MRMuruganandhan Radhakrishnan

Muruganandhan Radhakrishnan

*This is an algorithmically generated author record based on publicly available information.

Muruganandhan Radhakrishnan has a total of 31 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Surface integrity and corrosion behaviour in AZ91D under multi-pass water jet peening: A process perspective

    by Mugilvalavan Mohan, Amith Sukumaran Chenbagam, Suriyanarayanan Balamurugan, Thirumavalavan Krishnamurthy, Muruganandhan Radhakrishnan, Arunkumar Thirugnanasambandam

    A coupled Eulerian-Lagrangian (CEL) finite element model coupled with the Johnson-Cook constitutive law was developed to model single- and multi-pass water jet peening (WJP) of AZ91D Mg alloy. The model captures the interaction between jet and surface, plastic deformation, and development of surface residual stress at the repeated impact areas. Model predictions were compared with X-ray diffraction measurements and confirmed the good agreement with deviations less than 10%, indicating that it is reliable in predicting subsurface stress fields. The simulations indicate that additional peening passes enhance plastic deformation and compressive residual stress buildup to an optimal condition beyond which stress saturation and partial stress relaxation occur as a result of over-peening. This behaviour is explained by the repetitive removal of surface materials and the redistribution of the highly strained layer. The modelling predictions are corroborated by experimental observations, with the increased micro strain and dislocation density of 0.0024 and 1.25 × 10 15 lines/m 2 , respectively, and the crystallite size also decreased from 50 nm on the unpeened surface to 39 nm after three passes, resulting in an improvement in surface microhardness by 46.4%. Surface topography development to a valley-dominant morphology increases surface energy and wettability, decreasing the contact angle to 73.22 ± 3.53°. The corrosion resistance also improved with an increase in polarisation resistance from 45.92 Ω·cm 2 to 104.83 Ω·cm 2 in 3.5 wt% NaCl. These findings indicate that the controlled multi-pass WJP enhances surface integrity through synergistic effects of strain hardening, crystallite refinement, and compressive residual stress, and over-peening causes surface degradation.

  • Experimental investigations and process optimisation of the submerged waterjet peening process on AZ31B Mg alloy for biomedical applications

    by Mugilvalavan Mohan, Amith S.C., Muruganandhan Radhakrishnan, Thirumavalavan Krishnamurthy, Arunkumar Thirugnanasambandam

    This research investigates the surface treatment of AZ31B magnesium alloy using submerged waterjet peening in order to improve its mechanical properties and biocompatibility for biomedical applications. The experimental parameter conditions were set by varying jet pressure (P) from 100 MPa to 150 MPa and traverse speed (v) from 60 mm/min to 240 mm/min, with a constant standoff distance (h) of 1.5 mm at a single pass. Their effects on surface hardness and roughness were investigated. Results showed that surface roughness increased significantly at lower traverse speeds due to prolonged jet interaction, while hardness improved by up to 26.06% owing to dislocation density and grain refinement. Multi-objective optimisation using the TOPSIS method identified an optimal parameter combination of 150 MPa pressure, 120 mm/min traverse speed, and 1.5 mm standoff distance, balancing roughness and hardness. Validation by Random Forest Regression with Leave One Out Cross Validation ensured model accuracy. Surface morphology exhibited erosion-induced craters and pits because of cavitation-driven plasticity, and XRD analysis confirmed no phase transformation but an increase in dislocation density. Topographical and wettability measurements indicated increased surface energy and decreased contact angle, favoured by greater asperity density. Biocompatibility tests proved enhanced MG-63 cell viability and adhesion on peened surfaces, which verified the bio-functionality of the alloy surface modification. The results establish submerged waterjet peening as a promising, non-thermal surface treatment for AZ31B alloy surface modification for load-bearing implant applications.


  • A study on the effect of various process parameters on low pulsed energy of laser shock peening without ablative layer on the mechanical behavior of AA 7075 T651

    by M Premnath, R Muruganandhan, M Abeens

    Laser shock peening is a well-known surface treatment process that dominates other modern surface treatment processes. Though several materials are investigated to enhance mechanical properties by LSP treatment, only a scarce number of studies have concentrated on Low Pulsed Laser Shock Peening (LPLSP) without an ablative layer on Aluminum Alloy 7075 T651 material. Thus this article investigates the optimization and effect of LPLSP on the mechanical behavior of AA 7075 T651. Grey Relational Analysis is chosen to optimize the Process Parameters on Low Pulsed Energy of LSP. The significant contributions of the optimized parameters on the mechanical behavior such as hardness, compressive residual stress, roughness and friction wear property are investigated. A drastic improvementof three times in the average hardness value occurred in LPLSP over the un-peened specimen. A maximum compressive residual stress is observed with the LPLSP specimen for the optimized parameters. An improvement of 65% in the minimum wear rate was recorded in LPLSP compared to unpeened specimens. The microstructural studies carried outusing an optical microscope and scanning electron microscope show a typical grain refinement and increase in the boundary for LPLSP specimen.


  • Open Access

    Influence of Graphene Nano Fillers and Carbon Nano Tubes on the Mechanical and Thermal Properties of Hollow Glass Microsphere Epoxy Composites

    by Kumar D, Kiran Shahapurkar, C. Venkatesh, Muruganandhan R, Vineet Tirth, Chandru Manivannan, Ibrahim M. Alarifi, Manzoore Elahi M. Soudagar, Ahmed S. El-Shafay

    The present work aimed to analyze the roll of carbon nano tubes and graphene nano fillers on the mechanical and thermal characteristics of hollow glass microsphere reinforced epoxy composites. Composites with varying content of hollow glass microballoons (2, 4, 6, 8, and 10 wt %) reinforced in epoxy matrix were fabricated. Additionally, two more types of composites, one with graphene nano fillers and the other with carbon nano tube at a constant 0.5 wt %, were fabricated with varying weight percentages of hollow glass microballoons (2, 4, 6, 8, and 10%). The composites were fabricated using an open mold casting process. Composites were tested for thermal and mechanical properties. The tensile and flexural moduli were found to rise as the HGM concentration increased. Graphene-filled HGM/epoxy composites revealed the highest modulus compared with HGM/epoxy and HGM/CNT/epoxy composites. The impact strength of all composite types decreased as the HGM content increased. Neat epoxy specimens revealed low response as compared with all the composites tested. Further, the thermal conductivity of HGM/epoxy composites was lower as compared with other compositions and neat epoxy. Scanning electron microscopy was used to analyze the surface morphological behavior of the composites subjected to flexural test. It was found that HGM/G/E composites with 10% of HGM and 0.5% of graphene by weight in epoxy matrix were the optimum.


  • Investigation of corrosion behavior on plastically deformed aa 7075 t651 by shot peening process

    by Abeens M, R Muruganandhan

    As AA 7075 T651 comprehensively is used in the marine naval vessels, the factor of corrosion performance always plays a significant role. In this work, an investigation is carried out to study the effect of corrosion behavior of shot peened AA 7075 T651 in 3.5% solution. From the potentio-dynamic polarization study, a 27.72% decrease is ascertained in the I corr in shot peened specimen in correlation to unpeened aluminium alloy. A drop in I corr from 1.883 to 1.480 mA cm −2 in shot peened specimen, indicates enhanced pitting corrosion resistance. An electrochemical impedance spectroscopy reveals a surge in the oxide layer formation on the peened surface aiding the drop in corrosion rate. Resistance to pit formations and improvement in oxygen deposition in the peened specimen is observed availing a Scanning Electron Microscopy (SEM) and Energy Dispersive x-ray analysis (EDX). The micro structures of the peened and unpeened specimen are captured using optical microscopy and Transmission electron microscopy (TEM). Micro-strain, dislocation density is also calculated from the x-ray diffraction analysis (XRD), in which grain size reduces by 28.07%, dislocation density surges by 38.65% and micro strain increases by 21.95% in peened specimen in correlation to unpeened AA 7075 T651. As a result of these improvements the corrosion resistance by 27.92% in the peened specimen in correlation to unpeened aluminium alloy.


  • Open Access

    Investigations on Water Jet Peening of AZ31B Mg Alloy for Bio Medical Implants

    by Mugilvalavan Mohan, Muruganandhan Radhakrishnan, Yuvaraj Natarajan

    Among different unconventional peening technique, water jet is cold working process has capable to produce surface topography on wide variety of materials. This paper deals with the effect of water jet peening on the corrosion resistance and the surface topography of AZ31B Mg alloy. Variations in water jet peening variables including standoff distance, traverse speed and multiple passes have been employed in this study. A study of the enhancement in hardening and roughening effect was made following the peening process. 29.44% Improvements in microhardness and 31.06% reduction in surface roughness were observed on the peened surfaces. Optimal peened surface was obtained through use of the multi-objective optimization technique, namely, TOPSIS, which utilizes response variables such as micro hardness and surface roughness. In this study, Surface Topography, XRD Analysis and Electrochemical test were conducted. In addition, analysis of the Microstructure of corroded region was made in the unpeened and optimized peened surfaces. Surface topography parameters including Sa, Sq, SSk, Sku results confirmed the suitability of the peened surface for ooseointegration and cell growth. FWHM value measured from XRD peaks showed the formation of grain refinement on the peened surface, and the results showed promising improvements in the corrosion resistance compared to the unpeened AZ31B Mg alloy.


  • CFD simulation of convective heat transfer in vessel with mechanical agitation for milk

    by E. Rajasekaran, B. Kumar, R. Muruganandhan, S. V. Raman, G. Nandhini Devi

    Computational fluid dynamics (CFD) analysis using ANSYS Fluent software has been carried out to investigate velocity profiles and thermal characteristics of milk during heating under mechanically agitated condition. In earlier article experimental data on forced convection heat transfer coefficient \(\left(\stackrel{-}{\mathrm{h}}\right)\) and correlations of the form \(\mathrm{N}\mathrm{u}=\mathrm{a}\cdot {\mathrm{R}\mathrm{e}}^{\mathrm{b}}\cdot {\mathrm{P}\mathrm{r}}^{0.33}\) for cow milk, standardised milk and full cream milk in Baffled vessel and Unbaffled vessel with scraping, using Propeller, Flat Six Blade Turbine (FBT), Inclined Six Blade Turbine (IBT) and Paddle impellers were reported. It was noted milk in Baffled vessel with Paddle impeller provided highest \(\stackrel{-}{\mathrm{h}}\) even at lower rotational speeds followed by Propeller, FBT and IBT impellers. In Unbaffled vessel with scraping, Propeller provided the highest \(\stackrel{-}{\mathrm{h}}\) followed by FBT and IBT impellers. Hence, the present investigation has been carried out to validate and understand how different velocity of flow currents and their magnitude influence the heat transfer coefficient values in CFD simulation. It also justifies the relative performance of the impellers delineated in the earlier paper. In addition, theoretical values of heat transfer coefficients computed using CFD shows close agreement with experimental values.


  • Influence of amine-functionalised graphene oxide filler on mechanical and insulating property of epoxy nanocomposites

    by T Manikandan, Arjunan Siddharthan, R Muruganandhan, C Pugazhendhi Sugumaran

    Graphene oxide incorporated epoxy nanocomposites were prepared using synthesised graphene oxide (GO) and amine functionalised graphene oxide (AGO) in various loading (0 - 0.6) wt. % by solution blending method. As synthesised GO and AGO were characterised by Fourier transform infrared spectrum (FTIR), X-ray diffraction (XRD) and Thermogravimetric (TG) analysis. The dielectric permittivity and loss factor of GO/AGO epoxy nanocomposites were found out by impedance analyser in the frequency range of 101 to 106 Hz. The dielectric endurance of GO/AGO epoxy nanocomposites was investigated by dielectric breakdown strength and electrical resistivity. It was found that for filler loadings up to 0.4 wt. % of both GO and AGO, there was a proportionate change in properties due to homogeneous dispersion. The study shows surface functionalised AGO-epoxy nanocomposites have shown better permittivity, loss factor, and breakdown strength than neat epoxy and GO-epoxy composites.


  • Determination of forced convection heat transfer coefficients and development of empirical correlations for milk in vessel with mechanical agitators

    by E. Rajasekaran, B. Kumar, R. Muruganandhan, S. V. Raman, Usha Antony

    Heating of milk is an important unit operation to produce many milk based products. This process is done either in heat exchangers or in agitated vessels, where the mode and type of heat transfer plays a significant role. Use of mechanical agitator with suitable impeller would result in uniform agitation of the liquid. Data for forced convection heat transfer coefficients for milk in agitated vessel have not been documented. In the present investigation, forced convection heat transfer coefficients for milk, using mechanical agitators in vessels have been determined. Experiments have been conducted in vessels (Baffled as well as Unbaffled vessel) that were designed and fabricated under standard procedure employing: (1) Flat Six Blade Turbine impeller, (2) Inclined Six Blade Turbine impeller, (3) Three Blade Propeller impeller and (4) Two Bladed Paddle. Heat transfer coefficients were determined for \( \left( {\overline{\text{h}} } \right) \) for cow milk (3.5% fat), standardised milk (4.5% fat) and full cream milk (6.0% fat). The Two Bladed Paddle was found to as yield the highest heat transfer coefficient \( \left( {\overline{\text{h}} } \right) \) for all three types of milk. In addition, empirical correlations for the forced convection heat transfer using \( {\text{Nu}} = {\text{a}} \cdot {\text{Re}}^{\text{b}} \cdot { \Pr }^{0.33} \) have been developed for each case. These heat transfer correlations derived will find application in large scale design and the experimental setup would be useful for future investigation with different liquids and impellers.