Pedro P. Fonseca
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Pedro P. Fonseca has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Valdemar R. Duarte
4 shared publicationsCarla M. Machado
Department of Mechanical and Industrial Engineering, UNIDEMI, NOVA School of Science and Technology, NOVA University Lisbon, Caparica, Portugal
3 shared publicationsTelmo G. Santos
3 shared publicationsFrancisco Ferreira
Department of Mechanical and Industrial Engineering, UNIDEMI, NOVA School of Science and Technology, NOVA University Lisbon, Caparica, Portugal
2 shared publicationsTiago A. Rodrigues
Department of Mechanical and Industrial Engineering, UNIDEMI, NOVA School of Science and Technology, NOVA University Lisbon, Caparica, Portugal
2 shared publicationsTiago Silva
2 shared publications
Latest Publications
- Open Access
- 25 September 2025
- Published by Elsevier in Measurement
- Vol. 258
In-situ assessment of machinability and chip formation through the dynamic contact electrical resistance measurement method (DyCERM)
- 25 September 2025
- Published by Elsevier in Measurement
- Vol. 258
Open AccessIn-situ assessment of machinability and chip formation through the dynamic contact electrical resistance measurement method (DyCERM)
- Open Access
- 27 September 2024
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 10 (5) , 3417-3436
Enhancing manufacturing and post-processing properties of WAAM ER110 HSLA steel: in situ hot forging + post-deposited heat treatment effects on surface quality and specific cutting energy
This work focuses on the influence of post-deposited heat treatments (PDHT) on the properties and machinability of high-strength low-alloy steel (HSLA) samples, produced by WAAM and the forged (HF-WAAM) variant. An adequate combination of deposition parameters was established, and the manufactured specimens were 3D scanned to evaluate the surface quality. Effects of normalizing and quenching & tempering (Q&T) heat treatments on the microstructure were assessed through optical microscopy and SEM, and the influence on the material hardness and electrical conductivity was evaluated. Orthogonal cutting experiments were conducted to determine the specific cutting energy (SCE), a crucial indicator of the cutting performance and machinability characteristics of the work material. The results revealed a significant SCE decrease when cutting the WAAM and HF-WAAM samples subjected to PDHT, with 8% and 38% decreases for pot-normalization, and 22% and 27% reductions after Q&T, compared to the as-built condition. No significant differences were registered when machining between the WAAM and HF-WAAM variants. HF-WAAM samples after PDHT show superior hardness, without compromising the cutting energy consumption. However, the geometrical features, namely the significant increase of the surface waviness of the hot-forged parts (≈70%) must be considered, being a critical factor to avoid possible undesirable machining effects.
- 27 September 2024
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 10 (5) , 3417-3436
Open AccessEnhancing manufacturing and post-processing properties of WAAM ER110 HSLA steel: in situ hot forging + post-deposited heat treatment effects on surface quality and specific cutting energy
This work focuses on the influence of post-deposited heat treatments (PDHT) on the properties and machinability of high-strength low-alloy steel (HSLA) samples, produced by WAAM and the forged (HF-WAAM) variant. An adequate combination of deposition parameters was established, and the manufactured specimens were 3D scanned to evaluate the surface quality. Effects of normalizing and quenching & tempering (Q&T) heat treatments on the microstructure were assessed through optical microscopy and SEM, and the influence on the material hardness and electrical conductivity was evaluated. Orthogonal cutting experiments were conducted to determine the specific cutting energy (SCE), a crucial indicator of the cutting performance and machinability characteristics of the work material. The results revealed a significant SCE decrease when cutting the WAAM and HF-WAAM samples subjected to PDHT, with 8% and 38% decreases for pot-normalization, and 22% and 27% reductions after Q&T, compared to the as-built condition. No significant differences were registered when machining between the WAAM and HF-WAAM variants. HF-WAAM samples after PDHT show superior hardness, without compromising the cutting energy consumption. However, the geometrical features, namely the significant increase of the surface waviness of the hot-forged parts (≈70%) must be considered, being a critical factor to avoid possible undesirable machining effects.
- 12 January 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 119 (7-8) , 4439-4459
Orthogonal cutting of Wire and Arc Additive Manufactured parts
- 12 January 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 119 (7-8) , 4439-4459
Orthogonal cutting of Wire and Arc Additive Manufactured parts
- Open Access
- 8 November 2021
- Published by Springer Nature in Research Square
Orthogonal Cutting of Wire and Arc Additive Manufactured Parts
Wire and Arc Additive Manufacturing (WAAM) is increasingly being used to produce complex and non-traditional geometries that other technologies are not able to create. Finishing operations, as machining, are often required to accomplish the components functionality. However, recent studies suggest that several machining issues arise due to the lack of geometrical tolerances and complex shapes of the manufactured parts, like chattering effects, appropriate work holding selection and component alignment. This work aimed to evaluate if the established scientific knowledge for machining homogeneous and isotropic materials remains valid for machining WAAM parts. Two different variants of WAAM were analysed, namely, conventional MIG/MAG and hot forging (HF-WAAM). The cutting operations were carried out varying the undeformed chip thickness (UCT) and the cutting speed, using a tool rake angle of 25°. A systematic comparison was conducted between the existing theoretical principles and the obtained practical results of the orthogonal cutting process, where material properties (hardness, grain size, yield strength) and important machining outcomes (cutting forces, specific cutting energy, friction, shear stress, chip formation and surface roughness) are addressed. Additionally, high-speed camera records were used to evaluate the generated shear angle and chip formation process during the experimental tests. The machinability indicators shown that, through the appropriate cutting parameters, machining forces and energy consumption can be reduced up to 12%, when machining the mechanical improved HF-WAAM material, without compromising the surface quality requirements.
- 8 November 2021
- Published by Springer Nature in Research Square
Open AccessOrthogonal Cutting of Wire and Arc Additive Manufactured Parts
Wire and Arc Additive Manufacturing (WAAM) is increasingly being used to produce complex and non-traditional geometries that other technologies are not able to create. Finishing operations, as machining, are often required to accomplish the components functionality. However, recent studies suggest that several machining issues arise due to the lack of geometrical tolerances and complex shapes of the manufactured parts, like chattering effects, appropriate work holding selection and component alignment. This work aimed to evaluate if the established scientific knowledge for machining homogeneous and isotropic materials remains valid for machining WAAM parts. Two different variants of WAAM were analysed, namely, conventional MIG/MAG and hot forging (HF-WAAM). The cutting operations were carried out varying the undeformed chip thickness (UCT) and the cutting speed, using a tool rake angle of 25°. A systematic comparison was conducted between the existing theoretical principles and the obtained practical results of the orthogonal cutting process, where material properties (hardness, grain size, yield strength) and important machining outcomes (cutting forces, specific cutting energy, friction, shear stress, chip formation and surface roughness) are addressed. Additionally, high-speed camera records were used to evaluate the generated shear angle and chip formation process during the experimental tests. The machinability indicators shown that, through the appropriate cutting parameters, machining forces and energy consumption can be reduced up to 12%, when machining the mechanical improved HF-WAAM material, without compromising the surface quality requirements.