Kirsten Bobzin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kirsten Bobzin has a total of 65 co-authors. Here are the top co-authors by number of shared publications:
- Christian Kalscheuer
Surface Engineering Institute RWTH Aachen University Kackertstr. 15 52072 Aachen Germany
8 shared publications - Max Philip Möbius
Surface Engineering Institute RWTH Aachen University Kackertstr. 15 52072 Aachen Germany
7 shared publications C. Kalscheuer
Surface Engineering Institute (IOT), RWTH Aachen University, Aachen, Germany
6 shared publications- Hendrik Heinemann
Surface Engineering Institute RWTH Aachen: Rheinisch‐Westfalische Technische Hochschule Aachen Kackertstraße 15 52072 Aachen Germany
4 shared publications - Karsten Stahl
Technical University of Munich
4 shared publications - Marvin Erck
Surface Engineering Institute (IOT) RWTH Aachen University Kackertstraße 15 52072 AACHEN GERMANY
4 shared publications
Latest Publications
- Open Access
- 8 September 2026
- Published by Elsevier in SSRN Electronic Journal
Residual stresses in partially amorphous TiAlCrSiN coatings on cutting inserts
Residual stresses of nanocomposite TiAlCrSiN coatings, containing substantial amounts of amorphous phase, cannot be reliably measured with conventional methods like X-ray diffraction. The focused ion beam-digital image correlation (FIB-DIC) ring-core milling method offers an alternative to investigate the residual stresses of such coatings for qualification in tooling applications. This study aims to quantify the local residual stress state in partially amorphous TiAlCrSiN coatings deposited on cemented carbide cutting inserts to understand how coating architecture and thickness affect the resulting residual stresses. Monolayer TiAlCrSiN and bilayer TiAlCrSiN/TiAlCrSiON coatings with nominal thicknesses of s = 2 µm and s = 4 µm were deposited by high-power pulse magnetron sputtering. Local residual stresses near the cutting edge of the insert were determined using FIB-DIC ring-core milling. All coatings exhibited compressive residual stresses and a dense columnar morphology. Increasing thickness increased mean compressive residual stress from σr = -579 MPa to σr = -790 MPa for the monolayer and from σr = -117 MPa to σr = -822 MPa for the bilayer. The oxygen-containing bilayer with s = 2 µm showed markedly lower compressive stress than the corresponding monolayer, whereas the bilayer with s = 4 µm reached a stress level similar to the thicker monolayer. FIB-DIC ring-core milling provided a local quantitative comparison of residual stresses in the partially amorphous TiAlCrSiN-based coatings directly near the cutting edge of the inserts.
- 8 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessResidual stresses in partially amorphous TiAlCrSiN coatings on cutting inserts
Residual stresses of nanocomposite TiAlCrSiN coatings, containing substantial amounts of amorphous phase, cannot be reliably measured with conventional methods like X-ray diffraction. The focused ion beam-digital image correlation (FIB-DIC) ring-core milling method offers an alternative to investigate the residual stresses of such coatings for qualification in tooling applications. This study aims to quantify the local residual stress state in partially amorphous TiAlCrSiN coatings deposited on cemented carbide cutting inserts to understand how coating architecture and thickness affect the resulting residual stresses. Monolayer TiAlCrSiN and bilayer TiAlCrSiN/TiAlCrSiON coatings with nominal thicknesses of s = 2 µm and s = 4 µm were deposited by high-power pulse magnetron sputtering. Local residual stresses near the cutting edge of the insert were determined using FIB-DIC ring-core milling. All coatings exhibited compressive residual stresses and a dense columnar morphology. Increasing thickness increased mean compressive residual stress from σr = -579 MPa to σr = -790 MPa for the monolayer and from σr = -117 MPa to σr = -822 MPa for the bilayer. The oxygen-containing bilayer with s = 2 µm showed markedly lower compressive stress than the corresponding monolayer, whereas the bilayer with s = 4 µm reached a stress level similar to the thicker monolayer. FIB-DIC ring-core milling provided a local quantitative comparison of residual stresses in the partially amorphous TiAlCrSiN-based coatings directly near the cutting edge of the inserts.
- Open Access
- 27 July 2026
- Published by Elsevier in Surface and Coatings Technology
- Vol. 536
High-temperature crack behavior of Si-rich TiAlSiN coatings
- 27 July 2026
- Published by Elsevier in Surface and Coatings Technology
- Vol. 536
Open AccessHigh-temperature crack behavior of Si-rich TiAlSiN coatings
- Open Access
- 1 March 2026
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 57 (3) , 184-196
Effect of iron addition on the structure and tribological performance of CrAlN coatings
Hard coatings mitigate friction and wear of engineering components, while tribochemical interactions between lubricant and coating strongly influence performance. Masking ferrous surfaces with a coating reduces the effectiveness of additives optimized for steel. This study investigates iron as a triboactive element in CrAlN coatings, as iron and its oxides can catalyze lubricant hydrocarbon decomposition and promote low‐friction tribofilms. CrAlFeN coatings with up to x Fe = 7 at.‐% were deposited on steel substrates by magnetron sputtering. Their composition, surface morphology, and compound adhesion were characterized relative to an unmodified CrAlN reference. Tribological behavior was evaluated under boundary‐to‐mixed lubrication conditions in a polyalphaolefin oil with sulfur‐phosphorus additives using Si 3 N 4 counter bodies, ensuring that iron enters the contact exclusively via the coating. No detrimental changes in topography, morphology, or adhesion are observed upon iron addition. CrAlFeN coatings show reduced friction versus CrAlN, whereas all systems exhibit no measurable wear. Raman spectroscopy associates the friction reduction with the formation of a diamond‐like carbon resembling tribofilm, promoted by the catalytic effect of iron.
- 1 March 2026
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 57 (3) , 184-196
Open AccessEffect of iron addition on the structure and tribological performance of CrAlN coatings
Hard coatings mitigate friction and wear of engineering components, while tribochemical interactions between lubricant and coating strongly influence performance. Masking ferrous surfaces with a coating reduces the effectiveness of additives optimized for steel. This study investigates iron as a triboactive element in CrAlN coatings, as iron and its oxides can catalyze lubricant hydrocarbon decomposition and promote low‐friction tribofilms. CrAlFeN coatings with up to x Fe = 7 at.‐% were deposited on steel substrates by magnetron sputtering. Their composition, surface morphology, and compound adhesion were characterized relative to an unmodified CrAlN reference. Tribological behavior was evaluated under boundary‐to‐mixed lubrication conditions in a polyalphaolefin oil with sulfur‐phosphorus additives using Si 3 N 4 counter bodies, ensuring that iron enters the contact exclusively via the coating. No detrimental changes in topography, morphology, or adhesion are observed upon iron addition. CrAlFeN coatings show reduced friction versus CrAlN, whereas all systems exhibit no measurable wear. Raman spectroscopy associates the friction reduction with the formation of a diamond‐like carbon resembling tribofilm, promoted by the catalytic effect of iron.
- Open Access
- 31 December 2025
- Published by Elsevier in Tribology International
- Vol. 217
Wear protection for high-load chain drives by CrAlMoN coatings via PVD
- 31 December 2025
- Published by Elsevier in Tribology International
- Vol. 217
Open AccessWear protection for high-load chain drives by CrAlMoN coatings via PVD
- Open Access
- 3 September 2025
- Published by Taylor & Francis in Tribology Transactions
- Vol. 68 (5) , 1052-1068
Triboactive PVD Coatings for Solid Lubrication of Gears under High Loads
- 3 September 2025
- Published by Taylor & Francis in Tribology Transactions
- Vol. 68 (5) , 1052-1068
Open AccessTriboactive PVD Coatings for Solid Lubrication of Gears under High Loads
- 11 August 2025
- Published by Narr Francke Attempto Verlag GmbH + Co. KG in Tribologie und Schmierungstechnik
- Vol. 72 (2)
Dry Lubrication of Spur Gears Coated with CrAIN+Mo:W:S
Cylindrical gears are coated with CrAlN+Mo:W:S using High Power Pulsed Magnetron Sputtering and direct current Magnetron Sputtering. Their power loss, bulk temperature, and wear behavior are analyzed on the FZG gear efficiency test rig under dry lubrication. Coated and uncoated gears are examined using laser microscopy, energy-dispersive spectroscopy, and Raman spectroscopy. For operating points with low gear power loss, a tribofilm containing MoS2 as well as Mo and W oxides is detected on the pinion and wheel tooth flank, resulting in a stable tribosystem for several thousands load cycles. Cylindrical gear pairs with CrAlN+Mo:W:S coated wheels exhibit reduced power loss and lower bulk temperatures compared to uncoated gears.
- 11 August 2025
- Published by Narr Francke Attempto Verlag GmbH + Co. KG in Tribologie und Schmierungstechnik
- Vol. 72 (2)
Dry Lubrication of Spur Gears Coated with CrAIN+Mo:W:S
Cylindrical gears are coated with CrAlN+Mo:W:S using High Power Pulsed Magnetron Sputtering and direct current Magnetron Sputtering. Their power loss, bulk temperature, and wear behavior are analyzed on the FZG gear efficiency test rig under dry lubrication. Coated and uncoated gears are examined using laser microscopy, energy-dispersive spectroscopy, and Raman spectroscopy. For operating points with low gear power loss, a tribofilm containing MoS2 as well as Mo and W oxides is detected on the pinion and wheel tooth flank, resulting in a stable tribosystem for several thousands load cycles. Cylindrical gear pairs with CrAlN+Mo:W:S coated wheels exhibit reduced power loss and lower bulk temperatures compared to uncoated gears.
- Open Access
- 11 May 2025
- Published by Wiley in Steel Research International
- Vol. 96 (11) , 350-358
Joining Stainless Steel with a Novel Fe‐Based Amorphous Brazing Foil
In the field of brazing, flexible foils with an amorphous microstructure are often used for joining complex component geometries such as plate heat exchangers. These foils are mostly Ni based, which has numerous disadvantages in terms of economy, ecology, and health. Therefore, the substitution of Ni with the less critical element Fe is desirable. With the use of ThermoCalc calculations, a novel Fe‐based amorphous brazing foil is developed. This foil, produced by rapid solidification technology, is now brazed with X5CrNi18‐10 in a vacuum brazing process at T = 1200 °C with varying brazing times. The quality of the joints is investigated using scanning electron microscopy/energy dispersive X‐ray spectroscopy (SEM/EDS), ultrasonic c‐scan, and shear test. Material‐bonded joints with good wetting are produced. Increasing the brazing time from t b = 10 to t b = 30 min leads to an improvement in shear strength of approx. Δ τ Shear = 60 MPa, while no further improvement is achieved with t b = 120 min. SEM/EDS examinations show the formation of Cr‐borides in the diffusion‐affected zone. The novel development and further optimization of Fe‐based amorphous brazing foils combines two definitive advantages for brazing: flexibility of amorphous foils and substitution of Ni with cost‐effective, environmentally friendly Fe.
- 11 May 2025
- Published by Wiley in Steel Research International
- Vol. 96 (11) , 350-358
Open AccessJoining Stainless Steel with a Novel Fe‐Based Amorphous Brazing Foil
In the field of brazing, flexible foils with an amorphous microstructure are often used for joining complex component geometries such as plate heat exchangers. These foils are mostly Ni based, which has numerous disadvantages in terms of economy, ecology, and health. Therefore, the substitution of Ni with the less critical element Fe is desirable. With the use of ThermoCalc calculations, a novel Fe‐based amorphous brazing foil is developed. This foil, produced by rapid solidification technology, is now brazed with X5CrNi18‐10 in a vacuum brazing process at T = 1200 °C with varying brazing times. The quality of the joints is investigated using scanning electron microscopy/energy dispersive X‐ray spectroscopy (SEM/EDS), ultrasonic c‐scan, and shear test. Material‐bonded joints with good wetting are produced. Increasing the brazing time from t b = 10 to t b = 30 min leads to an improvement in shear strength of approx. Δ τ Shear = 60 MPa, while no further improvement is achieved with t b = 120 min. SEM/EDS examinations show the formation of Cr‐borides in the diffusion‐affected zone. The novel development and further optimization of Fe‐based amorphous brazing foils combines two definitive advantages for brazing: flexibility of amorphous foils and substitution of Ni with cost‐effective, environmentally friendly Fe.
- Open Access
- 18 February 2025
- Published by Springer Nature in Welding in the World
- Vol. 69 (6) , 1697-1704
Dissolving brittle phases in Ni-based filler metals by adding W
Brazing hot work steel is a popular method used in the production of casting tools. Usually, Ni-based alloy Ni 620 serves as the preferred filler metal. However, incorporating metalloids such as B and Si to lower the melting point can result in unwanted intermetallic phase formation within the joint. These phases can adversely affect the mechanical characteristics. Hence, it is vital to reduce intermetallic phase formation during brazing to maintain optimal mechanical properties. The research concentrates on W inoculation of Ni 620 to alter the microstructure of the joint. The alloys are produced via melt spinning, and their solidus and liquidus temperatures are investigated using DSC measurements. Next, X37CrMoV5-1 hot work steel samples are brazed in a vacuum furnace. The microstructure is then studied using SEM/EDS, and their hardness properties are evaluated using nanoindentation. Furthermore, their strength is analyzed in the shear test. Incorporating W into Ni 620 when brazing hot work steel alters the presence of brittle phases and hardness characteristics. Particularly, introducing W leads to a significant decrease in hardness, resulting in a more even distribution of hardness throughout the joining area. Using W to modify Ni 620 proves to be advantageous for improving hardness properties when brazing hot work steel.
- 18 February 2025
- Published by Springer Nature in Welding in the World
- Vol. 69 (6) , 1697-1704
Open AccessDissolving brittle phases in Ni-based filler metals by adding W
Brazing hot work steel is a popular method used in the production of casting tools. Usually, Ni-based alloy Ni 620 serves as the preferred filler metal. However, incorporating metalloids such as B and Si to lower the melting point can result in unwanted intermetallic phase formation within the joint. These phases can adversely affect the mechanical characteristics. Hence, it is vital to reduce intermetallic phase formation during brazing to maintain optimal mechanical properties. The research concentrates on W inoculation of Ni 620 to alter the microstructure of the joint. The alloys are produced via melt spinning, and their solidus and liquidus temperatures are investigated using DSC measurements. Next, X37CrMoV5-1 hot work steel samples are brazed in a vacuum furnace. The microstructure is then studied using SEM/EDS, and their hardness properties are evaluated using nanoindentation. Furthermore, their strength is analyzed in the shear test. Incorporating W into Ni 620 when brazing hot work steel alters the presence of brittle phases and hardness characteristics. Particularly, introducing W leads to a significant decrease in hardness, resulting in a more even distribution of hardness throughout the joining area. Using W to modify Ni 620 proves to be advantageous for improving hardness properties when brazing hot work steel.
- Open Access
- 29 November 2023
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 54 (11) , 1340-1349
Design and characterization of novel iron‐based amorphous brazing foils based on thermodynamic predictions
Amorphous brazing foils facilitate the brazing process due to their high flexibility. Nickel‐based amorphous brazing foils are already in industrial use. However, as the raw material price for nickel is continuously increasing, more cost‐efficient iron‐based amorphous brazing foils are currently the focus of research. In this study, three alloys in the quinary system iron‐nickel‐chrom‐silicon‐boron will be investigated, which, according to previous predictions of newly developed thermodynamic databases, should exhibit an increased glass forming ability. The production and the characterization of the new iron‐based foils will in turn serve to validate the newly developed thermodynamic databases. With one of the alloys, a new iron‐based partly amorphous brazing foil can successfully be produced, but the other two alloys are too brittle for the brazing process. The results of this study not only show that the newly developed thermodynamic database of the quinary iron‐nickel‐chrome‐silicon‐boron alloy system can provide suitable prediction on the microstructure and melting behavior of the corresponding alloys, but also that it is possible to produce a quaternary iron‐based partly amorphous foil.
- 29 November 2023
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 54 (11) , 1340-1349
Open AccessDesign and characterization of novel iron‐based amorphous brazing foils based on thermodynamic predictions
Amorphous brazing foils facilitate the brazing process due to their high flexibility. Nickel‐based amorphous brazing foils are already in industrial use. However, as the raw material price for nickel is continuously increasing, more cost‐efficient iron‐based amorphous brazing foils are currently the focus of research. In this study, three alloys in the quinary system iron‐nickel‐chrom‐silicon‐boron will be investigated, which, according to previous predictions of newly developed thermodynamic databases, should exhibit an increased glass forming ability. The production and the characterization of the new iron‐based foils will in turn serve to validate the newly developed thermodynamic databases. With one of the alloys, a new iron‐based partly amorphous brazing foil can successfully be produced, but the other two alloys are too brittle for the brazing process. The results of this study not only show that the newly developed thermodynamic database of the quinary iron‐nickel‐chrome‐silicon‐boron alloy system can provide suitable prediction on the microstructure and melting behavior of the corresponding alloys, but also that it is possible to produce a quaternary iron‐based partly amorphous foil.
- 7 November 2023
- Published by Elsevier in Surface and Coatings Technology
- Vol. 475
Triboactive CrAlN+MoWS coatings deposited by pulsed arc PVD
- 7 November 2023
- Published by Elsevier in Surface and Coatings Technology
- Vol. 475
Triboactive CrAlN+MoWS coatings deposited by pulsed arc PVD