YXYouze Xin

Youze Xin

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Youze Xin has a total of 55 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A Vertically Stacked Dual-Junction SPAD for Wide Spectral Response

    by Bing Zhang, Pengfei Hu, Congzhen Hu, Yiyun Xie, Chi Wang, Youze Xin, RuBin Yan, Li Geng

    This article presents a wide spectral response single-photon avalanche diode (SPAD) fabricated in a 110 nm CMOS image sensor (CIS) technology. The device integrates two vertically stacked avalanche multiplication regions comprising a shallow P++/ N-enrichment layer junction and a deeper n-type buried layer (NBL) / deep p-type buried layer (DPBL) junction, respectively. Measurement results show a peak photon detection probability (PDP) of 82% at 600 nm, with a broadband PDP exceeding 18% across 400–850 nm under an excess bias voltage of 5.0 V. At room temperature, the SPAD exhibits a moderate dark count rate (DCR) of ∼65 cps/μm². The temporal resolution corresponds to a full-width-at-half-maximum (FWHM) jitter of 69 ps at 450 nm and 110 ps at 905 nm, respectively. Owing to its vertically stacked dual-junction design, the proposed SPAD provides a compact pixel solution suitable for applications requiring operation from visible to NIR wavelengths.

  • A 0.0075 mm 2 , 0.0139 FoM Double-Ring Vernier TDC With Vernier Arbiter Phase Calibration and Code Error Cancellation for 26 dB SFDR Improvement in ToF-PET

    by Han Wang, Youze Xin, Yiyun Xie, Pengfei Hu, Hongxu Chen, Ziyang Xu, Xuhu Wang, Congzhen Hu, Chi Wang, Lu Li, et al.

    This work presents a PET-oriented double-ring Vernier time-to-digital converter (DRVTDC) that targets the timing-quantization block required in multi-voltage-threshold (MVT) and time-over-threshold (ToT) front-end readout for time-of-flight (ToF) positron emission tomography (PET) applications. This work addresses two critical error mechanisms that limit the use of multi-stage Vernier TDCs: parallel output misalignment (POM) between quantization stages and mismatch-induced chasing error (MCE) in the Vernier arbiter array. To suppress these errors, a joint calibration scheme combining code error cancellation (CEC) and Vernier arbiter phase calibration (VAPC) is proposed. The core TDC achieves a 10.4-ps resolution with only 0.0075 mm2 core area. The implemented 7-bit coarse counter provides a dynamic range (DR) of 5.12 μs. Empowered by these techniques, the measured DNL and INL ranges are significantly improved from +3.17/-0.89 LSB and +7.0/-6.9 LSB to +0.34/-0.29 LSB and +1.15/-1.09 LSB, respectively, alongside a 26-dB enhancement in the SFDR. The core TDC consumes 1.758 mW, with a total of 5.526 mW including the PLLs.

  • An Active Multipower Emission Strategy for Time Walk-Error Compensation in SiPM-Based d-ToF LiDAR

    by Pengfei Hu, Youze Xin, Xuhu Wang, Yiyun Xie, Han Wang, Chi Wang, Bing Zhang, Congzhen Hu, Li Geng

    Time walk error significantly impacts the accuracy of distance measurements in direct time-of-flight (d-ToF) LiDAR systems. A system-level d-ToF model that comprehensively accounts for the mechanisms is established in this paper. Then, an active multi-power excitation (AMPE) strategy is proposed and verified in a silicon photomultiplier (SiPM)-based d-ToF LiDAR. Compared with conventional passive correction methods, AMPE actively injects known excitation constraints into the measurement process. It exploits the relationship between emission energy and threshold-crossing time by transmitting pulses with controlled power using a customized compensation algorithm. The core strength of this method is that it transforms the correction problem into a constrained estimation problem governed by emission control, thereby avoiding complex receiver-side timing circuitry and extensive offline calibration. A prototyped LiDAR system is developed, and experimental results demonstrate that more than a 72% reduction in walk error induced depth distortion is achieved with only 10 measurements per range point, enabling reliable 200 m operation under 60 klux ambient illumination. The proposed method establishes a novel time walk error compensation strategy, enhancing the energy efficiency and wide dynamic range of d-ToF LiDAR applications.


  • Hardware-Accelerated ASIC and Cardiac Monitoring System for Wearable Devices

    by Cheng Zhang, Rui Xing, Meng Cao, Zhuoqi Guo, Youze Xin, Bing Zhang, Zhongming Xue, Li Geng

    Cardiac arrhythmia is a common and potentially life-threatening cardiovascular disorder, requiring timely and accurate detection. This article presents an ultralow-power application-specific integrated circuit (ASIC) for real-time multiclass arrhythmia classification in wearable electrocardiography (ECG) monitoring. Unlike present works that require high computational resources or use limited resources for binary or small-category classification, this work proposes a hardware-friendly ASIC to support seven categories of cardiac arrhythmia classification based on the Association for the Advancement of Medical Instrumentation (AAMI) standard, outperforming most existing chips. Through a shared discrete wavelet transform (DWT) module and an optimized support vector machine (SVM) core, the hardware resources are reduced by over 30% for the optimized SVM and by over 75% when both optimizations are applied together. Through optimized circuit design and low-power design, this ASIC can maintain a high accuracy of 97.2% and an ultralow power consumption of 35.5 nJ/inference, which is lower than most of the existing tasks. This work uses an efficient hardware design to reduce the hardware complexity, making it suitable for wearable devices that require low power consumption. Operating at a frequency of 50 MHz, the ASIC is faster than other deep learning accelerators, enabling rapid on-device detection for early intervention and cloud-assisted diagnosis. A system-level verification was performed to prove the feasibility of ASIC in real scenarios of a 475 mW system power.


  • A Cryo-Tolerant >40-dB IRR, 4.7–7.9-GHz Double Quadrature Cryo-CMOS Receiver With a Broadband LNA for Scalable Quantum Applications

    by Zixun Gao, Chenglong Liang, Ruixin Liang, Suyuan Gan, Bingjun Tang, Xingguo Dong, Ya Zhao, Youze Xin, Bing Zhang, Li Geng

    This article presents a cryogenic CMOS receiver operating across 4.7–7.9 GHz for frequency-division multiplexing (FDM) quantum state readout. The designed receiver employs a double quadrature (DQ) architecture and a hybrid poly-phase filter (PPF) is proposed to achieve an impressive image rejection ratio (IRR) to meet the 99.99% higher fidelity requirements in quantum error correction (QEC). In addition, gain tuning at different stages of the low noise amplifier (LNA) facilitates a broadband gain and flatness, while the subsequent receiver chains of a broadband mixer and an improved four-input intermediate frequency amplifier (IF-AMP) provide further gain compensation. Fabricated with a standard 55-nm CMOS technology, the LNA achieves a measured power gain of 27.4 dB, with a −3-dB bandwidth (BW) of 5.2 GHz at 6 K. The measured cryogenic noise figure (NF) ranges from 0.79 to 1 dB consuming merely 5.5 mW from a 1.2-V supply. Overall receiver measurements demonstrate a peak gain of 48.2 dB, a −5-dB flatness of 3.2 GHz, and an IRR that exceeds 40 dB at 6 K. These results demonstrate the receiver’s capacity for high-fidelity qubits’ state readout.


  • A Compact Wideband Simultaneous Noise and Input Matching Method Based on Three-Coil Transformer With Capacitor Assistance for LNA Design

    by Chenglong Liang, Ruixin Liang, Suyuan Gan, Bingjun Tang, Zixun Gao, Qian Dong, Zhaoyang Ma, Youze Xin, Yi Xie, Bing Zhang, et al.

    A method for achieving wideband simultaneous noise and input matching (SNIM) based on traditional higher order networks has been analyzed and improved through capacitor-assisted techniques. Subsequently, a new wideband SNIM approach, utilizing a three-coil transformer combined with capacitor assistance, is proposed. Without altering the conventional topological structure, the introduction of the coupling factor significantly reduced the chip area and the noise contribution from passive components, thereby lowering the overall noise figure (NF). To validate the design, a C-band two-stage current-reused low-noise amplifier (LNA) was designed with a 55-nm CMOS process. The measurement results indicate that S11 is below −10dB across a wideband of 2.5–8.5 GHz. A power gain of 24.6dB is achieved at 5 GHz with −3-dB bandwidth of 4.8 GHz. The noise matching discrepancy (NF-NFmin) remains 0.15dB within the band range of 4.2–8.5 GHz, and NF maintains below 2dB, while the power consumption is only 9.1 mW.


  • A Low-Power i-ToF LiDAR With Nonlinearity Self-Calibration Technique

    by Youze Xin, Bing Zhang, Congzhen Hu, Yiyun Xie, Pengfei Hu, Ruipeng Yang, Yaoxin Li, Dan Li, Li Geng

    This paper proposes a low power 320×240 indirect time of flight (i-ToF) vision system with non-linearity self-calibration technique. A pump gate modulator (PGM) technique is applied in the pixel to reduce the power consumption of pixel modulation. As a result, the pixel has a higher lateral electric field in lower voltage swing of modulation and the pixel can operate in the depletion state to achieve smaller load capacitance. To improve the non-linearity of the sensor, non-linearity self-calibration techniques are proposed. It includes channel toggle technique and pre-distortion single slop analog-to-digital converter (SS-AdC) which eliminates the quadratic non-linearity in the readout channel and source follower (SF) non-linearity in the pixel, respectively. Furthermore, it reduces the difficulty of nonlinear calibration of different batches of chips. The measured non-linearity decreases greatly without back-end calibration, which is smaller than 0.8 % within the distance range from 0.12 m to 5 m. The receiver chip is fabricated in 110 nm front-side illuminated (FSI) process with 5.6 μm×5.6 μm pixel size. The chip power is only 130 mW.


  • A Backside-Illuminated 3.5 μm Pixel With 86% Demodulation Contrast at 1.0 V Voltage Swing for Indirect Time-of-Flight Image Sensors

    by Congzhen Hu, Bing Zhang, Youze Xin, Chi Wang, Yiyun Xie, Pengfei Hu, Zungui Ke, Li Geng

    This article presents a 3.5 $\mu$ m stacked backside-illuminated (BSI) indirect time-of-flight (i-ToF) pixel fabricated in a 65-nm CMOS image sensors (CIS) process. Transfer gate-induced lateral electric field control of charge transfer is one of the most relied techniques for implementing i-ToF image sensors. However, the transfer gate as modulated gate usually needs a high voltage swing to achieve high demodulation contrast (DC). We introduce a photonic demodulator pixel that utilizes a new lateral electric field modulation technology to achieve a 1.0 V modulation voltage swing while maintaining a high DC of 86% at 100 MHz modulation frequency. The proposed method employs a gate-controlled junction field effect transistor (JFET) to control the drain-induced barrier lowering (DIBL) effect to modulate the lateral electric field. In addition, the photonic demodulator can be also fully depleted with an N-type epitaxy for 22% quantum efficiency (QE) enhancement at 940 nm. This development can greatly lower the power consumption for high-resolution i-ToF sensor applications.

  • Analytical Modeling of Charge Behavior in Pinned Photodiode for CMOS Image Sensors

    by Congzhen Hu, Bing Zhang, Youze Xin, Yiyun Xie, Pengfei Hu, Li Geng

    The thermionic emission mechanism is usually employed to model the charge packet which is not affected by the potential barrier, however, the electric fields induced by the charge itself are not included in previous work. We introduce a proposed physical-based model to characterize the whole charge behavior characteristics of the pinned photodiode (PPD) when employing the thermal diffusion, self-induced drifting, and thermionic emission mechanisms together. In addition, the dynamic PPD parameters such as PPD capacitance ( C PPD ), PPD potential ( V PPD ), and charge transfer potential barrier ( V B ) are included to characterize the integration and transfer process together based on iterative methods. The model is verified with technology computer-aided design (TCAD) simulations and the test devices were fabricated in a 0.11 μm CMOS image sensor (CIS) process. The proposed analytical behavior model presents a great convenience for circuit-level simulation of the PPD-based pixels.