Dong Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dong Zhang has a total of 70 co-authors. Here are the top co-authors by number of shared publications:
- Xiao Gong
National University of Singapore
26 shared publications - Chen Sun
Department of Electrical and Computer Engineering, National University of Singapore, Queenstown, Singapore
19 shared publications - Xiaolin Wang
Department of Electrical and Computer Engineering, National University of Singapore, Queenstown, Singapore
19 shared publications - Gan Liu
National University of Singapore (NUS)
17 shared publications - Leming Jiao
Department of Electrical and Computer Engineering, National University of Singapore, Queenstown, Singapore
14 shared publications - Qiwen Kong
Department of Electrical and Computer Engineering, National University of Singapore, Queenstown, Singapore
13 shared publications
Latest Publications
- 5 October 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (14)
Overcoming the mobility–reliability trade-off in BEOL-compatible In2O3-based FETs through synergistic doping and prolonged annealing
Oxide semiconductors field-effect transistors (OS FETs) capable of simultaneously delivering high mobility and excellent reliability are a key platform for high-performance circuits and memory modules in monolithic three-dimensional integrated circuits (M3D ICs). In this work, we propose a synergistic strategy combining Zn doping and prolonged thermal annealing (PTA) to address the mobility–reliability trade-off in InZnOX FETs. The Zn doping ratio was controlled by adjusting the precursor-cycle ratio during atomic layer deposition. Zn incorporation suppresses channel crystallization during PTA, allowing the InZnOX channel to retain its amorphous structure. The results indicate that Zn doping effectively suppresses the hydrogen-related negative threshold-voltage shift (ΔVTH) and improves device reliability, while PTA mitigates the mobility degradation induced by doping and further enhances bias-stress stability. In particular, all PTA-treated InZnOX FETs exhibit mobilities exceeding 80 cm2 V−1 s−1, outperforming the InZnOX FETs without PTA. For PTA-treated devices with an In:Zn ratio of 22:1, a |ΔVTH| of only 11 mV after 1000 s of stress is achieved at 360 K under a gate-overdrive voltage of 4 V. These results demonstrate a feasible approach for realizing OS FETs with enhanced performance, robust reliability, and back-end-of-line-compatible processing for future applications in M3D ICs.
- 5 October 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (14)
Overcoming the mobility–reliability trade-off in BEOL-compatible In2O3-based FETs through synergistic doping and prolonged annealing
Oxide semiconductors field-effect transistors (OS FETs) capable of simultaneously delivering high mobility and excellent reliability are a key platform for high-performance circuits and memory modules in monolithic three-dimensional integrated circuits (M3D ICs). In this work, we propose a synergistic strategy combining Zn doping and prolonged thermal annealing (PTA) to address the mobility–reliability trade-off in InZnOX FETs. The Zn doping ratio was controlled by adjusting the precursor-cycle ratio during atomic layer deposition. Zn incorporation suppresses channel crystallization during PTA, allowing the InZnOX channel to retain its amorphous structure. The results indicate that Zn doping effectively suppresses the hydrogen-related negative threshold-voltage shift (ΔVTH) and improves device reliability, while PTA mitigates the mobility degradation induced by doping and further enhances bias-stress stability. In particular, all PTA-treated InZnOX FETs exhibit mobilities exceeding 80 cm2 V−1 s−1, outperforming the InZnOX FETs without PTA. For PTA-treated devices with an In:Zn ratio of 22:1, a |ΔVTH| of only 11 mV after 1000 s of stress is achieved at 360 K under a gate-overdrive voltage of 4 V. These results demonstrate a feasible approach for realizing OS FETs with enhanced performance, robust reliability, and back-end-of-line-compatible processing for future applications in M3D ICs.
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (10) , 6063-6069
3-D-Stacked Oxide--Semiconductor 1T1C FeRAM With Ultralow-Voltage Operation via Coercive Field Reduction in ALD-HZO
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (10) , 6063-6069
3-D-Stacked Oxide--Semiconductor 1T1C FeRAM With Ultralow-Voltage Operation via Coercive Field Reduction in ALD-HZO
- Open Access
- 2 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (5) , 3157-3164
Exceptional Thickness Scalability of MFM Stack: Outstanding Performance in 3-nm TiN/3-nm HZO/3-nm TiN Capacitors
Advancing ultrahigh-density 3-D ferroelectric random-access memory (FeRAM) integration, we demonstrate excellent thickness scalability in fully ALD-deposited metal–ferroelectric–metal (MFM) stacks consisting of 3-nm TiN/3-nm HZO/3-nm TiN. These ultrathin devices exhibit robust ferroelectricity ( $2{P}_{\text {r}} \gt 22~{\mu }$ C/cm ${}^{{2}}\text {)}$ together with a record-low coercive voltage ( $2{V}_{\text {c}} \lt 0.65$ V). This breakthrough is enabled by a polycrystalline-to-amorphous transition in the TiN electrodes that occurs as they are thinned. This thickness-driven amorphization reduces the lattice mismatch with the ferroelectric o-phase, thereby promoting o-phase formation in HZO and enabling simultaneous downscaling of both HZO and TiN layers. Beyond reducing the overall stack thickness, thinner TiN electrodes also enhance reliability by providing smoother interfaces and suppressing oxygen scavenging, which together minimize leakage and increase breakdown strength. As a result, our ultrathin capacitors set several benchmarks for 3-nm ferroelectric layers, achieving an ultralow leakage current ( ${I}_{\text {leakage}} \lt 10^{-{3}}$ A/cm2 at 3 MV/cm), an ultrahigh breakdown field ( ${E}_{\text {BD}} \gt 9.5$ MV/cm), and durable endurance ( $\gt 10^{{11}}$ cycles) without ferroelectric failure (final $2{P}_{\text {r}} \gt 18~{\mu }$ C/cm2 and no electrical breakdown). Our work offers critical insights and unlocks new possibilities for pushing the boundaries of high-performance, ultradense, and low-power 3-D ferroelectric memories.
- 2 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (5) , 3157-3164
Open AccessExceptional Thickness Scalability of MFM Stack: Outstanding Performance in 3-nm TiN/3-nm HZO/3-nm TiN Capacitors
Advancing ultrahigh-density 3-D ferroelectric random-access memory (FeRAM) integration, we demonstrate excellent thickness scalability in fully ALD-deposited metal–ferroelectric–metal (MFM) stacks consisting of 3-nm TiN/3-nm HZO/3-nm TiN. These ultrathin devices exhibit robust ferroelectricity ( $2{P}_{\text {r}} \gt 22~{\mu }$ C/cm ${}^{{2}}\text {)}$ together with a record-low coercive voltage ( $2{V}_{\text {c}} \lt 0.65$ V). This breakthrough is enabled by a polycrystalline-to-amorphous transition in the TiN electrodes that occurs as they are thinned. This thickness-driven amorphization reduces the lattice mismatch with the ferroelectric o-phase, thereby promoting o-phase formation in HZO and enabling simultaneous downscaling of both HZO and TiN layers. Beyond reducing the overall stack thickness, thinner TiN electrodes also enhance reliability by providing smoother interfaces and suppressing oxygen scavenging, which together minimize leakage and increase breakdown strength. As a result, our ultrathin capacitors set several benchmarks for 3-nm ferroelectric layers, achieving an ultralow leakage current ( ${I}_{\text {leakage}} \lt 10^{-{3}}$ A/cm2 at 3 MV/cm), an ultrahigh breakdown field ( ${E}_{\text {BD}} \gt 9.5$ MV/cm), and durable endurance ( $\gt 10^{{11}}$ cycles) without ferroelectric failure (final $2{P}_{\text {r}} \gt 18~{\mu }$ C/cm2 and no electrical breakdown). Our work offers critical insights and unlocks new possibilities for pushing the boundaries of high-performance, ultradense, and low-power 3-D ferroelectric memories.
- 24 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (4) , 1882-1888
Area-Efficient BEOL-Compatible MFMIS FeFETs Enabled by a 3-D Multi-Fin Floating Gate Structure
In this work, we propose a 3-D multi-Fin floating gate (FG) structure to improve the area-efficiency of ferroelectric field-effect transistors (FeFETs) based on the metal–ferroelectric–metal–insulator–semiconductor (MFMIS) gate-stack. This architectural innovation exploits the additional channel surface provided by the vertical Fin sidewalls to minimize footprint area consumption while boosting the memory window (MW) of MFMIS FeFETs. Extensive experiments and analyses are conducted to demonstrate the feasibility and effectiveness of the proposed design. Atungsten (W) multi-Fin FG is successfully fabricated, featuring a Fin height of 93 nm and a width of 29 nm. Electrical characterization confirms that the 3-D FG structure enlarges the effective channel area without introducing significant tradeoffs in the key device characteristics of the baseline MIS FETs employing ALD-deposited ZnO channels. MFMIS FeFETs incorporating the multi-Fin FG structure achieve over 50% channel area saving. For devices with a footprint area ratio (AR) of 1:4 between the ferroelectric (FE) layer and the channel region, the proposed 3-D structure significantly enhances the MW from 1.3 to 2.9 V, surpassing that of planar devices with a footprint AR of 1:8. Furthermore, our 3-D multi-Fin FG FeFETs exhibit reliability on par with their planar counterparts, with endurance exceeding $2\times 10^{{9}}$ cycles and retention extrapolated beyond ten years. Our work presents a promising approach to addressing the area-inefficiency concern of MFMIS FeFETs.
- 24 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (4) , 1882-1888
Area-Efficient BEOL-Compatible MFMIS FeFETs Enabled by a 3-D Multi-Fin Floating Gate Structure
In this work, we propose a 3-D multi-Fin floating gate (FG) structure to improve the area-efficiency of ferroelectric field-effect transistors (FeFETs) based on the metal–ferroelectric–metal–insulator–semiconductor (MFMIS) gate-stack. This architectural innovation exploits the additional channel surface provided by the vertical Fin sidewalls to minimize footprint area consumption while boosting the memory window (MW) of MFMIS FeFETs. Extensive experiments and analyses are conducted to demonstrate the feasibility and effectiveness of the proposed design. Atungsten (W) multi-Fin FG is successfully fabricated, featuring a Fin height of 93 nm and a width of 29 nm. Electrical characterization confirms that the 3-D FG structure enlarges the effective channel area without introducing significant tradeoffs in the key device characteristics of the baseline MIS FETs employing ALD-deposited ZnO channels. MFMIS FeFETs incorporating the multi-Fin FG structure achieve over 50% channel area saving. For devices with a footprint area ratio (AR) of 1:4 between the ferroelectric (FE) layer and the channel region, the proposed 3-D structure significantly enhances the MW from 1.3 to 2.9 V, surpassing that of planar devices with a footprint AR of 1:8. Furthermore, our 3-D multi-Fin FG FeFETs exhibit reliability on par with their planar counterparts, with endurance exceeding $2\times 10^{{9}}$ cycles and retention extrapolated beyond ten years. Our work presents a promising approach to addressing the area-inefficiency concern of MFMIS FeFETs.
- 8 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (3) , 506-509
Multi-Grain Ferroelectric Induced Drain Current Variability in BEOL-Compatible OS FeFETs
In this work, we experimentally study intrinsic variability behaviors in back-end-of-line (BEOL)-compatible oxide-semiconductor ferroelectric field-effect transistors (OS FeFETs) under aggressive channel-length scaling down to 40 nm. Measurements on ZnO-channel OS FeFETs reveal two distinct trends: (i) a monotonic increase in coefficient of variance (COV) in drain-current during full switching (FSW), primarily governed by ferroelectric (FE) and process-induced variations; and (ii) an unexpected non-monotonic COV behavior under partial switching (PSW), attributed to stochastic percolation path formation on top of the process and ferroelectric (FE) variations including grain inhomogeneity (GI) in FSW. We modeled the DTD variations of OS FeFETs in FSW and PSW to gain physical insights into the origin of these trends, which are important for variation-aware device scaling optimization.
- 8 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (3) , 506-509
Multi-Grain Ferroelectric Induced Drain Current Variability in BEOL-Compatible OS FeFETs
In this work, we experimentally study intrinsic variability behaviors in back-end-of-line (BEOL)-compatible oxide-semiconductor ferroelectric field-effect transistors (OS FeFETs) under aggressive channel-length scaling down to 40 nm. Measurements on ZnO-channel OS FeFETs reveal two distinct trends: (i) a monotonic increase in coefficient of variance (COV) in drain-current during full switching (FSW), primarily governed by ferroelectric (FE) and process-induced variations; and (ii) an unexpected non-monotonic COV behavior under partial switching (PSW), attributed to stochastic percolation path formation on top of the process and ferroelectric (FE) variations including grain inhomogeneity (GI) in FSW. We modeled the DTD variations of OS FeFETs in FSW and PSW to gain physical insights into the origin of these trends, which are important for variation-aware device scaling optimization.
- 26 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (11) , 6034-6040
BTI Reliability of IGZTO FETs: Hydrogen Dynamics, AC/DC Stress Effects, and Advanced Modeling
This article presents an in-depth investigation into the role of hydrogen (H) in the reliability of indium–gallium–zinc–tin-oxide (IGZTO) field-effect transistors (FETs) under both direct current (dc) and alternating current (ac) stress conditions. By systematically examining the effects of H on negative bias temperature instability (NBTI) and positive bias temperature instability (PBTI), we provide critical insights into H-induced degradation mechanisms and their response to ac signals. Our findings reveal: 1) dc NBTI exhibits a saturation behavior with lower degradation severity compared to PBTI; 2) H+ ions in NBTI demonstrate a weak response to ac stress, leading to ultrastable ac reliability performance; and 3) electrochemical impedance spectroscopy (EIS) confirms the presence and migration dynamics of H+ ions in IGZTO FETs. A comprehensive model based on the collective behavior of H+ migration is proposed, accurately capturing the threshold voltage shift (ΔVth) under ac and dc BTI conditions. This study provides essential insights for enhancing the long-term reliability of oxide–semiconductor (OS) devices in advanced electronics.
- 26 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (11) , 6034-6040
BTI Reliability of IGZTO FETs: Hydrogen Dynamics, AC/DC Stress Effects, and Advanced Modeling
This article presents an in-depth investigation into the role of hydrogen (H) in the reliability of indium–gallium–zinc–tin-oxide (IGZTO) field-effect transistors (FETs) under both direct current (dc) and alternating current (ac) stress conditions. By systematically examining the effects of H on negative bias temperature instability (NBTI) and positive bias temperature instability (PBTI), we provide critical insights into H-induced degradation mechanisms and their response to ac signals. Our findings reveal: 1) dc NBTI exhibits a saturation behavior with lower degradation severity compared to PBTI; 2) H+ ions in NBTI demonstrate a weak response to ac stress, leading to ultrastable ac reliability performance; and 3) electrochemical impedance spectroscopy (EIS) confirms the presence and migration dynamics of H+ ions in IGZTO FETs. A comprehensive model based on the collective behavior of H+ migration is proposed, accurately capturing the threshold voltage shift (ΔVth) under ac and dc BTI conditions. This study provides essential insights for enhancing the long-term reliability of oxide–semiconductor (OS) devices in advanced electronics.
- 4 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (11) , 2066-2069
BEOL-Compatible Amorphous Oxide Semiconductor High-Voltage Transistors Achieving BFoM Beyond the GaAs Limit
Leveraging an offset top-gate (OTG) design and ALD-treated indium-tin oxide (ITO) channels, we present high-performance BEOL-compatible amorphous oxide semiconductor (AOS) high-voltage (HV) field-effect transistors (FETs). A long-channel (LC) FET features the highest Baliga’s figure of merit (BFoM) of 0.361 GW/cm2 among all AOS FETs, surpassing the one-dimensional GaAs limit. Additionally, a short-channel (SC) HV FET achieves a record-low specific on-state resistance (Ron, sp) of 9.15 × 10-2 mΩ·cm2. These results highlight the potential of AOS FETs for enabling high power density and efficiency in on-die power management and periphery applications for monolithic 3D integrated circuits (M3DICs).
- 4 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (11) , 2066-2069
BEOL-Compatible Amorphous Oxide Semiconductor High-Voltage Transistors Achieving BFoM Beyond the GaAs Limit
Leveraging an offset top-gate (OTG) design and ALD-treated indium-tin oxide (ITO) channels, we present high-performance BEOL-compatible amorphous oxide semiconductor (AOS) high-voltage (HV) field-effect transistors (FETs). A long-channel (LC) FET features the highest Baliga’s figure of merit (BFoM) of 0.361 GW/cm2 among all AOS FETs, surpassing the one-dimensional GaAs limit. Additionally, a short-channel (SC) HV FET achieves a record-low specific on-state resistance (Ron, sp) of 9.15 × 10-2 mΩ·cm2. These results highlight the potential of AOS FETs for enabling high power density and efficiency in on-die power management and periphery applications for monolithic 3D integrated circuits (M3DICs).
- 13 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (7) , 3535-3542
Investigating the Correlation Between Material Ferroelectricity and Silicon-Channel FeFET Performance: Insights for Material Engineering in Device Optimization
A systematic study was conducted in this work to investigate the influence of HfO2-based material ferroelectricity parameters on various device-level performance of silicon-channel ferroelectric (FE) field-effect transistors (Si FeFETs). Through extensive experiments, we have unearthed several key findings: (1) Reducing the remnant polarization (Pr) to an optimal value can effectively enhance endurance without significant memory window (MW) degradation. (2) Larger Pr exacerbates charge trapping (CT) during the writing operations but surprisingly improves the read-after-write (RAW) delay. This improvement is attributed to the opposing effects of the enlarged depolarization field and charge detrapping on the channel current. (3) For a fixed applied voltage that is effective for FE switching, a moderate increase in coercive electric field (EC) can co-optimize MW and retention characteristics without compromising endurance. Motivated by these observations, we developed a comprehensive model for Si FeFETs to provide an in-depth understanding of the underlying mechanisms and elucidate the intricate correlations between material and device characteristics. Through rigorous experiments and simulations, our work aims to provide guidelines for designing and optimizing Si FeFETs performance through material ferroelectricity engineering.
- 13 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (7) , 3535-3542
Investigating the Correlation Between Material Ferroelectricity and Silicon-Channel FeFET Performance: Insights for Material Engineering in Device Optimization
A systematic study was conducted in this work to investigate the influence of HfO2-based material ferroelectricity parameters on various device-level performance of silicon-channel ferroelectric (FE) field-effect transistors (Si FeFETs). Through extensive experiments, we have unearthed several key findings: (1) Reducing the remnant polarization (Pr) to an optimal value can effectively enhance endurance without significant memory window (MW) degradation. (2) Larger Pr exacerbates charge trapping (CT) during the writing operations but surprisingly improves the read-after-write (RAW) delay. This improvement is attributed to the opposing effects of the enlarged depolarization field and charge detrapping on the channel current. (3) For a fixed applied voltage that is effective for FE switching, a moderate increase in coercive electric field (EC) can co-optimize MW and retention characteristics without compromising endurance. Motivated by these observations, we developed a comprehensive model for Si FeFETs to provide an in-depth understanding of the underlying mechanisms and elucidate the intricate correlations between material and device characteristics. Through rigorous experiments and simulations, our work aims to provide guidelines for designing and optimizing Si FeFETs performance through material ferroelectricity engineering.