Kazuho Okada
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kazuho Okada has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Akinobu Shibata
Research Center for Structural Materials, National Institute for Materials Science
16 shared publications - Nobuhiro Tsuji
Department of Materials Science and Engineering, Kyoto University, Kyoto, Japan
6 shared publications Kaneaki Tsuzaki
4 shared publications- Xiaodong Lan
Research Center for Structural Materials, National Institute for Materials Science
4 shared publications Yazid Madi
4 shared publicationsAkiko Nakamura
3 shared publications
Latest Publications
- Open Access
- 30 December 2025
- Published by Elsevier in Scripta Materialia
- Vol. 274
Enhancing hydrogen embrittlement resistance in high-strength martensitic steels via tailoring variant selection at prior austenite grain boundaries
- 30 December 2025
- Published by Elsevier in Scripta Materialia
- Vol. 274
Open AccessEnhancing hydrogen embrittlement resistance in high-strength martensitic steels via tailoring variant selection at prior austenite grain boundaries
- Open Access
- 29 November 2025
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 950
Effects of prior austenite grain size on hydrogen embrittlement behavior in high-strength martensitic steel
- 29 November 2025
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 950
Open AccessEffects of prior austenite grain size on hydrogen embrittlement behavior in high-strength martensitic steel
- Open Access
- 30 October 2025
- Published by Elsevier in Acta Materialia
- Vol. 303
Origin of the trade-off relationship between tensile strength and hydrogen embrittlement resistance
- 30 October 2025
- Published by Elsevier in Acta Materialia
- Vol. 303
Open AccessOrigin of the trade-off relationship between tensile strength and hydrogen embrittlement resistance
- Open Access
- 29 June 2025
- Published by Wiley in Advanced Science
- Vol. 12 (33) , e04165
Fatigue Limit Doubling in High‐Strength Martensitic Steel through Crack Embryo Engineering–Cyclic‐Training‐Driven Self‐Optimization
Achieving superior fracture resistance under cyclic loading–specifically, a high‐fatigue limit–is crucial for ensuring structural safety and supporting a sustainable society. This study demonstrates a breakthrough in overcoming the conventional fatigue limit ceiling in high‐strength as‐quenched martensitic steel by enhancing resistance to crack initiation. In the as‐heat‐treated state, high‐angle boundaries with large elastic misfits and plastic incompatibility served as precursory sites for intrusions/extrusions (these are defined as “crack embryos”), eventually leading to fatigue crack initiation. Remarkably, after the pre‐fatigue training, surface crack initiation is entirely suppressed, doubling the fatigue limit with minimal change in tensile strength. A novel concept of “crack embryo engineering” is introduced, which targets the prevention of crack embryo formation by extracting intrinsic microstructural self‐optimization against fatigue deformation: macroscopic hardness homogenization and selective nano‐hardening of the precursory sites. This self‐optimization strategy offers a versatile approach to improving fatigue limit in general steels, providing an effective alternative to tempering heat treatment that inevitably sacrifices tensile strength.
- 29 June 2025
- Published by Wiley in Advanced Science
- Vol. 12 (33) , e04165
Open AccessFatigue Limit Doubling in High‐Strength Martensitic Steel through Crack Embryo Engineering–Cyclic‐Training‐Driven Self‐Optimization
Achieving superior fracture resistance under cyclic loading–specifically, a high‐fatigue limit–is crucial for ensuring structural safety and supporting a sustainable society. This study demonstrates a breakthrough in overcoming the conventional fatigue limit ceiling in high‐strength as‐quenched martensitic steel by enhancing resistance to crack initiation. In the as‐heat‐treated state, high‐angle boundaries with large elastic misfits and plastic incompatibility served as precursory sites for intrusions/extrusions (these are defined as “crack embryos”), eventually leading to fatigue crack initiation. Remarkably, after the pre‐fatigue training, surface crack initiation is entirely suppressed, doubling the fatigue limit with minimal change in tensile strength. A novel concept of “crack embryo engineering” is introduced, which targets the prevention of crack embryo formation by extracting intrinsic microstructural self‐optimization against fatigue deformation: macroscopic hardness homogenization and selective nano‐hardening of the precursory sites. This self‐optimization strategy offers a versatile approach to improving fatigue limit in general steels, providing an effective alternative to tempering heat treatment that inevitably sacrifices tensile strength.
- Open Access
- 16 April 2025
- Published by Elsevier in Scripta Materialia
- Vol. 264
Improving hydrogen embrittlement resistance in high-strength martensitic steels via thermomechanical processing
- 16 April 2025
- Published by Elsevier in Scripta Materialia
- Vol. 264
Open AccessImproving hydrogen embrittlement resistance in high-strength martensitic steels via thermomechanical processing
- 22 January 2025
- Published by Elsevier in Acta Materialia
- Vol. 287
Role of solute hydrogen on mechanical property enhancement in Fe–24Cr–19Ni austenitic steel: An in situ neutron diffraction study
- 22 January 2025
- Published by Elsevier in Acta Materialia
- Vol. 287
Role of solute hydrogen on mechanical property enhancement in Fe–24Cr–19Ni austenitic steel: An in situ neutron diffraction study
- Open Access
- 15 October 2024
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 64 (12) , 1847-1852
Real-time Observation of Stress-strain Behavior beyond Necking in Martensitic Steel by in-situ Synchrotron X-ray Diffraction
In general, the stress-strain relationship of materials obtained by standard uniaxial tensile test, which can identify the hardening behavior only up to necking. Beyond necking, the material behavior is usually estimated by extrapolating or numerical modelling based on hardening behavior prior to the uniform elongation. This study investigated the post-necking hardening behavior of a fully martensitic steel by in-situ synchrotron X-ray diffraction during tensile deformation. From the in-situ results, the dislocation density, lattice strain and phase stress were calculated within the necked region and outside the necked region. A near steady-state flow with some hardening was observed within the necked region of a martensitic steel. However, beyond uniform elongation, outside the necked region the dislocation density and phase stress decreased slightly, suggesting stress relaxation. Steady-state flow and dislocation densities at large strains suggest dynamic recovery occurs in the martensitic steel at room temperature.
- 15 October 2024
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 64 (12) , 1847-1852
Open AccessReal-time Observation of Stress-strain Behavior beyond Necking in Martensitic Steel by in-situ Synchrotron X-ray Diffraction
In general, the stress-strain relationship of materials obtained by standard uniaxial tensile test, which can identify the hardening behavior only up to necking. Beyond necking, the material behavior is usually estimated by extrapolating or numerical modelling based on hardening behavior prior to the uniform elongation. This study investigated the post-necking hardening behavior of a fully martensitic steel by in-situ synchrotron X-ray diffraction during tensile deformation. From the in-situ results, the dislocation density, lattice strain and phase stress were calculated within the necked region and outside the necked region. A near steady-state flow with some hardening was observed within the necked region of a martensitic steel. However, beyond uniform elongation, outside the necked region the dislocation density and phase stress decreased slightly, suggesting stress relaxation. Steady-state flow and dislocation densities at large strains suggest dynamic recovery occurs in the martensitic steel at room temperature.
- Open Access
- 1 September 2024
- Published by Iron and Steel Institute of Japan in Tetsu-to-Hagane
- Vol. 110 (11) , 890-898
Origin of Serrated Markings on the Hydrogen Related Quasi-cleavage Fracture in Low-carbon Steel with Ferrite Microstructure
A typical hydrogen-related transgranular fracture, namely quasi-cleavage fracture, is usually accompanied by serrated markings on the resultant fracture surfaces in steels with body-centered cubic phases. The present paper investigated the microscopic three-dimensional morphology and crystallographic feature of serrated markings in a 2Mn-0.1C steel mainly composed of ferrite microstructure. The serrated markings corresponded to the corners of the step-like morphologies which consisted of microscopic {011} facets whose longitudinal directions were almost parallel to or direction. In addition, the microscopic {011} quasi-cleavage facets had the largest inclination angle from tensile axis among six crystallographically equivalent {011} planes, suggesting that resolved normal stress imposed on the {011} plane is an important factor for the hydrogen-related quasi-cleavage fracture. We propose that not only the slip deformation enhanced by hydrogen but also the coalescence of vacancies/voids induced by hydrogen-enhanced plastic deformation should be considered for understanding the mechanism of the hydrogen-related quasi-cleavage fracture along the {011} planes.
- 1 September 2024
- Published by Iron and Steel Institute of Japan in Tetsu-to-Hagane
- Vol. 110 (11) , 890-898
Open AccessOrigin of Serrated Markings on the Hydrogen Related Quasi-cleavage Fracture in Low-carbon Steel with Ferrite Microstructure
A typical hydrogen-related transgranular fracture, namely quasi-cleavage fracture, is usually accompanied by serrated markings on the resultant fracture surfaces in steels with body-centered cubic phases. The present paper investigated the microscopic three-dimensional morphology and crystallographic feature of serrated markings in a 2Mn-0.1C steel mainly composed of ferrite microstructure. The serrated markings corresponded to the corners of the step-like morphologies which consisted of microscopic {011} facets whose longitudinal directions were almost parallel to or direction. In addition, the microscopic {011} quasi-cleavage facets had the largest inclination angle from tensile axis among six crystallographically equivalent {011} planes, suggesting that resolved normal stress imposed on the {011} plane is an important factor for the hydrogen-related quasi-cleavage fracture. We propose that not only the slip deformation enhanced by hydrogen but also the coalescence of vacancies/voids induced by hydrogen-enhanced plastic deformation should be considered for understanding the mechanism of the hydrogen-related quasi-cleavage fracture along the {011} planes.
- Open Access
- 14 August 2024
- Published by Elsevier in Acta Materialia
- Vol. 280
Effect of carbon segregation at prior austenite grain boundary on hydrogen-related crack propagation behavior in 3Mn-0.2C martensitic steels
- 14 August 2024
- Published by Elsevier in Acta Materialia
- Vol. 280
Open AccessEffect of carbon segregation at prior austenite grain boundary on hydrogen-related crack propagation behavior in 3Mn-0.2C martensitic steels
- Open Access
- 27 April 2024
- Published by Elsevier in Corrosion Science
- Vol. 233
Local crack arrestability and deformation microstructure evolution of hydrogen-related fracture in martensitic steel
- 27 April 2024
- Published by Elsevier in Corrosion Science
- Vol. 233
Open AccessLocal crack arrestability and deformation microstructure evolution of hydrogen-related fracture in martensitic steel