Tunde Isaiah Toluwaloju
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Tunde Isaiah Toluwaloju has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Dunant Halim
University of Nottingham, Ningbo - University of Nottingham Ningbo China
6 shared publicationsChung Ket Thein
University of Nottingham, Ningbo - University of Nottingham Ningbo China
5 shared publications- Chung Ket Thein
University of Nottingham Ningbo China
5 shared publications - Dunant Halim
Nottingham Ningbo China Beacons of Excellence Research and Innovation Institute, University of Nottingham Ningbo China, Ningbo, China
2 shared publications Abimbola Chris Ogunyele
1 shared publication- Adedapo Oluwasanu Adeola
Department of Chemistry and Biochemistry and the Centre for NanoScience Research, Concordia University, Montreal, QC, H4B 1R6, Canada; Quebec Centre for Advanced Materials, Department of Chemistry and Biochemistry, Concordia University, Montreal, QC, H4B 1R6, Canada
1 shared publication
Latest Publications
- Open Access
- 20 October 2026
- Published by Springer Nature in Discover Mechanical Engineering
- Vol. 5 (1) , 201
Controlled intermittent non smoothed contact induced antiphase dynamics for broadband electromagnetic vibration energy harvesting
- 20 October 2026
- Published by Springer Nature in Discover Mechanical Engineering
- Vol. 5 (1) , 201
Open AccessControlled intermittent non smoothed contact induced antiphase dynamics for broadband electromagnetic vibration energy harvesting
- Open Access
- 25 November 2024
- Published by MDPI AG in Engineering Proceedings
- Vol. 82 (1) , 105
Enhancing Voltage and Power Output Through the Structural Optimization of Coil–Magnet Transducers in Electromagnetic Vibration Energy Harvesters
Electromagnetic vibration energy harvesters (EVEHs) have emerged as a promising approach to powering small electronic devices and sensors, particularly in remote or inaccessible locations where traditional power sources are impractical. This study investigates approaches for structurally scaling and optimizing the EVEH transducer magnet structure to maximize the magnet flux density, total flux density, harvested voltages and power output. Six design configurations have been analyzed in different coils and transducer magnet/flux guiding steel geometries. While the coil varies by using bulk or split coils, the magnet/flux guiding steel is varied by using different sizes. Analytical validation and simulations showed that these variations generally affected the transducer flux density per unit magnet volume and total volume . Validation shows that configurations with a split center magnet with the smallest transducer volume attains preferable and power density by approximately 21.66%, 15.77% and 54.47% over the reference model without center magnet/steel. Therefore, the most structurally optimized configuration attained a light weight but a higher energy conversion/flux coupling efficiency. Also, the analysis showed that using split slotted coils is more efficient for energy harvesting than using bulk equivalent (single) coils counterparts. This is because the split coil will encourage more flux coupling than bulk coil. Additionally, the optimal load capacity is considerably reduced by approximately 50.00% on configurations with split coil. Therefore, split and bulk are respectively suitable for low- and high-impedance matching.- 25 November 2024
- Published by MDPI AG in Engineering Proceedings
- Vol. 82 (1) , 105
Open AccessEnhancing Voltage and Power Output Through the Structural Optimization of Coil–Magnet Transducers in Electromagnetic Vibration Energy Harvesters
Electromagnetic vibration energy harvesters (EVEHs) have emerged as a promising approach to powering small electronic devices and sensors, particularly in remote or inaccessible locations where traditional power sources are impractical. This study investigates approaches for structurally scaling and optimizing the EVEH transducer magnet structure to maximize the magnet flux density, total flux density, harvested voltages and power output. Six design configurations have been analyzed in different coils and transducer magnet/flux guiding steel geometries. While the coil varies by using bulk or split coils, the magnet/flux guiding steel is varied by using different sizes. Analytical validation and simulations showed that these variations generally affected the transducer flux density per unit magnet volume and total volume . Validation shows that configurations with a split center magnet with the smallest transducer volume attains preferable and power density by approximately 21.66%, 15.77% and 54.47% over the reference model without center magnet/steel. Therefore, the most structurally optimized configuration attained a light weight but a higher energy conversion/flux coupling efficiency. Also, the analysis showed that using split slotted coils is more efficient for energy harvesting than using bulk equivalent (single) coils counterparts. This is because the split coil will encourage more flux coupling than bulk coil. Additionally, the optimal load capacity is considerably reduced by approximately 50.00% on configurations with split coil. Therefore, split and bulk are respectively suitable for low- and high-impedance matching. - Open Access
- 20 September 2023
- Published by Elsevier in SSRN Electronic Journal
Vibration Isolation or Amplification on a Levered-Coulomb Damped System by Alteration the Potential Energy Barrier
This work considers levered dual response, Coulomb damped mechanism for realizing vibration isolation and taking advantage of the friction in the guiderails/bearing to initiate a change in the potential well realized in three designs, i.e., strategies A (with both horizontal and vertical guiderails), B (with horizontal rail), and C (no guiderails). Varying potential well was realized as consequence of different friction by using varying number of sliders and bearing. Potential energy curve indicated a transition from bi-stable to mono-stable and then unstable on strategies A, B, and C. Theoretical model and the corresponding governing equation was obtained using the Lagrange energy method to 92.34% accuracy between experiment and analytical solution. While A, B, and C demonstrated capacities for consistent operation in a large excitation, the potential distribution on strategy C registered a dominant deeper potential well over strategies B and A while A only realizes pseudo stability at resonant. The implication of the deeper potential well as a result of lesser friction in strategy C is that the band of transition zone from stick slip to continuous or vice versa is larger than those registered on strategies A and B such that at sufficiently higher excitation, the response in strategy C may grow into being stochastic while those on A and B is still harmonics of excitation. Generally, the region of isolation on the transmissibility profile are points of stability while amplification points are not stable. Analytical solution showed strategy C realized profound isolation in the region of deeper well, hence, Coulomb frictional force in the mechanical system frictional realized as one effective approach to alter the potential energy barrier thus enhancing/eliminating isolation in a mechanical system by a controlled introduction to effectively broaden/enhance the isolation band/depth respectively. Most isolators attained isolation at [[EQUATION]]; [[EQUATION]] is the resonant frequency, the response-potential curves for model under consideration showed that isolation is attained at [[EQUATION]][[EQUATION]] and [[EQUATION]] in strategies A, B and C respectively. The above suggests that shallow potential barrier is beneficial for a broadband isolation as shown in strategy B while intrawell oscillations as shown in strategy C is beneficial for isolation.
- 20 September 2023
- Published by Elsevier in SSRN Electronic Journal
Open AccessVibration Isolation or Amplification on a Levered-Coulomb Damped System by Alteration the Potential Energy Barrier
This work considers levered dual response, Coulomb damped mechanism for realizing vibration isolation and taking advantage of the friction in the guiderails/bearing to initiate a change in the potential well realized in three designs, i.e., strategies A (with both horizontal and vertical guiderails), B (with horizontal rail), and C (no guiderails). Varying potential well was realized as consequence of different friction by using varying number of sliders and bearing. Potential energy curve indicated a transition from bi-stable to mono-stable and then unstable on strategies A, B, and C. Theoretical model and the corresponding governing equation was obtained using the Lagrange energy method to 92.34% accuracy between experiment and analytical solution. While A, B, and C demonstrated capacities for consistent operation in a large excitation, the potential distribution on strategy C registered a dominant deeper potential well over strategies B and A while A only realizes pseudo stability at resonant. The implication of the deeper potential well as a result of lesser friction in strategy C is that the band of transition zone from stick slip to continuous or vice versa is larger than those registered on strategies A and B such that at sufficiently higher excitation, the response in strategy C may grow into being stochastic while those on A and B is still harmonics of excitation. Generally, the region of isolation on the transmissibility profile are points of stability while amplification points are not stable. Analytical solution showed strategy C realized profound isolation in the region of deeper well, hence, Coulomb frictional force in the mechanical system frictional realized as one effective approach to alter the potential energy barrier thus enhancing/eliminating isolation in a mechanical system by a controlled introduction to effectively broaden/enhance the isolation band/depth respectively. Most isolators attained isolation at [[EQUATION]]; [[EQUATION]] is the resonant frequency, the response-potential curves for model under consideration showed that isolation is attained at [[EQUATION]][[EQUATION]] and [[EQUATION]] in strategies A, B and C respectively. The above suggests that shallow potential barrier is beneficial for a broadband isolation as shown in strategy B while intrawell oscillations as shown in strategy C is beneficial for isolation.
- 19 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Flux feedback mechanism for realizing enhanced flux density in an electromagnetic vibration energy harvester
This work focus on improving the efficiency of the transducer that could harvest and convert ambient vibration into electrical energy by using a coupled coil-magnet transducer model. During vibration, the electrical energy is induced in the coil by electromagnetic induction, such energy could successfully power sensor nodes and micro devices. Since the degree of the flux filed of the permanent magnet determined the extent of coupling and the voltage/power induced in the coil during vibration, this work focus on how to realize an improved flux field in the coil using a flux feedback mechanism in the magnet geometry. While noting that the flux density in the model without feedback increase by approximate 4.00 % for every 0.50 mm increase in the thickness of the flux converging steel, the model with feedback shows that for equivalent increase in the feedback thickness, a higher flux density is measure at the center coil slot position, however, the flux depleted with increasing feedback thickness at the sided coil slot position on the model with feedback. If the slotted coils are connected in series over equivalent R l , when zero flux leakage is realized in both conventional and flux feedback model, the harvested power on the feedback model improved by 57.36 % and 9.94 % at = w s‒con = 0.20, w s = 1.00 mm and w s = 2.00 mm respectively relative to conventional model at w s‒con = 0.00 mm and w s = 5.00 mm.
- 19 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Flux feedback mechanism for realizing enhanced flux density in an electromagnetic vibration energy harvester
This work focus on improving the efficiency of the transducer that could harvest and convert ambient vibration into electrical energy by using a coupled coil-magnet transducer model. During vibration, the electrical energy is induced in the coil by electromagnetic induction, such energy could successfully power sensor nodes and micro devices. Since the degree of the flux filed of the permanent magnet determined the extent of coupling and the voltage/power induced in the coil during vibration, this work focus on how to realize an improved flux field in the coil using a flux feedback mechanism in the magnet geometry. While noting that the flux density in the model without feedback increase by approximate 4.00 % for every 0.50 mm increase in the thickness of the flux converging steel, the model with feedback shows that for equivalent increase in the feedback thickness, a higher flux density is measure at the center coil slot position, however, the flux depleted with increasing feedback thickness at the sided coil slot position on the model with feedback. If the slotted coils are connected in series over equivalent R l , when zero flux leakage is realized in both conventional and flux feedback model, the harvested power on the feedback model improved by 57.36 % and 9.94 % at = w s‒con = 0.20, w s = 1.00 mm and w s = 2.00 mm respectively relative to conventional model at w s‒con = 0.00 mm and w s = 5.00 mm.
- 16 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
A Parametric Analysis on Performance Dependence of Electromagnetic Vibration Harvester on the Coil Position, Coil Connection, and Magnetic Flux Density
This paper presented a simulation approach to curate methods for determining which coil geometry/connection type, however of equal volume is most suitable for achieving higher power output of an electromagnetic harvester by positionally maximizing the magnetic flux density cutting across the transduction coil in different coil connection modes. The average magnetic flux density of the magnet at the coil positions were simulated by Finite Element Method Magnetics (FEMM) software and the predicted voltage/power were computed and the connection type that is most suitable over equal coil volume for realizing highest harvestable power was determined. The magnetic flux through six different coils were simulated and reported using different coil dimensions and positions. The power harvested over each design are compared and conclusions are drawn as to which design strategies is suitable for energy harvesting over equal coil volume. Most general among conclusions reached in this work is that using two side positioned 4mm width coil geometry, the magnetic flux cutting across each of the transduction coil is increased by about 9.37% compared to an equal volume 8 mm center positioned coil, while the harvested power increased by 14.45 % when the 8 mm center positioned coil is change to parallel connected split 4 mm coils hence, we conclude that irrespective of the connection type, using side positioned coil show prospect for enhanced performance over a single, equal volume center positioned coil while the parallel connected coils significantly performs better than the series connected counterparts.
- 16 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
A Parametric Analysis on Performance Dependence of Electromagnetic Vibration Harvester on the Coil Position, Coil Connection, and Magnetic Flux Density
This paper presented a simulation approach to curate methods for determining which coil geometry/connection type, however of equal volume is most suitable for achieving higher power output of an electromagnetic harvester by positionally maximizing the magnetic flux density cutting across the transduction coil in different coil connection modes. The average magnetic flux density of the magnet at the coil positions were simulated by Finite Element Method Magnetics (FEMM) software and the predicted voltage/power were computed and the connection type that is most suitable over equal coil volume for realizing highest harvestable power was determined. The magnetic flux through six different coils were simulated and reported using different coil dimensions and positions. The power harvested over each design are compared and conclusions are drawn as to which design strategies is suitable for energy harvesting over equal coil volume. Most general among conclusions reached in this work is that using two side positioned 4mm width coil geometry, the magnetic flux cutting across each of the transduction coil is increased by about 9.37% compared to an equal volume 8 mm center positioned coil, while the harvested power increased by 14.45 % when the 8 mm center positioned coil is change to parallel connected split 4 mm coils hence, we conclude that irrespective of the connection type, using side positioned coil show prospect for enhanced performance over a single, equal volume center positioned coil while the parallel connected coils significantly performs better than the series connected counterparts.
- Open Access
- 1 November 2022
- Published by MDPI AG in Engineering Proceedings
- Vol. 27 (1) , 58
Finite Element Simulation for Predicting the Magnetic Flux Density for Electromagnetic Vibration Energy Harvester
The current revolution in the field of electromagnetic vibration energy harvester requires that both wireless sensor nodes and relevant power sources be cost- and size-optimized while ensuring that, during design/fabrication of the sensor’s power sources, the power deliverable to the sensors be maximum. Flux density dependency on the nature of the magnetic coupling material of VEH magnet-coil transducer is well reported while reports on size-optimized but improved performance in the VEH is available. This paper presents on the realization of an approach to ensure an accurate prediction of size-optimized but maximum power output on the electromagnetic transducer of a VEH. The adopted approach justifiably verifies the geometrically determined flux density on a Finite Element Magnetic Method Software (FEMM) on the permanent magnet (NdFeB N52) as a basis for optimization. An empirical formula—which predicts size-optimized flux density and could be used to predict the performance of a miniature energy harvester for wireless sensor nodes application—was formulated. For the geometry presented in this work, where and are the effective length and turns on the reference coil, the magnetic flux density, coupling coefficients, coil width and transducer thickness were predicted to optimize at 0.4373 T, 0.3978 Tmm, 4.00 mm and 18.40 mm, respectively, with all corresponding to instances when the flux density per unit volume on the coil was approximately 0.4373T. The above optimized values were measured on magnet-coil geometry with the smallest overall thickness. However, in comparison to other models, the coil thickness in the optimized geometry was not the least.- 1 November 2022
- Published by MDPI AG in Engineering Proceedings
- Vol. 27 (1) , 58
Open AccessFinite Element Simulation for Predicting the Magnetic Flux Density for Electromagnetic Vibration Energy Harvester
The current revolution in the field of electromagnetic vibration energy harvester requires that both wireless sensor nodes and relevant power sources be cost- and size-optimized while ensuring that, during design/fabrication of the sensor’s power sources, the power deliverable to the sensors be maximum. Flux density dependency on the nature of the magnetic coupling material of VEH magnet-coil transducer is well reported while reports on size-optimized but improved performance in the VEH is available. This paper presents on the realization of an approach to ensure an accurate prediction of size-optimized but maximum power output on the electromagnetic transducer of a VEH. The adopted approach justifiably verifies the geometrically determined flux density on a Finite Element Magnetic Method Software (FEMM) on the permanent magnet (NdFeB N52) as a basis for optimization. An empirical formula—which predicts size-optimized flux density and could be used to predict the performance of a miniature energy harvester for wireless sensor nodes application—was formulated. For the geometry presented in this work, where and are the effective length and turns on the reference coil, the magnetic flux density, coupling coefficients, coil width and transducer thickness were predicted to optimize at 0.4373 T, 0.3978 Tmm, 4.00 mm and 18.40 mm, respectively, with all corresponding to instances when the flux density per unit volume on the coil was approximately 0.4373T. The above optimized values were measured on magnet-coil geometry with the smallest overall thickness. However, in comparison to other models, the coil thickness in the optimized geometry was not the least. - 22 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Investigation on the Effect of Magnetic Coupling and Power Harvested in an Electromagnetic Vibration Energy Harvester
An approach to ensure an increased power output on a resonant energy harvester through the magnetic flux/coupling between the magnets and transduction coil design was presented in this work. The power harvested on an electromagnetic energy harvester not only depends on the structural component but also relies on the electrical/coupling parameters. The flux/coupling variation reported in this work was achieved by using either air, steel, magnets, or a hybrid of air-iron-magnet design between the outer magnet space. The coupling/flux variation design was investigated using seven different models while the effective magnetic flux density on each different model was computed using the Finite Element Magnetic Methods (FEMM) software. The work reported here shows that using iron as the coupling material raised the flux density and power harvested by 8.37% and 1.76 % respectively compared to air. Also, using magnets as the coupling material increased the flux density and power harvested by 25.06 % and 3.99 %, respectively. In addition, the power per center magnet and iron volume was obtained at 1.21 $\mathrm{W}\mathrm{m}^{-3}$ and 1.18 $\mathrm{W}\mathrm{m}^{-3}$, respectively. It was concluded that using magnet as the center coupling material will result in a higher level of harvestable power for any electromagnetic harvester design geometry.- 22 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Investigation on the Effect of Magnetic Coupling and Power Harvested in an Electromagnetic Vibration Energy Harvester
An approach to ensure an increased power output on a resonant energy harvester through the magnetic flux/coupling between the magnets and transduction coil design was presented in this work. The power harvested on an electromagnetic energy harvester not only depends on the structural component but also relies on the electrical/coupling parameters. The flux/coupling variation reported in this work was achieved by using either air, steel, magnets, or a hybrid of air-iron-magnet design between the outer magnet space. The coupling/flux variation design was investigated using seven different models while the effective magnetic flux density on each different model was computed using the Finite Element Magnetic Methods (FEMM) software. The work reported here shows that using iron as the coupling material raised the flux density and power harvested by 8.37% and 1.76 % respectively compared to air. Also, using magnets as the coupling material increased the flux density and power harvested by 25.06 % and 3.99 %, respectively. In addition, the power per center magnet and iron volume was obtained at 1.21 $\mathrm{W}\mathrm{m}^{-3}$ and 1.18 $\mathrm{W}\mathrm{m}^{-3}$, respectively. It was concluded that using magnet as the center coupling material will result in a higher level of harvestable power for any electromagnetic harvester design geometry.- Open Access
- 1 November 2021
- Published by MDPI AG in Engineering Proceedings
- Vol. 10 (1) , 5
An Effect of Coupling Factor on the Power Output for Electromagnetic Vibration Energy Harvester
Sensors are devices that measures a change in physical stimulus by converting it into an electronic signal which can be read by a designated instrument. To overcome the real-life challenges associated with powering a sensor using conventional batteries and chargers, this work focuses on formulating analytical framework for designing an ecofriendly, cheap, almost zero retrofit implication (except on damage) power module for sensors using an electromagnetic vibration energy harvester. This principle relies on the electromagnetic transduction whose harvested voltage/power is formulated from Faraday law of electromagnetic induction. An electromagnetic parameter that determines the degree of transduction is the coupling constant. The value of coupling constant must be accurately set during harvester design because it directly determines harvester damping ratio and the power available for the sensor. All parameters used to compute the coupling except the flux density are constant. In this work, we focus on formulating a set of analytical equations that could effectively determine the harvester’s optimum magnetic flux parameter to be used in computing the optimum coupling constant, the electromagnetic damping ratio, and the harvested power at resonant. This work concludes that the degree of coupling for the determined optimum flux density increases with an increased load resistance and hence larger harvested power is available to power the sensor.
- 1 November 2021
- Published by MDPI AG in Engineering Proceedings
- Vol. 10 (1) , 5
Open AccessAn Effect of Coupling Factor on the Power Output for Electromagnetic Vibration Energy Harvester
Sensors are devices that measures a change in physical stimulus by converting it into an electronic signal which can be read by a designated instrument. To overcome the real-life challenges associated with powering a sensor using conventional batteries and chargers, this work focuses on formulating analytical framework for designing an ecofriendly, cheap, almost zero retrofit implication (except on damage) power module for sensors using an electromagnetic vibration energy harvester. This principle relies on the electromagnetic transduction whose harvested voltage/power is formulated from Faraday law of electromagnetic induction. An electromagnetic parameter that determines the degree of transduction is the coupling constant. The value of coupling constant must be accurately set during harvester design because it directly determines harvester damping ratio and the power available for the sensor. All parameters used to compute the coupling except the flux density are constant. In this work, we focus on formulating a set of analytical equations that could effectively determine the harvester’s optimum magnetic flux parameter to be used in computing the optimum coupling constant, the electromagnetic damping ratio, and the harvested power at resonant. This work concludes that the degree of coupling for the determined optimum flux density increases with an increased load resistance and hence larger harvested power is available to power the sensor.