Yuan Fu
Research Subjects
Yuan Fu has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
Hui Guo
Jiangxi Academy of Sciences
3 shared publicationsJin Liu
Institute of Applied Physics, Jiangxi Academy of Sciences, Nanchang, China
3 shared publicationsLi-Min Xu
Guangdong University of Technology
2 shared publicationsYou Liang Zhang
Institute of Applied Physics, Jiangxi Academy of Sciences Nan Chang China
2 shared publicationsZhi-Yong Wu
JiangXi University of Software Professional Technology
2 shared publicationsAn-An Zhang
Jiangxi Academy of Sciences
1 shared publication
Latest Publications
- 26 May 2025
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 45 (13-14) , 2891-2910
Fracture characterization of woven CFRP laminates-Mode I and III loading
The fracture characteristics of woven carbon fiber reinforced polymer (CFRP) under Mode I and III loading were analyzed. Two tensile testing configurations and experimental methods for simple tests under Mode I and III were employed. The Double Cantilever Beam (DCB) configuration allows for fracture characterization in pure Mode I considering the same specimen arms, using the TDCB model as the specimen’s far-field boundary. Under pure Mode III loading, out-of-plane tension at the end notch was used for fracture characterization. For R curve testing, R curves of Mode I and Mode III Tapered Double Cantilever Beam (TDCB) specimens were obtained with the assistance of infrared sensors and a servo control algorithm. During crack propagation, the stress state in the stress singularity region on crack tip was captured in detail using digital image correlation (DIC) technology. Finally, a mode partitioning method based on Cohesive Zone Model (CZM) was used for the simulation and accuracy prediction of Mode I and III mixed-mode crack propagation. These methods effectively simulated and studied the fracture behavior of composites under complex stress conditions, and provide insights into composite fracture behavior under complex stress, crucial for aerospace and automotive applications where CFRP enhances safety, reliability, and fuel efficiency.
- 26 May 2025
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 45 (13-14) , 2891-2910
Fracture characterization of woven CFRP laminates-Mode I and III loading
The fracture characteristics of woven carbon fiber reinforced polymer (CFRP) under Mode I and III loading were analyzed. Two tensile testing configurations and experimental methods for simple tests under Mode I and III were employed. The Double Cantilever Beam (DCB) configuration allows for fracture characterization in pure Mode I considering the same specimen arms, using the TDCB model as the specimen’s far-field boundary. Under pure Mode III loading, out-of-plane tension at the end notch was used for fracture characterization. For R curve testing, R curves of Mode I and Mode III Tapered Double Cantilever Beam (TDCB) specimens were obtained with the assistance of infrared sensors and a servo control algorithm. During crack propagation, the stress state in the stress singularity region on crack tip was captured in detail using digital image correlation (DIC) technology. Finally, a mode partitioning method based on Cohesive Zone Model (CZM) was used for the simulation and accuracy prediction of Mode I and III mixed-mode crack propagation. These methods effectively simulated and studied the fracture behavior of composites under complex stress conditions, and provide insights into composite fracture behavior under complex stress, crucial for aerospace and automotive applications where CFRP enhances safety, reliability, and fuel efficiency.
- Open Access
- 2 December 2023
- Published by Qeios Ltd
Review of: "Techno-Economic Fermentative Microbe-Based Industrial Production of Lactic Acid (LA): Potential Future Prospects and Constraints"
Dear Author, Thank you for submitting your manuscript titled "Sugar Mills and Second Generation Lactic Acid Production: Challenges and Opportunities". We appreciate your detailed discussion on the advantages and challenges of utilizing second genera...
- 2 December 2023
- Published by Qeios Ltd
Open AccessReview of: "Techno-Economic Fermentative Microbe-Based Industrial Production of Lactic Acid (LA): Potential Future Prospects and Constraints"
Dear Author, Thank you for submitting your manuscript titled "Sugar Mills and Second Generation Lactic Acid Production: Challenges and Opportunities". We appreciate your detailed discussion on the advantages and challenges of utilizing second genera...
- 24 November 2023
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 177, 107929
Mixed modes crack propagation of orthogonal woven-layer in carbon/aramid/epoxy laminates
- 24 November 2023
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 177, 107929
Mixed modes crack propagation of orthogonal woven-layer in carbon/aramid/epoxy laminates
- 11 May 2023
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 36 (12) , 5052-5077
A multiscale homogenization iterative algorithm of 2D orthogonal prepreg carbon/aramid/epoxy woven-ply
An orthogonal mixture woven composites with aramid yarns and carbon yarns are investigated in this work. A dual-scale computational homogenization algorithm is also proposed to address the cross-scale numerical problems. Models and methods for mesoscale and macroscale are illustrated separately. Two types of meso-structures are selected for comparison, which are termed as representative unit cell (RUC) and equivalent cross-ply laminate (ECPL), and the corresponding macro-structures are referred to as RUCs and equivalent cross-ply laminate plain-woven composites (ECPL-PWC). The key finds clarified that the ECPL-PWC takes more computational expenses compared with the RUCs, but the RUCs is in acceptable agreement with testing results, as well as the evaluation results of the ECPL-PWC would obtain very satisfactory accuracy through minor numerical adjustments. The final finite element damage results reveals that the RUCs is more accurate for local damage assessment, while the ECPL-PWC is better for global damage analysis.
- 11 May 2023
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 36 (12) , 5052-5077
A multiscale homogenization iterative algorithm of 2D orthogonal prepreg carbon/aramid/epoxy woven-ply
An orthogonal mixture woven composites with aramid yarns and carbon yarns are investigated in this work. A dual-scale computational homogenization algorithm is also proposed to address the cross-scale numerical problems. Models and methods for mesoscale and macroscale are illustrated separately. Two types of meso-structures are selected for comparison, which are termed as representative unit cell (RUC) and equivalent cross-ply laminate (ECPL), and the corresponding macro-structures are referred to as RUCs and equivalent cross-ply laminate plain-woven composites (ECPL-PWC). The key finds clarified that the ECPL-PWC takes more computational expenses compared with the RUCs, but the RUCs is in acceptable agreement with testing results, as well as the evaluation results of the ECPL-PWC would obtain very satisfactory accuracy through minor numerical adjustments. The final finite element damage results reveals that the RUCs is more accurate for local damage assessment, while the ECPL-PWC is better for global damage analysis.
- 19 March 2022
- Published by Wiley in Polymer Composites
- Vol. 43 (5) , 2651-2671
A dual‐scale homogenization method to study the properties of chopped carbon fiber reinforced epoxy resin matrix composites
In this work, a dual‐scale homogenization (DSH) procedures including the representative volume element (RVE) and Unit cell (UC) with Halpin–Tsai models in the UC scale and space direction‐sensitive Hotelling expansion (SDSHE) models in RVE scale separately. These two methods are introduced and implemented to predict the response of effective elastic properties in chopped fiber reinforced epoxy matrix structures. A post‐processing scheme of subdomain in UC scale based on Gauss theorem is proposed in SDSHE method, which is used to extract the average strain and stress in UC three‐dimensional structure. In addition, the X‐ray computed tomography was used to determine the fourth order tensor orientation angle and the probability distribution information of chopped fiber length in testing samples. Homogenization properties in RVE scale, and inclusion volume fraction (VF), thickness of interface and orientation tensors are designed in UC scale and compared. The excellent correlations with experiments prove the effectiveness of the proposed models. Furthermore, the algorithm proposed in this paper realizes the homogenization of the two scales in the process of numerical analysis, and it will effectively take into account many problems that cannot be achieved by other algorithms, such as the path strain of the model, the thickness of the interface, and so on.
- 19 March 2022
- Published by Wiley in Polymer Composites
- Vol. 43 (5) , 2651-2671
A dual‐scale homogenization method to study the properties of chopped carbon fiber reinforced epoxy resin matrix composites
In this work, a dual‐scale homogenization (DSH) procedures including the representative volume element (RVE) and Unit cell (UC) with Halpin–Tsai models in the UC scale and space direction‐sensitive Hotelling expansion (SDSHE) models in RVE scale separately. These two methods are introduced and implemented to predict the response of effective elastic properties in chopped fiber reinforced epoxy matrix structures. A post‐processing scheme of subdomain in UC scale based on Gauss theorem is proposed in SDSHE method, which is used to extract the average strain and stress in UC three‐dimensional structure. In addition, the X‐ray computed tomography was used to determine the fourth order tensor orientation angle and the probability distribution information of chopped fiber length in testing samples. Homogenization properties in RVE scale, and inclusion volume fraction (VF), thickness of interface and orientation tensors are designed in UC scale and compared. The excellent correlations with experiments prove the effectiveness of the proposed models. Furthermore, the algorithm proposed in this paper realizes the homogenization of the two scales in the process of numerical analysis, and it will effectively take into account many problems that cannot be achieved by other algorithms, such as the path strain of the model, the thickness of the interface, and so on.
- 29 October 2021
- Published by Springer Nature in Applied Composite Materials
- Vol. 29 (2) , 565-595
A Novel Algorithm in Stochastic Chopped Carbon Fiber Composite Structure-A Study of RVE Size Effect and Homogenization Response of Directional Modulus
- 29 October 2021
- Published by Springer Nature in Applied Composite Materials
- Vol. 29 (2) , 565-595
A Novel Algorithm in Stochastic Chopped Carbon Fiber Composite Structure-A Study of RVE Size Effect and Homogenization Response of Directional Modulus