Junrui Lyu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Junrui Lyu has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Srabanti Chowdhury
Stanford University
3 shared publications A. Kasperovich
Stanford University , 450 Jane Stanford Way, Stanford, California 94305
2 shared publicationsH. Sena
Stanford University , 450 Jane Stanford Way, Stanford, California 94305
2 shared publicationsHao Wu
2 shared publications- Kelly Woo
Stanford University , 450 Jane Stanford Way, Stanford, California 94305
2 shared publications - Mohamadali Malakoutian
Stanford University , 450 Jane Stanford Way, Stanford, California 94305
2 shared publications
Latest Publications
- 1 April 2026
- Published by AIP Publishing in APL Materials
- Vol. 14 (4)
Publisher’s Note: “Diamond thermal matrix demonstration for two-tier 3D integrated circuits” [APL Mater. 13, 041108 (2025)]
- 1 April 2026
- Published by AIP Publishing in APL Materials
- Vol. 14 (4)
Publisher’s Note: “Diamond thermal matrix demonstration for two-tier 3D integrated circuits” [APL Mater. 13, 041108 (2025)]
- Open Access
- 1 December 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 138 (21)
720 V quasi-vertical GaN-on-silicon p–n diodes with surge capability fabricated using selective area growth
This work demonstrates, for the first time, avalanche breakdown capability in quasi-vertical gallium nitride (GaN) on silicon (Si) substrates employing localized epitaxial growth. On industry-standard 200 mm wafers, we integrated an 8 μm thick GaN drift layer onto Si, enabling the fabrication of 720 V quasi-vertical p–n diodes. This method yields high-performance power devices in CMOS-compatible cleanrooms at a reduced cost. The GaN p–n junctions exhibit a specific on-resistance of 3.3 mΩ cm2, a current on/off ratio exceeding 1010, and a current density of 1.4 kA/cm2 at 10 V. Robust avalanche behavior was confirmed through temperature-dependent reverse bias measurements from 298 to 373 K, and over 3000 over-voltage surge ruggedness was demonstrated by unclamped inductive switching stress tests. These results underscore the advantages of localized epitaxy for achieving high-quality GaN layers on Si, paving the way for scalable integration of high-voltage GaN power devices with conventional Si technology.
- 1 December 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 138 (21)
Open Access720 V quasi-vertical GaN-on-silicon p–n diodes with surge capability fabricated using selective area growth
This work demonstrates, for the first time, avalanche breakdown capability in quasi-vertical gallium nitride (GaN) on silicon (Si) substrates employing localized epitaxial growth. On industry-standard 200 mm wafers, we integrated an 8 μm thick GaN drift layer onto Si, enabling the fabrication of 720 V quasi-vertical p–n diodes. This method yields high-performance power devices in CMOS-compatible cleanrooms at a reduced cost. The GaN p–n junctions exhibit a specific on-resistance of 3.3 mΩ cm2, a current on/off ratio exceeding 1010, and a current density of 1.4 kA/cm2 at 10 V. Robust avalanche behavior was confirmed through temperature-dependent reverse bias measurements from 298 to 373 K, and over 3000 over-voltage surge ruggedness was demonstrated by unclamped inductive switching stress tests. These results underscore the advantages of localized epitaxy for achieving high-quality GaN layers on Si, paving the way for scalable integration of high-voltage GaN power devices with conventional Si technology.
- Open Access
- 1 April 2025
- Published by AIP Publishing in APL Materials
- Vol. 13 (4)
Diamond thermal matrix demonstration for two-tier 3D integrated circuits
A diamond matrix scaffold is crucial for 3D dense chips because it provides exceptional thermal management due to its excellent thermal conductivity. Diamond can also replace copper thermal vias, enabling efficient heat transfer and improved cooling performance. Its low thermal boundary resistance with Si and dielectrics (such as SiO2) ensures minimal thermal bottlenecks, enhancing the 3D chip’s overall thermal management and reliability. For the first time, we have demonstrated a BEOL-compatible two-tier diamond matrix scaffold experimentally in combination with SiO2 and on top of a Si wafer. The diamond was nucleated and grown conformally in the via holes with 1:3, 1:2, 1:1, and 2:1 (width:height) aspect ratios to form the via. A relatively low residual stress of 0.35–0.9 GPa and an FWHM as low as 4.3 cm−1 were measured using Raman spectroscopy. The (111) plane was measured as the dominating plane after the growth on top, while the (110) plane was the dominating plane inside the trenches mid-growth. This highly thermally conductive diamond matrix (thermal conductivity between 500 and 1800 W/m/K) can be used not only for Si technology but also for GaN and Ga3O2 technologies to push the boundaries of output power by lowering the junction/channel temperature.
- 1 April 2025
- Published by AIP Publishing in APL Materials
- Vol. 13 (4)
Open AccessDiamond thermal matrix demonstration for two-tier 3D integrated circuits
A diamond matrix scaffold is crucial for 3D dense chips because it provides exceptional thermal management due to its excellent thermal conductivity. Diamond can also replace copper thermal vias, enabling efficient heat transfer and improved cooling performance. Its low thermal boundary resistance with Si and dielectrics (such as SiO2) ensures minimal thermal bottlenecks, enhancing the 3D chip’s overall thermal management and reliability. For the first time, we have demonstrated a BEOL-compatible two-tier diamond matrix scaffold experimentally in combination with SiO2 and on top of a Si wafer. The diamond was nucleated and grown conformally in the via holes with 1:3, 1:2, 1:1, and 2:1 (width:height) aspect ratios to form the via. A relatively low residual stress of 0.35–0.9 GPa and an FWHM as low as 4.3 cm−1 were measured using Raman spectroscopy. The (111) plane was measured as the dominating plane after the growth on top, while the (110) plane was the dominating plane inside the trenches mid-growth. This highly thermally conductive diamond matrix (thermal conductivity between 500 and 1800 W/m/K) can be used not only for Si technology but also for GaN and Ga3O2 technologies to push the boundaries of output power by lowering the junction/channel temperature.
- 15 October 2023
- Published by Wiley in Advanced Materials
- Vol. 35 (46) , e2301563
Spatially Controlled UV Light Generation at Depth using Upconversion Micelles
UV light can trigger a plethora of useful photochemical reactions for diverse applications, including photocatalysis, photopolymerization, and drug delivery. These applications typically require penetration of high‐energy photons deep into materials, yet delivering these photons beyond the surface is extremely challenging due to absorption and scattering effects. Triplet–triplet annihilation upconversion (TTA‐UC) shows great promise to circumvent this issue by generating high‐energy photons from incident lower‐energy photons. However, molecules that facilitate TTA‐UC usually have poor water solubility, limiting their deployment in aqueous environments. To address this challenge, a nanoencapsulation method is leveraged to fabricate water‐compatible UC micelles, enabling on‐demand UV photon generation deep into materials. Two iridium‐based complexes are presented for use as TTA‐UC sensitizers with increased solubilities that facilitate the formation of highly emissive UV‐upconverting micelles. Furthermore, this encapsulation method is shown to be generalizable to nineteen UV‐emitting UC systems, accessing a range of upconverted UV emission profiles with wavelengths as low as 350 nm. As a proof‐of‐principle demonstration of precision photochemistry at depth, UV‐emitting UC micelles are used to photolyze a fluorophore at a focal point nearly a centimeter beyond the surface, revealing opportunities for spatially controlled manipulation deep into UV‐responsive materials.
- 15 October 2023
- Published by Wiley in Advanced Materials
- Vol. 35 (46) , e2301563
Spatially Controlled UV Light Generation at Depth using Upconversion Micelles
UV light can trigger a plethora of useful photochemical reactions for diverse applications, including photocatalysis, photopolymerization, and drug delivery. These applications typically require penetration of high‐energy photons deep into materials, yet delivering these photons beyond the surface is extremely challenging due to absorption and scattering effects. Triplet–triplet annihilation upconversion (TTA‐UC) shows great promise to circumvent this issue by generating high‐energy photons from incident lower‐energy photons. However, molecules that facilitate TTA‐UC usually have poor water solubility, limiting their deployment in aqueous environments. To address this challenge, a nanoencapsulation method is leveraged to fabricate water‐compatible UC micelles, enabling on‐demand UV photon generation deep into materials. Two iridium‐based complexes are presented for use as TTA‐UC sensitizers with increased solubilities that facilitate the formation of highly emissive UV‐upconverting micelles. Furthermore, this encapsulation method is shown to be generalizable to nineteen UV‐emitting UC systems, accessing a range of upconverted UV emission profiles with wavelengths as low as 350 nm. As a proof‐of‐principle demonstration of precision photochemistry at depth, UV‐emitting UC micelles are used to photolyze a fluorophore at a focal point nearly a centimeter beyond the surface, revealing opportunities for spatially controlled manipulation deep into UV‐responsive materials.
- 11 November 2021
- Published by Wiley in Magnetic Resonance in Chemistry
- Vol. 60 (3) , 398-406
Theoretical studies of the concentration dependences of d–d transition band, g factors, and local distortion for V4+ in Li2O–PbO–B2O3–P2O5 glasses
In this work, the g factors, d–d transition band, local distortion, and their concentration dependences for impurity V4+ in 20Li2O–20PbO–45B2O3–(15 − x)P2O5:V2O5 (0 ≤ x ≤ 2.5 mol%) glasses are theoretically investigated by using perturbation formulas of g factors for a tetragonally compressed octahedral 3d1 cluster. In the light of the cubic polynomial concentration functions for cubic field parameter Dq, covalency factor N, and relative tetragonal compression ratio ρ, the calculated concentration dependences of d–d transition band and g factors for V4+ show good agreement with the experimental data. With increasing x, N (≈0.7682–0.8165) displays the monotonously increasing trend, whereas ρ (≈6.5–4.2%) and Dq (≈1504.9–1481.1 cm−1) exhibit the decreasing tendencies. The above concentration dependences can be ascribed to the modifications of the V4+–O2− bonding and orbital admixtures around the impurity V4+ due to the effects of V2O5 doping on the stability of the glass network, the strength of local crystal fields, and the electron cloud distribution.
- 11 November 2021
- Published by Wiley in Magnetic Resonance in Chemistry
- Vol. 60 (3) , 398-406
Theoretical studies of the concentration dependences of d–d transition band, g factors, and local distortion for V4+ in Li2O–PbO–B2O3–P2O5 glasses
In this work, the g factors, d–d transition band, local distortion, and their concentration dependences for impurity V4+ in 20Li2O–20PbO–45B2O3–(15 − x)P2O5:V2O5 (0 ≤ x ≤ 2.5 mol%) glasses are theoretically investigated by using perturbation formulas of g factors for a tetragonally compressed octahedral 3d1 cluster. In the light of the cubic polynomial concentration functions for cubic field parameter Dq, covalency factor N, and relative tetragonal compression ratio ρ, the calculated concentration dependences of d–d transition band and g factors for V4+ show good agreement with the experimental data. With increasing x, N (≈0.7682–0.8165) displays the monotonously increasing trend, whereas ρ (≈6.5–4.2%) and Dq (≈1504.9–1481.1 cm−1) exhibit the decreasing tendencies. The above concentration dependences can be ascribed to the modifications of the V4+–O2− bonding and orbital admixtures around the impurity V4+ due to the effects of V2O5 doping on the stability of the glass network, the strength of local crystal fields, and the electron cloud distribution.