Chunliang Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Chunliang Yang has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Fei Liu
Guizhou University
3 shared publications - Jun Ma
Department of Chemical Engineering, School of Chemistry and Chemical Engineering, Guizhou University, Guiyang 550025, China
2 shared publications - Lin Fu
School of Chemistry and Chemical Engineering, Guizhou University, Guiyang, Guizhou 550025, China
2 shared publications - Mengqin Yao
Department of Chemical Engineering, School of Chemistry and Chemical Engineering
2 shared publications - Aihong Xu
Department of Chemical Engineering, School of Chemistry and Chemical Engineering, Guizhou University, Guiyang 550025, China
1 shared publication Changqun Cen
School of Chemistry and Chemical Engineering, Guizhou University, Guiyang, China
1 shared publication
Latest Publications
- 26 September 2024
- Published by Wiley in Energy Technology
- Vol. 13 (1)
Red‐Phosphorus‐Based Anode Materials for Sodium‐Ion Batteries: Challenges and Progress
The shortage of lithium resources is widely recognized as a key factor that affects the further development of lithium‐ion batteries (LIBs). The sodium (Na) has abundant resources in the earth's crust and its physicochemical properties are similar to Li, which ensure that sodium‐ion batteries (SIBs) are considered as a substitute for LIBs in certain fields. Unfortunately, the lower energy density of SIBs limits its application range. Therefore, studying high specific capacity anode materials to improve the energy density of batteries is an important direction of SIBs. Red‐phosphorus (P)‐based anode materials are ideal candidates for high energy density SIBs because of their high theoretical specific capacity and suitable working voltage. However, the red‐P‐based anode materials for SIBs meet intractable challenges in terms of the poor electrical conductivity and huge volume changes during cycling, resulting in inferior electrochemical performances. In this article, the research progress of red‐P‐based anode material for SIBs in recent years, including the red‐P/carbon composite, element‐doped composite, metal phosphide, and stable interface design, is reviewed. Herein, the decisive role is highlighted that composite design with highly conductive carbon materials plays in addressing the challenges associated with red‐P‐based anodes and a perspective on their development direction is given.
- 26 September 2024
- Published by Wiley in Energy Technology
- Vol. 13 (1)
Red‐Phosphorus‐Based Anode Materials for Sodium‐Ion Batteries: Challenges and Progress
The shortage of lithium resources is widely recognized as a key factor that affects the further development of lithium‐ion batteries (LIBs). The sodium (Na) has abundant resources in the earth's crust and its physicochemical properties are similar to Li, which ensure that sodium‐ion batteries (SIBs) are considered as a substitute for LIBs in certain fields. Unfortunately, the lower energy density of SIBs limits its application range. Therefore, studying high specific capacity anode materials to improve the energy density of batteries is an important direction of SIBs. Red‐phosphorus (P)‐based anode materials are ideal candidates for high energy density SIBs because of their high theoretical specific capacity and suitable working voltage. However, the red‐P‐based anode materials for SIBs meet intractable challenges in terms of the poor electrical conductivity and huge volume changes during cycling, resulting in inferior electrochemical performances. In this article, the research progress of red‐P‐based anode material for SIBs in recent years, including the red‐P/carbon composite, element‐doped composite, metal phosphide, and stable interface design, is reviewed. Herein, the decisive role is highlighted that composite design with highly conductive carbon materials plays in addressing the challenges associated with red‐P‐based anodes and a perspective on their development direction is given.
- 14 December 2023
- Published by Springer Nature in Journal of Materials Science
- Vol. 59 (1) , 206-214
Graphene-strengthened ternary Sn-based sulfide as advanced lithium storage material
- 14 December 2023
- Published by Springer Nature in Journal of Materials Science
- Vol. 59 (1) , 206-214
Graphene-strengthened ternary Sn-based sulfide as advanced lithium storage material
- Open Access
- 16 June 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (12) , 2082
Electrochemical Properties of an Sn-Doped LATP Ceramic Electrolyte and Its Derived Sandwich-Structured Composite Solid Electrolyte
An Li1.3Al0.3SnxTi1.7−x(PO4)3 (LATP-xSn) ceramic solid electrolyte was prepared by Sn doping via a solid phase method. The results showed that adding an Sn dopant with a larger ionic radius in a concentration of x = 0.35 enabled one to equivalently substitute Ti sites in the LATP crystal structure to the maximum extent. The uniform Sn doping could produce a stable LATP structure with small grain size and improved relative density. The lattice distortion induced by Sn doping also modified the transport channels of Li ions, which promoted the increase of ionic conductivity from 5.05 × 10−5 to 4.71 × 10−4 S/cm at room temperature. The SPE/LATP-0.35Sn/SPE composite solid electrolyte with a sandwich structure was prepared by coating, which had a high ionic conductivity of 5.9 × 10−5 S/cm at room temperature, a wide electrochemical window of 4.66 V vs. Li/Li+, and a good lithium-ion migration number of 0.38. The Li||Li symmetric battery test results revealed that the composite solid electrolyte could stably perform for 500 h at 60 °C under the current density of 0.2 mA/cm2, indicating its good interface stability with metallic lithium. Moreover, the analysis of the all-solid-state LiFePO4||SPE/LATP-0.35Sn/SPE||Li battery showed that the composite solid electrolyte had good cycling stability and rate performance. Under the conditions of 60 °C and 0.2 C, stable accumulation up to 200 cycles was achieved at a capacity retention ratio of 90.5% and a coulombic efficiency of about 100% after cycling test.
- 16 June 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (12) , 2082
Open AccessElectrochemical Properties of an Sn-Doped LATP Ceramic Electrolyte and Its Derived Sandwich-Structured Composite Solid Electrolyte
An Li1.3Al0.3SnxTi1.7−x(PO4)3 (LATP-xSn) ceramic solid electrolyte was prepared by Sn doping via a solid phase method. The results showed that adding an Sn dopant with a larger ionic radius in a concentration of x = 0.35 enabled one to equivalently substitute Ti sites in the LATP crystal structure to the maximum extent. The uniform Sn doping could produce a stable LATP structure with small grain size and improved relative density. The lattice distortion induced by Sn doping also modified the transport channels of Li ions, which promoted the increase of ionic conductivity from 5.05 × 10−5 to 4.71 × 10−4 S/cm at room temperature. The SPE/LATP-0.35Sn/SPE composite solid electrolyte with a sandwich structure was prepared by coating, which had a high ionic conductivity of 5.9 × 10−5 S/cm at room temperature, a wide electrochemical window of 4.66 V vs. Li/Li+, and a good lithium-ion migration number of 0.38. The Li||Li symmetric battery test results revealed that the composite solid electrolyte could stably perform for 500 h at 60 °C under the current density of 0.2 mA/cm2, indicating its good interface stability with metallic lithium. Moreover, the analysis of the all-solid-state LiFePO4||SPE/LATP-0.35Sn/SPE||Li battery showed that the composite solid electrolyte had good cycling stability and rate performance. Under the conditions of 60 °C and 0.2 C, stable accumulation up to 200 cycles was achieved at a capacity retention ratio of 90.5% and a coulombic efficiency of about 100% after cycling test.
- Open Access
- 11 November 2021
- Published by MDPI AG in Nanomaterials
- Vol. 11 (11) , 3028
Facile Synthesis of Microporous Carbons from Biomass Waste as High Performance Supports for Dehydrogenation of Formic Acid
Formic acid (FA) is found to be a potential candidate for the storage of hydrogen. For dehydrogenation of FA, the supports of our catalysts were acquired by conducting ZnCl2 treatment and carbonation for biomass waste. The texture and surface properties significantly affected the size and dispersion of Pd and its interaction with the support so as to cause the superior catalytic performance of catalysts. Microporous carbon obtained by carbonization of ZnCl2 activated peanut shells (CPS-ZnCl2) possessing surface areas of 629 m2·g−1 and a micropore rate of 73.5%. For ZnCl2 activated melon seed (CMS-ZnCl2), the surface area and micropore rate increased to 1081 m2·g−1 and 80.0%, respectively. In addition, the introduction of ZnCl2 also caused the increase in surface O content and reduced the acidity of the catalyst. The results represented that CMS-ZnCl2 with uniform honeycomb morphology displayed the best properties, and the as-prepared Pd/CMS-ZnCl2 catalyst afforded 100% hydrogen selectivity as well as excellent catalytic activity with an initial high turnover number (TON) value of 28.3 at 30 °C and 100.1 at 60 °C.
- 11 November 2021
- Published by MDPI AG in Nanomaterials
- Vol. 11 (11) , 3028
Open AccessFacile Synthesis of Microporous Carbons from Biomass Waste as High Performance Supports for Dehydrogenation of Formic Acid
Formic acid (FA) is found to be a potential candidate for the storage of hydrogen. For dehydrogenation of FA, the supports of our catalysts were acquired by conducting ZnCl2 treatment and carbonation for biomass waste. The texture and surface properties significantly affected the size and dispersion of Pd and its interaction with the support so as to cause the superior catalytic performance of catalysts. Microporous carbon obtained by carbonization of ZnCl2 activated peanut shells (CPS-ZnCl2) possessing surface areas of 629 m2·g−1 and a micropore rate of 73.5%. For ZnCl2 activated melon seed (CMS-ZnCl2), the surface area and micropore rate increased to 1081 m2·g−1 and 80.0%, respectively. In addition, the introduction of ZnCl2 also caused the increase in surface O content and reduced the acidity of the catalyst. The results represented that CMS-ZnCl2 with uniform honeycomb morphology displayed the best properties, and the as-prepared Pd/CMS-ZnCl2 catalyst afforded 100% hydrogen selectivity as well as excellent catalytic activity with an initial high turnover number (TON) value of 28.3 at 30 °C and 100.1 at 60 °C.