes sustained self-lubrication due to their lower shear strength and more negative formation and cohesive energy compared to other surface oxides. A reversible phase transformation between the cubic and tetragonal/monoclinic spinel was driven by stress and temperature during high temperature wear. To span Ni- and Cr-based ternary oxide compositional spaces for which little high-temperature COF data exist, we develop a computational design method to predict the lubricity of oxides, incorporating thermodynamics and density functional theory computations. Our finding demonstrates that spinel oxide can exhibit low COF values at temperatures much higher than conventional solid lubricants with 2D layered or Magnéli structures, suggesting a promising design strategy for self-lubricating high-temperature alloys.
- 20 November 2024
- Published by Springer Nature in Nature Communications
- Vol. 15 (1) , 1-12
Open AccessSpinel oxide enables high-temperature self-lubrication in superalloys
The ability to lubricate and resist wear at temperatures above 600 °C in an oxidative environment remains a significant challenge for metals due to their high-temperature softening, oxidation, and rapid degradation of traditional solid lubricants. Herein, we demonstrate that high-temperature lubricity can be achieved with coefficients of friction (COF) as low as 0.10-0.32 at 600-900 °C by tailoring surface oxidation in additively-manufactured Inconel superalloy. By integrating high-temperature tribological testing, advanced materials characterization, and computations, we show that the formation of spinel-based oxide layers on superalloy promotes sustained self-lubrication due to their lower shear strength and more negative formation and cohesive energy compared to other surface oxides. A reversible phase transformation between the cubic and tetragonal/monoclinic spinel was driven by stress and temperature during high temperature wear. To span Ni- and Cr-based ternary oxide compositional spaces for which little high-temperature COF data exist, we develop a computational design method to predict the lubricity of oxides, incorporating thermodynamics and density functional theory computations. Our finding demonstrates that spinel oxide can exhibit low COF values at temperatures much higher than conventional solid lubricants with 2D layered or Magnéli structures, suggesting a promising design strategy for self-lubricating high-temperature alloys.
- 3 November 2023
- Published by Elsevier in Acta Materialia
- Vol. 263
Selective oxidation and nickel enrichment hinders the repassivation kinetics of multi-principal element alloy surfaces
- 3 November 2023
- Published by Elsevier in Acta Materialia
- Vol. 263
Selective oxidation and nickel enrichment hinders the repassivation kinetics of multi-principal element alloy surfaces
- 29 May 2023
- Published by Elsevier in Acta Materialia
- Vol. 255
Short-range order and its impacts on the BCC MoNbTaW multi-principal element alloy by the machine-learning potential
- 29 May 2023
- Published by Elsevier in Acta Materialia
- Vol. 255
Short-range order and its impacts on the BCC MoNbTaW multi-principal element alloy by the machine-learning potential
- Open Access
- 16 May 2023
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 133 (19)
Atomistic investigations of Cr effect on the deformation mechanisms and mechanical properties of CrCoFeNi alloys
The emerging class of multi-principal element alloy (MPEA) processes superior mechanical properties and has great potential for applications in extreme environments. In this work, the synergic effect of the Cr content and crystallographic orientation on the deformation behaviors of single-crystal CrCoFeNi MPEAs has been investigated by atomistic simulations. We have found distinct differences in dislocation activities, deformation microstructures, and mechanical behaviors in the model MPEAs, which depend on crystallographic orientations, Cr concentration, and the number of activated slip systems. When multiple slip systems are triggered along [100] and [111] orientations, Shockley partial activation and their interaction are predominant, leading to the formation of sessile dislocations and a dense dislocation network. When only two slip systems of Shockley partials are favored along the [110] direction, the influence of Cr concentration and planner defect energies emerges. At low Cr concentration, the double planar slip of Shockley partials results in deformation-induced nanotwins. At high Cr concentration, the partial dislocations of a single slip plane become dominant, attaining the highest volume fraction of deformation-induced phase transformation. The results provide a fundamental understanding of deformation mechanisms in MPEAs, elucidating the synergic effect of crystal orientation and composition on tunning the mechanical behaviors.
- 16 May 2023
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 133 (19)
Open AccessAtomistic investigations of Cr effect on the deformation mechanisms and mechanical properties of CrCoFeNi alloys
The emerging class of multi-principal element alloy (MPEA) processes superior mechanical properties and has great potential for applications in extreme environments. In this work, the synergic effect of the Cr content and crystallographic orientation on the deformation behaviors of single-crystal CrCoFeNi MPEAs has been investigated by atomistic simulations. We have found distinct differences in dislocation activities, deformation microstructures, and mechanical behaviors in the model MPEAs, which depend on crystallographic orientations, Cr concentration, and the number of activated slip systems. When multiple slip systems are triggered along [100] and [111] orientations, Shockley partial activation and their interaction are predominant, leading to the formation of sessile dislocations and a dense dislocation network. When only two slip systems of Shockley partials are favored along the [110] direction, the influence of Cr concentration and planner defect energies emerges. At low Cr concentration, the double planar slip of Shockley partials results in deformation-induced nanotwins. At high Cr concentration, the partial dislocations of a single slip plane become dominant, attaining the highest volume fraction of deformation-induced phase transformation. The results provide a fundamental understanding of deformation mechanisms in MPEAs, elucidating the synergic effect of crystal orientation and composition on tunning the mechanical behaviors.
- Open Access
- 29 December 2022
- Published by Elsevier in Results in Surfaces and Interfaces
- Vol. 10
Processing induced nanoscale heterogeneity impact on the mechanical and electrical behavior of Cu–Zr thin film metallic glasses
- 29 December 2022
- Published by Elsevier in Results in Surfaces and Interfaces
- Vol. 10
Open AccessProcessing induced nanoscale heterogeneity impact on the mechanical and electrical behavior of Cu–Zr thin film metallic glasses
- 1 March 2022
- Published by Elsevier in Scripta Materialia
- Vol. 209
Balancing data for generalizable machine learning to predict glass-forming ability of ternary alloys
- 1 March 2022
- Published by Elsevier in Scripta Materialia
- Vol. 209
Balancing data for generalizable machine learning to predict glass-forming ability of ternary alloys