Sungmin Yoon
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Sungmin Yoon has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
- Shaojie Gu
Magnesium Research Center, Kumamoto University, Kumamoto 860-8555, Japan
10 shared publications - Yuhki Toku
Department of Micro-Nano Mechanical Science and Engineering, Graduate School of Engineering, Nagoya University, Nagoya 464-8601, Japan
10 shared publications Yang Ju
7 shared publicationsYasuhiro Kimura
6 shared publications- Yasuhiro Kimura
Department of Mechanical Engineering, Kyushu University, Fukuoka 819-0395, Japan
5 shared publications - Yang Ju
State Key Laboratory of Fluid Power and Mechatronic Systems, School of Mechanical Engineering, Zhejiang University, Hangzhou, China
4 shared publications
Latest Publications
- Open Access
- 19 June 2026
- Published by Elsevier in Results in Engineering
- Vol. 31
Effect of graphite nanoplatelet content on the friction and wear properties of basalt fiber-reinforced polymer composites
- 19 June 2026
- Published by Elsevier in Results in Engineering
- Vol. 31
Open AccessEffect of graphite nanoplatelet content on the friction and wear properties of basalt fiber-reinforced polymer composites
- Open Access
- 4 June 2026
- Published by Elsevier in SSRN Electronic Journal
Friction and Wear Behavior of MoS2 Reinforced AlCoCrFeNi High–Entropy Alloy Composite
This study developed a bulk self–lubricating material that simultaneously suppresses friction and wear by sintering together a MoS2, transition metal di–chalcogenide solid lubricant, and an AlCoCrFeNi high–entropy alloy. In this study, bulk AlCoCrFeNi–MoS2 composites were fabricated by spark plasma sintering of AlCoCrFeNi powders synthesized via self–propagating high–temperature synthesis (SHS) and adding 0–20 wt% MoS2 powder. The resulting matrix exhibited a predominantly body-centered cubic (BCC) (A2, B2) phase with a thin interstitial face-centered cubic (FCC) phase. MoS2 was distributed primarily at grain boundaries in a continuous and intermittent network, as intended. The friction behavior was evaluated under reciprocating sliding conditions. As the MoS2 content increased, the average friction coefficient decreased by approximately 30%. The wear track width, maximum depth, and cross–sectional area evaluated by confocal microscopy all decreased monotonically with the MoS2 content. These trends are consistent with the scanning electron microscopy (SEM) fractography and energy dispersive spectroscopy (EDX) mapping, which reveal broad in-track Mo and S co-localization and the formation of a lubricious tribo-film. With increasing MoS2, the dominant wear mechanism transitions from adhesive to abrasive and ultimately to film-dominated sliding, providing mechanistic support for the observed reductions in friction and wear. To our knowledge, this is the first report of successful synthesis of bulk AlCoCrFeNi using SHS technique, and the tribological properties of the bulk self–lubricating materials, AlCoCrFeNi – MoS2 composites were evaluated.
- 4 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessFriction and Wear Behavior of MoS2 Reinforced AlCoCrFeNi High–Entropy Alloy Composite
This study developed a bulk self–lubricating material that simultaneously suppresses friction and wear by sintering together a MoS2, transition metal di–chalcogenide solid lubricant, and an AlCoCrFeNi high–entropy alloy. In this study, bulk AlCoCrFeNi–MoS2 composites were fabricated by spark plasma sintering of AlCoCrFeNi powders synthesized via self–propagating high–temperature synthesis (SHS) and adding 0–20 wt% MoS2 powder. The resulting matrix exhibited a predominantly body-centered cubic (BCC) (A2, B2) phase with a thin interstitial face-centered cubic (FCC) phase. MoS2 was distributed primarily at grain boundaries in a continuous and intermittent network, as intended. The friction behavior was evaluated under reciprocating sliding conditions. As the MoS2 content increased, the average friction coefficient decreased by approximately 30%. The wear track width, maximum depth, and cross–sectional area evaluated by confocal microscopy all decreased monotonically with the MoS2 content. These trends are consistent with the scanning electron microscopy (SEM) fractography and energy dispersive spectroscopy (EDX) mapping, which reveal broad in-track Mo and S co-localization and the formation of a lubricious tribo-film. With increasing MoS2, the dominant wear mechanism transitions from adhesive to abrasive and ultimately to film-dominated sliding, providing mechanistic support for the observed reductions in friction and wear. To our knowledge, this is the first report of successful synthesis of bulk AlCoCrFeNi using SHS technique, and the tribological properties of the bulk self–lubricating materials, AlCoCrFeNi – MoS2 composites were evaluated.
- Open Access
- 29 May 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (6) , 189
Thermal and Athermal Effects of High-Density Pulsed Electric Current on Strain-Hardening Relief in Cold-Rolled A6061 Under Liquid Nitrogen
Understanding the respective roles of thermal and athermal effects during electric current treatment is critical for advancing current-assisted processing of metallic materials. In this study, strain hardening in cold-rolled A6061 was effectively relieved using high-density pulsed electric current. By conducting comparative experiments under room-temperature and liquid-nitrogen conditions, the thermal and athermal contributions were quantitatively evaluated. The results indicate that thermal effects dominate over athermal effects in dislocation density reduction and strain-hardening relief. Nevertheless, the athermal effect, driven by electron wind force, is capable of promoting dislocation motion and annihilation. This work provides a practical framework for evaluating thermal and athermal contributions and offers new insights into microstructure control via electric current, with implications for the design of advanced structural materials.
- 29 May 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (6) , 189
Open AccessThermal and Athermal Effects of High-Density Pulsed Electric Current on Strain-Hardening Relief in Cold-Rolled A6061 Under Liquid Nitrogen
Understanding the respective roles of thermal and athermal effects during electric current treatment is critical for advancing current-assisted processing of metallic materials. In this study, strain hardening in cold-rolled A6061 was effectively relieved using high-density pulsed electric current. By conducting comparative experiments under room-temperature and liquid-nitrogen conditions, the thermal and athermal contributions were quantitatively evaluated. The results indicate that thermal effects dominate over athermal effects in dislocation density reduction and strain-hardening relief. Nevertheless, the athermal effect, driven by electron wind force, is capable of promoting dislocation motion and annihilation. This work provides a practical framework for evaluating thermal and athermal contributions and offers new insights into microstructure control via electric current, with implications for the design of advanced structural materials.
- 31 October 2025
- Published by World Scientific Pub Co Pte Ltd in Modern Physics Letters B
- Vol. 40 (02)
Closed-form physics-informed extension of Griffith’s law for HDPEC-retarded crack growth
Crack propagation in metallic alloys remains a central challenge in structural integrity assessment. Conventional models based on linear elasticity or idealized plastic-zone theories do not adequately reflect the toughening mechanisms introduced by electropulsing. This study presents a closed-form analytical extension of Griffith’s law that incorporates a three-coefficient damping term to capture the current-induced plastic dissipation near the crack tip. The proposed model accurately reproduces the full stress-crack-length response under electropulsing conditions up to 400[ ]A/mm 2 with sub-3% error using only 8–10 data points. Validation through in-situ optical tracking and multiscale scanning electron microscopy confirms a smooth transition from elastic to plastic crack growth that depends on current density. The damping coefficient [ ] increases dramatically from 0.01 to 0.77 with pulse intensity and correlates directly with microstructural evidence of crack tip blunting and void coalescence. This physics-based formulation bridges fundamental electromagnetic effects with practical fracture assessment, enabling predictive design of fracture-critical components under combined mechanical and electrical loading.
- 31 October 2025
- Published by World Scientific Pub Co Pte Ltd in Modern Physics Letters B
- Vol. 40 (02)
Closed-form physics-informed extension of Griffith’s law for HDPEC-retarded crack growth
Crack propagation in metallic alloys remains a central challenge in structural integrity assessment. Conventional models based on linear elasticity or idealized plastic-zone theories do not adequately reflect the toughening mechanisms introduced by electropulsing. This study presents a closed-form analytical extension of Griffith’s law that incorporates a three-coefficient damping term to capture the current-induced plastic dissipation near the crack tip. The proposed model accurately reproduces the full stress-crack-length response under electropulsing conditions up to 400[ ]A/mm 2 with sub-3% error using only 8–10 data points. Validation through in-situ optical tracking and multiscale scanning electron microscopy confirms a smooth transition from elastic to plastic crack growth that depends on current density. The damping coefficient [ ] increases dramatically from 0.01 to 0.77 with pulse intensity and correlates directly with microstructural evidence of crack tip blunting and void coalescence. This physics-based formulation bridges fundamental electromagnetic effects with practical fracture assessment, enabling predictive design of fracture-critical components under combined mechanical and electrical loading.
- Open Access
- 15 July 2025
- Published by Elsevier in International Journal of Fatigue
- Vol. 201
Electric current-induced crack healing: mechanisms and scale-specific insights
- 15 July 2025
- Published by Elsevier in International Journal of Fatigue
- Vol. 201
Open AccessElectric current-induced crack healing: mechanisms and scale-specific insights
- Open Access
- 12 May 2025
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 15 (20) , 15781-15795
Fatigue life predictor: predicting fatigue life of metallic material using LSTM with a contextual attention model
Low-cycle fatigue (LCF) data involve complex temporal interactions in a strain cycle series, which hinders accurate fatigue life prediction. Current studies lack reliable methods for fatigue life prediction using only initial-cycle data while simultaneously capturing both temporal dependencies and localized features. This study introduces a novel deep-learning-based prediction model designed for LCF data. The proposed approach combines long short-term memory (LSTM) and convolutional neural network (CNN) architectures with an attention mechanism to effectively capture the temporal and localized characteristics of stress–strain data from acquisition through a series of cycle strain-controlled tests. Among the models tested, the LSTM-contextual attention model demonstrated superior performance (R2 = 0.99), outperforming the baseline LSTM and CNN models with higher R2 values and improved statistical metrics. The analysis of attention weights further revealed the model's ability to focus on critical timesteps associated with fatigue damage, highlighting its effectiveness in learning key features from LCF data. This study underscores the potential of deep-learning-based methods for accurate fatigue life prediction in LCF applications. This study provides a foundation for future research to extend these approaches to diverse materials with varying fatigue conditions and advanced models capable of incorporating non-linear fatigue mechanisms.
- 12 May 2025
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 15 (20) , 15781-15795
Open AccessFatigue life predictor: predicting fatigue life of metallic material using LSTM with a contextual attention model
Low-cycle fatigue (LCF) data involve complex temporal interactions in a strain cycle series, which hinders accurate fatigue life prediction. Current studies lack reliable methods for fatigue life prediction using only initial-cycle data while simultaneously capturing both temporal dependencies and localized features. This study introduces a novel deep-learning-based prediction model designed for LCF data. The proposed approach combines long short-term memory (LSTM) and convolutional neural network (CNN) architectures with an attention mechanism to effectively capture the temporal and localized characteristics of stress–strain data from acquisition through a series of cycle strain-controlled tests. Among the models tested, the LSTM-contextual attention model demonstrated superior performance (R2 = 0.99), outperforming the baseline LSTM and CNN models with higher R2 values and improved statistical metrics. The analysis of attention weights further revealed the model's ability to focus on critical timesteps associated with fatigue damage, highlighting its effectiveness in learning key features from LCF data. This study underscores the potential of deep-learning-based methods for accurate fatigue life prediction in LCF applications. This study provides a foundation for future research to extend these approaches to diverse materials with varying fatigue conditions and advanced models capable of incorporating non-linear fatigue mechanisms.
- Open Access
- 25 November 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (1)
Restoring Plasticity in Nickel‐Based Superalloy Using High‐Density Pulsed Electric Current
This study explores the efficacy of high‐density pulsed electric current (HDPEC) in healing plastic deformation damage in single‐crystal Ni‐based superalloys. Single‐crystal specimens are prepared from directionally solidified nickel‐based superalloy to assess the potential of electric current treatment in restoring plastic deformation capability. Experiments involving various current densities and pulse durations reveal that a pulsed electric current of 17 ms at 400 A mm−2 yields optimal results, enhancing fracture elongation from 7.8% to 12.3% without compromising strength. The study conducts a comprehensive analysis of microstructural changes induced by pulsed electric current, employing quasi‐in‐situ electron backscatter diffraction and transmission electron microscopy techniques. The results demonstrate that HDPEC disrupts the planar dislocation network, homogenizes dislocation distribution, and promotes dislocation entanglement. Consequently, microdefects in the alloy are eliminated, restoring the material's ductility. The findings suggest that this technology holds significant promise for repairing fatigued components and underscore the potential for further research in this domain.
- 25 November 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (1)
Open AccessRestoring Plasticity in Nickel‐Based Superalloy Using High‐Density Pulsed Electric Current
This study explores the efficacy of high‐density pulsed electric current (HDPEC) in healing plastic deformation damage in single‐crystal Ni‐based superalloys. Single‐crystal specimens are prepared from directionally solidified nickel‐based superalloy to assess the potential of electric current treatment in restoring plastic deformation capability. Experiments involving various current densities and pulse durations reveal that a pulsed electric current of 17 ms at 400 A mm−2 yields optimal results, enhancing fracture elongation from 7.8% to 12.3% without compromising strength. The study conducts a comprehensive analysis of microstructural changes induced by pulsed electric current, employing quasi‐in‐situ electron backscatter diffraction and transmission electron microscopy techniques. The results demonstrate that HDPEC disrupts the planar dislocation network, homogenizes dislocation distribution, and promotes dislocation entanglement. Consequently, microdefects in the alloy are eliminated, restoring the material's ductility. The findings suggest that this technology holds significant promise for repairing fatigued components and underscore the potential for further research in this domain.