Dmytro Petrovych Koziarskyi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dmytro Petrovych Koziarskyi has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
- Ivan Petrovych Koziarskyi
Yuriy Fedkovych Chernivtsi National University
17 shared publications - Pavlo D. Maryanchuk
Yuriy Fedkovych Chernivtsi National University
8 shared publications - Eduard V. Maistruk
Yuriy Fedkovych Chernivtsi National University Kotsyubyns'kogo str. 2 58012 Chernivtsi Ukraine
7 shared publications - Ivan G. Orletskyi
Yuriy Fedkovych Chernivtsi National University
7 shared publications Eduard V. Maistruk
Chernivtsi Natl Univ, 2 Kotsubinsky Str, UA-58002 Chernovtsy, Ukraine
5 shared publications- Mariya I. Ilashchuk
Yuriy Fedkovych Chernivtsi National University
5 shared publications
Latest Publications
- 2 July 2026
- Published by Springer Nature
- p. 284-294
Single-Element Silicon p-i-n Photodiode with a Guard Ring, Isotype with the Substrate Material
- 2 July 2026
- Published by Springer Nature
- p. 284-294
Single-Element Silicon p-i-n Photodiode with a Guard Ring, Isotype with the Substrate Material
- Open Access
- 8 September 2025
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 3,p. 336-342
Electrical, Optical, and Structural Properties of Silicon n+-p Structures
The article investigates the structural, optical, and electrical properties of silicon n+-p structures. The experimental samples were made from high-resistance single-crystal silicon using two-stage phosphorus diffusion from solid-state planar sources. It was found that the introduction of phosphorus impurities with a concentration of 1.2∙1020 cm-3 provokes the formation of dislocations with a surface density of 2∙103-3∙103 cm-2 due to the formation and relaxation of mechanical stresses. The formation of a lightening oxide film on the silicon surface reduces the reflection coefficient by 25%. However, the formation of an n+-layer reduces the transmittance coefficient of the structure. It was established from the voltage-current characteristics of the n+-p structure under forward and reverse voltage bias, that in the temperature range T = 295–346 K, these structures have rectifying properties. At room temperature, the height of the potential barrier is 0.6 eV and decreases with temperature and its height at 0 K is 1.32 еV. At low forward biases, the dominant mechanism of current transport in the structure is superbarrier emission. With an increase in forward voltage from 0.1 V to 0.6 V, the generation-recombination mechanism prevails, and with an increase in temperature, an increase in the contribution of tunnel current is observed. At low reverse voltages, the I-V characteristics of diodes are well described by the formula for the generation current. The depth of occurrence of donor energy levels, from which thermal generation of charge carriers occurs is 0.15 eV.
- 8 September 2025
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 3,p. 336-342
Open AccessElectrical, Optical, and Structural Properties of Silicon n+-p Structures
The article investigates the structural, optical, and electrical properties of silicon n+-p structures. The experimental samples were made from high-resistance single-crystal silicon using two-stage phosphorus diffusion from solid-state planar sources. It was found that the introduction of phosphorus impurities with a concentration of 1.2∙1020 cm-3 provokes the formation of dislocations with a surface density of 2∙103-3∙103 cm-2 due to the formation and relaxation of mechanical stresses. The formation of a lightening oxide film on the silicon surface reduces the reflection coefficient by 25%. However, the formation of an n+-layer reduces the transmittance coefficient of the structure. It was established from the voltage-current characteristics of the n+-p structure under forward and reverse voltage bias, that in the temperature range T = 295–346 K, these structures have rectifying properties. At room temperature, the height of the potential barrier is 0.6 eV and decreases with temperature and its height at 0 K is 1.32 еV. At low forward biases, the dominant mechanism of current transport in the structure is superbarrier emission. With an increase in forward voltage from 0.1 V to 0.6 V, the generation-recombination mechanism prevails, and with an increase in temperature, an increase in the contribution of tunnel current is observed. At low reverse voltages, the I-V characteristics of diodes are well described by the formula for the generation current. The depth of occurrence of donor energy levels, from which thermal generation of charge carriers occurs is 0.15 eV.
- Open Access
- 13 March 2025
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (16) , 165106
Silicon p-i-n photodiode with reduced crystallographic defect density and structured surface
This paper reports new methods for reducing the density of structural defects on the surfaces of silicon p-i-n photodiodes (PDs). We experimentally proved that removing the silicon layer with packing defects, which are formed during oxidation, significantly contributes to reducing the density of the dislocations generated after phosphorus diffusion. Compared with the classical diffusion-planar technology for the preparation of silicon-based p-i-n PDs, our methods improve the parameters of PDs, especially dark current, sensitivity, noise equivalent power etc. Removal of the silicon layer is realized by carrying out chemical-dynamic polishing of the wafers after thermal oxidation in the areas of responsive elements. Although the optimum thickness of the etched silicon layer is about 2 μm, which corresponds to an etching time of 30 s, even taking into account the fact that the detector properties will deteriorate with increasing etching time, the change in the ‘maximum spectral response’ is positive. It is demonstrated that the chemical-dynamic polishing is a powerful tool to modify spectral characteristics of PD sensitivity. The maximum of the spectral response can be accurately tailored in a wide spectral range from by changing the chemical-dynamic polishing parameters.
- 13 March 2025
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (16) , 165106
Open AccessSilicon p-i-n photodiode with reduced crystallographic defect density and structured surface
This paper reports new methods for reducing the density of structural defects on the surfaces of silicon p-i-n photodiodes (PDs). We experimentally proved that removing the silicon layer with packing defects, which are formed during oxidation, significantly contributes to reducing the density of the dislocations generated after phosphorus diffusion. Compared with the classical diffusion-planar technology for the preparation of silicon-based p-i-n PDs, our methods improve the parameters of PDs, especially dark current, sensitivity, noise equivalent power etc. Removal of the silicon layer is realized by carrying out chemical-dynamic polishing of the wafers after thermal oxidation in the areas of responsive elements. Although the optimum thickness of the etched silicon layer is about 2 μm, which corresponds to an etching time of 30 s, even taking into account the fact that the detector properties will deteriorate with increasing etching time, the change in the ‘maximum spectral response’ is positive. It is demonstrated that the chemical-dynamic polishing is a powerful tool to modify spectral characteristics of PD sensitivity. The maximum of the spectral response can be accurately tailored in a wide spectral range from by changing the chemical-dynamic polishing parameters.
- 4 November 2024
- Published by Elsevier in Solid State Communications
- Vol. 395
Features of current flow in the n-CoFe2O4/n-CdTe heterojunction
- 4 November 2024
- Published by Elsevier in Solid State Communications
- Vol. 395
Features of current flow in the n-CoFe2O4/n-CdTe heterojunction
- Open Access
- 4 September 2023
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 8 (37) , 34146-34151
Electrical Properties of Anisotype ZnO:Al/n-ZnSe/p-CdTe Heterostructures
ZnO:Al/n-ZnSe/p-CdTe anisotype heterostructures with diode properties were fabricated by the high-frequency magnetron deposition of ZnO:Al and n-ZnSe thin films onto the surface of crystalline p-CdTe. The flow of currents limited by the space charge at forward voltages up to 0.45 V and tunneling currents at V > 0.45 V was established. A change in these current flow mechanisms was observed at reverse voltages V = -0.6 V. The main part of the energy barrier qf(k) = 1 eV of the ZnO:Al/n-ZnSe/p-CdTe heterostructure was formed in the p-CdTe substrate, which was established from studies of capacitance-voltage (C-V) characteristics. A model of the energy diagram of the heterostructure is proposed.
- 4 September 2023
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 8 (37) , 34146-34151
Open AccessElectrical Properties of Anisotype ZnO:Al/n-ZnSe/p-CdTe Heterostructures
ZnO:Al/n-ZnSe/p-CdTe anisotype heterostructures with diode properties were fabricated by the high-frequency magnetron deposition of ZnO:Al and n-ZnSe thin films onto the surface of crystalline p-CdTe. The flow of currents limited by the space charge at forward voltages up to 0.45 V and tunneling currents at V > 0.45 V was established. A change in these current flow mechanisms was observed at reverse voltages V = -0.6 V. The main part of the energy barrier qf(k) = 1 eV of the ZnO:Al/n-ZnSe/p-CdTe heterostructure was formed in the p-CdTe substrate, which was established from studies of capacitance-voltage (C-V) characteristics. A model of the energy diagram of the heterostructure is proposed.
- 10 May 2022
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 37 (6) , 065027
Photosensitive Schottky diodes based on nanostructured thin films of graphitized carbon formed on Cd1− x Zn x Te crystalline substrates
Photosensitive Schottky diodes of graphite/n-Cd1−x Zn x Te were obtained by depositing thin films of graphitized carbon on crystalline substrates of n-Cd1−x Zn x Te solid solution by electron beam evaporation. Based on the analysis of the single-phonon Raman spectra, it was found that the obtained films can be considered as nanocrystalline carbon structures with crystallite sizes of La ≈ 4.8 nm. From the research on the temperature dependencies of the I–V-characteristics and frequency dependencies of the C–V-characteristics, the main parameters of the structure were determined as well as the role of surface energy states in the formation of the profile of energy zones in the contact area. The main mechanisms of the forward and reverse currents are established. Using the diffusion theory of rectification, the height of the potential barrier was calculated and found to coincide with the experimentally determined value. A model of the diode energy diagram is proposed, which accurately describes the experimental electrophysical phenomena. The photoelectric properties of the graphite/n-Cd1−x Zn x Te diodes were studied.
- 10 May 2022
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 37 (6) , 065027
Photosensitive Schottky diodes based on nanostructured thin films of graphitized carbon formed on Cd1− x Zn x Te crystalline substrates
Photosensitive Schottky diodes of graphite/n-Cd1−x Zn x Te were obtained by depositing thin films of graphitized carbon on crystalline substrates of n-Cd1−x Zn x Te solid solution by electron beam evaporation. Based on the analysis of the single-phonon Raman spectra, it was found that the obtained films can be considered as nanocrystalline carbon structures with crystallite sizes of La ≈ 4.8 nm. From the research on the temperature dependencies of the I–V-characteristics and frequency dependencies of the C–V-characteristics, the main parameters of the structure were determined as well as the role of surface energy states in the formation of the profile of energy zones in the contact area. The main mechanisms of the forward and reverse currents are established. Using the diffusion theory of rectification, the height of the potential barrier was calculated and found to coincide with the experimentally determined value. A model of the diode energy diagram is proposed, which accurately describes the experimental electrophysical phenomena. The photoelectric properties of the graphite/n-Cd1−x Zn x Te diodes were studied.
- 21 December 2021
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12126, 503-510
UV sensitive heterojunction ZnCoO/n-GaP prepared by spray pyrolysis
The I-V and C-V–characteristics of the isotype Zn1-xCoxO/n-GaP heterojunction fabricated by spray pyrolysis of Zn1-xCoxO thin films on n-GaP crystalline substrates have been investigated and analyzed. The mechanisms of electron tunneling through the energy barrier of the heterojunction at forward and reverse currents and the conditions of generating reverse current are analyzed. The dynamics of changes in the capacitive parameters of Zn1-xCoxO thin film based on the C-V–characteristics is established. The photoelectric properties of the heterostructure are analyzed.
- 21 December 2021
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12126, 503-510
UV sensitive heterojunction ZnCoO/n-GaP prepared by spray pyrolysis
The I-V and C-V–characteristics of the isotype Zn1-xCoxO/n-GaP heterojunction fabricated by spray pyrolysis of Zn1-xCoxO thin films on n-GaP crystalline substrates have been investigated and analyzed. The mechanisms of electron tunneling through the energy barrier of the heterojunction at forward and reverse currents and the conditions of generating reverse current are analyzed. The dynamics of changes in the capacitive parameters of Zn1-xCoxO thin film based on the C-V–characteristics is established. The photoelectric properties of the heterostructure are analyzed.
- Open Access
- 1 January 2021
- Published by IOP Publishing in Materials Research Express
- Vol. 8 (1) , 015905
Electrical properties of heterostructures MnS/n-CdZnTe obtained by spray pyrolysis
The conditions for obtaining diode heterostructures of MnS/n-CdZnTe by the method of spray pyrolysis of MnS alabandite thin films on n-CdZnTe crystalline substrates were investigated. Based on the analysis of the temperature dependences of the I-V-characteristics, the mechanisms of the influence of electronic processes on the forward current in the MnS film are established. The mechanisms of current flow at reverse bias are revealed. The conditions for the formation of the energy barrier at the MnS/n-CdZnTe heterojunction and the influence on its parameters of the energy states at the semiconductor interface are studied. Based on the C-V-characteristics, the peculiarities of the distribution of electrically active impurities in the base region are investigated and the interaction of the alabandite film capacitance with the diffusion capacitance of the heterostructure is revealed. The proposed model of the energy diagram of the heterostructure well describes the experimental results.
- 1 January 2021
- Published by IOP Publishing in Materials Research Express
- Vol. 8 (1) , 015905
Open AccessElectrical properties of heterostructures MnS/n-CdZnTe obtained by spray pyrolysis
The conditions for obtaining diode heterostructures of MnS/n-CdZnTe by the method of spray pyrolysis of MnS alabandite thin films on n-CdZnTe crystalline substrates were investigated. Based on the analysis of the temperature dependences of the I-V-characteristics, the mechanisms of the influence of electronic processes on the forward current in the MnS film are established. The mechanisms of current flow at reverse bias are revealed. The conditions for the formation of the energy barrier at the MnS/n-CdZnTe heterojunction and the influence on its parameters of the energy states at the semiconductor interface are studied. Based on the C-V-characteristics, the peculiarities of the distribution of electrically active impurities in the base region are investigated and the interaction of the alabandite film capacitance with the diffusion capacitance of the heterostructure is revealed. The proposed model of the energy diagram of the heterostructure well describes the experimental results.
- 1 September 2020
- Published by IOP Publishing in Engineering Research Express
- Vol. 2 (3) , 035037
Influence of the base material on the interface properties of ZnO:Al/ n -CdS/ p -Cd 1−x Zn x Te heterojunctions
Researches of I – V -characteristics and C-V -characteristics of structures fabricated on unannealed and annealed at high temperature ( t = 900 °C) p -Cd 1−x Zn x Te substrates have been carried out. The influence of the intrinsic point defects system of the base material p -Cd 1−x Zn x Te on the interface properties of ZnO:Al/ n -CdS/ p -Cd 1−x Zn x Te heterojunctions have been studied. The above structures have been fabricated by sequential deposition of CdS and ZnO:Al thin films on crystalline p -Cd 1−x Zn x Te by high-frequency magnetron sputtering. Based on the analysis of the I – V -characteristics in the region of forward and reverse biases, the relationship between the physical processes during heat treatment and the structural perfection of the transition area of the studied heterojunctions have been established.
- 1 September 2020
- Published by IOP Publishing in Engineering Research Express
- Vol. 2 (3) , 035037
Influence of the base material on the interface properties of ZnO:Al/ n -CdS/ p -Cd 1−x Zn x Te heterojunctions
Researches of I – V -characteristics and C-V -characteristics of structures fabricated on unannealed and annealed at high temperature ( t = 900 °C) p -Cd 1−x Zn x Te substrates have been carried out. The influence of the intrinsic point defects system of the base material p -Cd 1−x Zn x Te on the interface properties of ZnO:Al/ n -CdS/ p -Cd 1−x Zn x Te heterojunctions have been studied. The above structures have been fabricated by sequential deposition of CdS and ZnO:Al thin films on crystalline p -Cd 1−x Zn x Te by high-frequency magnetron sputtering. Based on the analysis of the I – V -characteristics in the region of forward and reverse biases, the relationship between the physical processes during heat treatment and the structural perfection of the transition area of the studied heterojunctions have been established.
- 17 January 2020
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 35 (2) , 025018
Influence of properties of hematite films on electrical characteristics of isotype heterojunctions Fe 2 O 3 / n -CdTe
Conditions for the production of straightening isotype heterostructures n -Fe 2 O 3 / n -CdTe by spray-pyrolysis of thin films of hematite n -Fe 2 O 3 onto n -CdTe crystalline substrates were investigated. The presence of tunneling and space charge limits of the mechanisms of motion of electrons in the forward and reverse currents through the energy barrier of the heterojunction is established on the basis of the analysis of temperature dependences of I – V -characteristics. The role of energy states at the boundary of n -Fe 2 O 3 / n -CdTe in the formation of barrier parameters is determined. On the basis of the C – V -characteristics, the manifestation of the dielectric properties of the hematite film in a wide range of voltages is investigated. A model of the energy diagram of the heterostructure, which describes the experimental electrophysical phenomena well, has been proposed.
- 17 January 2020
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 35 (2) , 025018
Influence of properties of hematite films on electrical characteristics of isotype heterojunctions Fe 2 O 3 / n -CdTe
Conditions for the production of straightening isotype heterostructures n -Fe 2 O 3 / n -CdTe by spray-pyrolysis of thin films of hematite n -Fe 2 O 3 onto n -CdTe crystalline substrates were investigated. The presence of tunneling and space charge limits of the mechanisms of motion of electrons in the forward and reverse currents through the energy barrier of the heterojunction is established on the basis of the analysis of temperature dependences of I – V -characteristics. The role of energy states at the boundary of n -Fe 2 O 3 / n -CdTe in the formation of barrier parameters is determined. On the basis of the C – V -characteristics, the manifestation of the dielectric properties of the hematite film in a wide range of voltages is investigated. A model of the energy diagram of the heterostructure, which describes the experimental electrophysical phenomena well, has been proposed.