Moe Moe Aye
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Moe Moe Aye has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Hannu Huhtinen
University of Turku
12 shared publications - Petriina Paturi
University of Turku
12 shared publications - Elmeri Rivasto
University of Southern Denmark
9 shared publications - Hannes Rijckaert
Ghent University
6 shared publications Hannu Huhtinen
Wihuri Physical Laboratory, Department of Physics and Astronomy, University of Turku, 20014 Turku, Finland
4 shared publications- Isabel Van Driessche
Ghent University
4 shared publications
Latest Publications
- Open Access
- 1 September 2026
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 39 (9) , 095020
Towards optimal BZO nanorod distribution in YBCO/Ca-YBCO multilayers
BaZrO 3 (BZO) nanorod-doped YBa 2 Cu 3 O 6 + x (YBCO) thin films with single-layer and multilayer architectures were fabricated to investigate the combined effects of artificial pinning centres and multilayering on flux pinning and critical current performance. Structural analyses show that Ca-doped YBCO interlayers improve crystalline quality and promote the growth of straighter, more uniformly distributed BZO nanorods. As a result, multilayer films exhibit superior in-field performance at 10 K in magnetic fields ranging from 0 T to 7 T, with the 6 wt.% BZO multilayer showing a J c enhancement of 30%–40 % compared with the corresponding single-layer film and up to 500 % relative to undoped YBCO at 10 K in 7 T field. Angular-dependent transport measurements at 70 K reveal improved isotropy of J c , while comparison with vortex-dynamics simulations indicates that the Ca-doped YBCO interlayers effectively reset nanorod growth between adjacent layers, eliminating lateral spatial correlations. These results demonstrate that BZO-doped multilayer YBCO architectures provide an effective route towards next-generation coated conductors for high-field superconducting applications.
- 1 September 2026
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 39 (9) , 095020
Open AccessTowards optimal BZO nanorod distribution in YBCO/Ca-YBCO multilayers
BaZrO 3 (BZO) nanorod-doped YBa 2 Cu 3 O 6 + x (YBCO) thin films with single-layer and multilayer architectures were fabricated to investigate the combined effects of artificial pinning centres and multilayering on flux pinning and critical current performance. Structural analyses show that Ca-doped YBCO interlayers improve crystalline quality and promote the growth of straighter, more uniformly distributed BZO nanorods. As a result, multilayer films exhibit superior in-field performance at 10 K in magnetic fields ranging from 0 T to 7 T, with the 6 wt.% BZO multilayer showing a J c enhancement of 30%–40 % compared with the corresponding single-layer film and up to 500 % relative to undoped YBCO at 10 K in 7 T field. Angular-dependent transport measurements at 70 K reveal improved isotropy of J c , while comparison with vortex-dynamics simulations indicates that the Ca-doped YBCO interlayers effectively reset nanorod growth between adjacent layers, eliminating lateral spatial correlations. These results demonstrate that BZO-doped multilayer YBCO architectures provide an effective route towards next-generation coated conductors for high-field superconducting applications.
- Open Access
- 23 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Influence of Rare-Earth Variations on the Superconducting Properties of YBCO Films With and Without Artificial Pinning Centers
Thin films of Y1−xGdxBa2Cu3O7−δ (x = 0, 1/3, 1/2, 2/3, 1), with and without BaZrO3 (BZO) artificial pinning centers (APCs), were deposited by pulsed laser deposition (PLD) under growth parameters identical to those used for YBa2Cu3O7−δ. The effects of partial Gd substitution on the critical current density Jc were systematically investigated and the results were found to differ between APC-free and BZO-doped films. Partial substitution of Y by Gd significantly enhanced Jc, particularly in films containing BZO nanorods. At 10K, the x = 2/3 film with APC showed Jc enhancements up to 45% over the x = 0 film across a wide magnetic field and temperature range. These findings strongly support Gd doping in YBCO as a highly promising route for future applications requiring maximized magnetic-field-dependent critical current densities.
- 23 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Open AccessInfluence of Rare-Earth Variations on the Superconducting Properties of YBCO Films With and Without Artificial Pinning Centers
Thin films of Y1−xGdxBa2Cu3O7−δ (x = 0, 1/3, 1/2, 2/3, 1), with and without BaZrO3 (BZO) artificial pinning centers (APCs), were deposited by pulsed laser deposition (PLD) under growth parameters identical to those used for YBa2Cu3O7−δ. The effects of partial Gd substitution on the critical current density Jc were systematically investigated and the results were found to differ between APC-free and BZO-doped films. Partial substitution of Y by Gd significantly enhanced Jc, particularly in films containing BZO nanorods. At 10K, the x = 2/3 film with APC showed Jc enhancements up to 45% over the x = 0 film across a wide magnetic field and temperature range. These findings strongly support Gd doping in YBCO as a highly promising route for future applications requiring maximized magnetic-field-dependent critical current densities.
- Open Access
- 20 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Balancing Structure and Performance: Optimized BZO Nanorod Doping in Ca-Interlayered YBCO Multilayers
This study demonstrates the enhancement of critical current density over a wide temperature and magnetic field range in BZO-doped YBCO multilayer structures using a Ca doped YBCO intermediate layer. Compared to single-layer BZO doped YBCO films, the Ca-doped interlayer improves crystalline quality and reduces non-uniform strain, particularly at low BZO doping concentrations, and promotes better growth of BZO nanorods. Additionally, multilayering slightly increases YBCO's oxygen content across all BZO concentrations, contributing to a higher critical temperature and zero-field critical current density. Besides of this, multilayering enhances critical current density across the magnetic field range, especially at low fields and high BZO concentrations. However, the highest absolute zero f ield critical current density is achieved in undoped multilayered YBCO, whereas in fields above 2T and up to 50K, the best performance is obtained with 4% BZO-doped YBCO layers separated by Ca-doped interlayers. At around 1T, 2% BZO doping yields the highest critical current density. This paper also explores the possible mechanisms behind these effects, proposing that multilayering BZO-doped YBCO with a crystal structure-balancing interlayer could be key to next-generation YBCO coated conductors for high-temperature superconductor applications. Optimising the BZO concentration is crucial when tailoring YBCO compositions for different operating conditions.
- 20 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Open AccessBalancing Structure and Performance: Optimized BZO Nanorod Doping in Ca-Interlayered YBCO Multilayers
This study demonstrates the enhancement of critical current density over a wide temperature and magnetic field range in BZO-doped YBCO multilayer structures using a Ca doped YBCO intermediate layer. Compared to single-layer BZO doped YBCO films, the Ca-doped interlayer improves crystalline quality and reduces non-uniform strain, particularly at low BZO doping concentrations, and promotes better growth of BZO nanorods. Additionally, multilayering slightly increases YBCO's oxygen content across all BZO concentrations, contributing to a higher critical temperature and zero-field critical current density. Besides of this, multilayering enhances critical current density across the magnetic field range, especially at low fields and high BZO concentrations. However, the highest absolute zero f ield critical current density is achieved in undoped multilayered YBCO, whereas in fields above 2T and up to 50K, the best performance is obtained with 4% BZO-doped YBCO layers separated by Ca-doped interlayers. At around 1T, 2% BZO doping yields the highest critical current density. This paper also explores the possible mechanisms behind these effects, proposing that multilayering BZO-doped YBCO with a crystal structure-balancing interlayer could be key to next-generation YBCO coated conductors for high-temperature superconductor applications. Optimising the BZO concentration is crucial when tailoring YBCO compositions for different operating conditions.
- Open Access
- 1 October 2025
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 38 (10) , 105008
Quench dynamics in bare YBCO thin films with and without artificial pinning centers
In this study, we investigate the differences in the normal zone development between artificial pinning center free (APC-free) and BaZrO3 (BZO)-doped YBa2Cu3O 6 + x (YBCO) thin films deposited on SrTiO3 substrates. Normal zone propagation velocities (NZPV) and minimum quench energies (MQE) were measured over a wide range of temperatures (20–70 K) and magnetic fields (0–8 T) as a function of the percentage of the critical current (% I c ). We found that lower MQE values are required in BZO-doped YBCO to trigger a quench. The most significant differences between APC-free and BZO-doped films in NZPV behavior were observed at high temperature and magnetic field values. Differences in quench characteristics can be attributed to variations in flux pinning mechanisms and current-carrying capabilities arising from the distinct properties of pinning centers. Through detailed analysis, this study enhances the understanding of how flux flow influences normal zone development in different YBCO thin films, providing insights relevant to technological challenges such as stability under high magnetic fields and quench detection in future high-temperature superconductor magnets.
- 1 October 2025
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 38 (10) , 105008
Open AccessQuench dynamics in bare YBCO thin films with and without artificial pinning centers
In this study, we investigate the differences in the normal zone development between artificial pinning center free (APC-free) and BaZrO3 (BZO)-doped YBa2Cu3O 6 + x (YBCO) thin films deposited on SrTiO3 substrates. Normal zone propagation velocities (NZPV) and minimum quench energies (MQE) were measured over a wide range of temperatures (20–70 K) and magnetic fields (0–8 T) as a function of the percentage of the critical current (% I c ). We found that lower MQE values are required in BZO-doped YBCO to trigger a quench. The most significant differences between APC-free and BZO-doped films in NZPV behavior were observed at high temperature and magnetic field values. Differences in quench characteristics can be attributed to variations in flux pinning mechanisms and current-carrying capabilities arising from the distinct properties of pinning centers. Through detailed analysis, this study enhances the understanding of how flux flow influences normal zone development in different YBCO thin films, providing insights relevant to technological challenges such as stability under high magnetic fields and quench detection in future high-temperature superconductor magnets.
- Open Access
- 10 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Verifying Theoretical Models of Flux Pinning Using Heavy Ion Irradiated YBCO Thin Films
We have irradiated YBa$_{2}$Cu$_{3}$O$_{6+x}$ (YBCO) films without artificial pinning sites with Ag$^+$ ions with energies of 75 MeV and 150 MeV and fluences between 2–8$\cdot 10^{11}$ ions/cm$^{2}$ in order to create as controlled nanorod pinning sites as possible. The structural and superconducting properties were determined before and after the irradiation with x-ray diffraction and magnetic measurement. After the irradiation also transport and transmission electron microscopy measurements were made. It was noted that the ion tracks are all parallel to the YBCO$c$-axis of the sample and those done with 150 MeV ions formed continuous 5 nm diameter tracks, whereas with 75 MeV ions, the tracks were not continuous through the sample. The $T_{\mathrm{c}}$ and $J_{\mathrm{c}}$$(0 \mathrm{\,T})$ decreased with the irradiation, but the in-field $J_{\mathrm{c}}$ increased. The maximum increase was obtained with the 150 MeV and 4$\cdot 10^{11}$ ions/cm$^{2}$ sample with continuous rods, where the distance between the rods was closest to the diameter of the rods. Thus, the previous theoretical models predicting optimal pinning when the pinning site diameter is approximately equal to the distance between the pinning sites, are experimentally verified for these very pure samples, with no other external pinning sites.
- 10 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Open AccessVerifying Theoretical Models of Flux Pinning Using Heavy Ion Irradiated YBCO Thin Films
We have irradiated YBa$_{2}$Cu$_{3}$O$_{6+x}$ (YBCO) films without artificial pinning sites with Ag$^+$ ions with energies of 75 MeV and 150 MeV and fluences between 2–8$\cdot 10^{11}$ ions/cm$^{2}$ in order to create as controlled nanorod pinning sites as possible. The structural and superconducting properties were determined before and after the irradiation with x-ray diffraction and magnetic measurement. After the irradiation also transport and transmission electron microscopy measurements were made. It was noted that the ion tracks are all parallel to the YBCO$c$-axis of the sample and those done with 150 MeV ions formed continuous 5 nm diameter tracks, whereas with 75 MeV ions, the tracks were not continuous through the sample. The $T_{\mathrm{c}}$ and $J_{\mathrm{c}}$$(0 \mathrm{\,T})$ decreased with the irradiation, but the in-field $J_{\mathrm{c}}$ increased. The maximum increase was obtained with the 150 MeV and 4$\cdot 10^{11}$ ions/cm$^{2}$ sample with continuous rods, where the distance between the rods was closest to the diameter of the rods. Thus, the previous theoretical models predicting optimal pinning when the pinning site diameter is approximately equal to the distance between the pinning sites, are experimentally verified for these very pure samples, with no other external pinning sites.
- Open Access
- 21 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-6
A Method to Enhance Thickness and Current-Carrying Capacity of BZO-Doped YBCO Multilayers
This study demonstrates a significant enhancement in the in-field critical current density and its isotropy in BZO-doped YBCO multilayer structures, achieved through improvements in the crystalline quality of YBCO, which extend the electron mean free path. The incorporation of undoped YBCO, alongside alternating BZO-doped and Ca-doped YBCO layers, revealed that the Ca-doped intermediate layer positively influenced the interface quality, promoting better growth in the subsequent layers. These improvements also enabled an increase in total film thickness, thereby enhancing the current-carrying capacity. Furthermore, the paper discusses the mechanisms behind these enhancements and presents a model explaining how nanorod pinning centres in different layers affect vortex pinning behavior. These insights offer valuable guidance for designing future YBCO coated conductor structures.
- 21 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-6
Open AccessA Method to Enhance Thickness and Current-Carrying Capacity of BZO-Doped YBCO Multilayers
This study demonstrates a significant enhancement in the in-field critical current density and its isotropy in BZO-doped YBCO multilayer structures, achieved through improvements in the crystalline quality of YBCO, which extend the electron mean free path. The incorporation of undoped YBCO, alongside alternating BZO-doped and Ca-doped YBCO layers, revealed that the Ca-doped intermediate layer positively influenced the interface quality, promoting better growth in the subsequent layers. These improvements also enabled an increase in total film thickness, thereby enhancing the current-carrying capacity. Furthermore, the paper discusses the mechanisms behind these enhancements and presents a model explaining how nanorod pinning centres in different layers affect vortex pinning behavior. These insights offer valuable guidance for designing future YBCO coated conductor structures.
- Open Access
- 1 July 2024
- Published by IOP Publishing in Physica Scripta
- Vol. 99 (8) , 085901
Enhanced current-carrying capability in YBCO coated conductor bilayers for high-field applications
We have investigated the impact of bilayer structures on the critical current density, J c, of YBa2Cu3O6+x (YBCO) coated conductor films, i.e. films grown on buffered metal substrates, under varying temperature and magnetic field conditions. The bilayers consisted of a YBCO layer free of artificial pinning centers and 8 wt% BaZrO3-added (BZO) layer on top, where the thickness percentage of the layers was varied from 0 to 100 %. The results reveal that the bilayer configuration enhances J c at temperatures below 60 K, with a significant improvement in high magnetic fields (5–8 T) and temperatures ≤20 K. The optimal BZO-added layer thickness was found to be approximately 70 %, reaching 80 % at 8 T. Structural examinations indicate improved growth of YBCO and BZO nanorods in the bilayer structure with BZO-added layer thickness ≤80 %. Theoretical model of the bilayer structure considering the layers as two parallel superconductors with different properties was developed. It was found that the model adequately explains all the experimentally observed tendencies, and thus the observed maximum in J c is due to better growth of the BZO-added layer. The study provides valuable insights for designing optimal bilayer structures for diverse applications operating in different temperature and magnetic field regimes.
- 1 July 2024
- Published by IOP Publishing in Physica Scripta
- Vol. 99 (8) , 085901
Open AccessEnhanced current-carrying capability in YBCO coated conductor bilayers for high-field applications
We have investigated the impact of bilayer structures on the critical current density, J c, of YBa2Cu3O6+x (YBCO) coated conductor films, i.e. films grown on buffered metal substrates, under varying temperature and magnetic field conditions. The bilayers consisted of a YBCO layer free of artificial pinning centers and 8 wt% BaZrO3-added (BZO) layer on top, where the thickness percentage of the layers was varied from 0 to 100 %. The results reveal that the bilayer configuration enhances J c at temperatures below 60 K, with a significant improvement in high magnetic fields (5–8 T) and temperatures ≤20 K. The optimal BZO-added layer thickness was found to be approximately 70 %, reaching 80 % at 8 T. Structural examinations indicate improved growth of YBCO and BZO nanorods in the bilayer structure with BZO-added layer thickness ≤80 %. Theoretical model of the bilayer structure considering the layers as two parallel superconductors with different properties was developed. It was found that the model adequately explains all the experimentally observed tendencies, and thus the observed maximum in J c is due to better growth of the BZO-added layer. The study provides valuable insights for designing optimal bilayer structures for diverse applications operating in different temperature and magnetic field regimes.
- 20 May 2024
- Published by American Chemical Society (ACS) in Crystal Growth & Design
- Vol. 24 (11) , 4545-4555
Enhanced Critical Current Density in Heterostructural YBCO/Ca-Doped YBCO Multilayers
- 20 May 2024
- Published by American Chemical Society (ACS) in Crystal Growth & Design
- Vol. 24 (11) , 4545-4555
Enhanced Critical Current Density in Heterostructural YBCO/Ca-Doped YBCO Multilayers
- 28 December 2023
- Published by IOP Publishing in Journal of Physics: Condensed Matter
- Vol. 36 (13) , 135702
Enhanced critical current density in optimized high-temperature superconducting bilayer thin films
The superconducting and structural properties of bilayer thin films based on YBa2Cu3O 7 − x / YBa2Cu3O 7 − x +6%BaZrO3 heterstructures have been studied. In a broad range of magnetic field strengths and temperatures, the optimal bilayer film comprises 30% YBCO at the substrate interface and 70% YBCO+6%BZO on the top. The critical current density measured for the optimal bilayer structure is shown to outperform the corresponding single layer films up to almost 60%. The obtained results are comprehensively discussed in the light of our previously published theoretical framework (Rivasto et al 2023 J. Phys.: Condens. Matter 35 075701:1–10). We conclude that the bilayering provides an efficient and easily applicable way to further increase the performance and applicability of high-temperature superconductors in various applications. Consequently, the bilayer films should be seriously considered as candidates for the upcoming generation of coated conductors.
- 28 December 2023
- Published by IOP Publishing in Journal of Physics: Condensed Matter
- Vol. 36 (13) , 135702
Enhanced critical current density in optimized high-temperature superconducting bilayer thin films
The superconducting and structural properties of bilayer thin films based on YBa2Cu3O 7 − x / YBa2Cu3O 7 − x +6%BaZrO3 heterstructures have been studied. In a broad range of magnetic field strengths and temperatures, the optimal bilayer film comprises 30% YBCO at the substrate interface and 70% YBCO+6%BZO on the top. The critical current density measured for the optimal bilayer structure is shown to outperform the corresponding single layer films up to almost 60%. The obtained results are comprehensively discussed in the light of our previously published theoretical framework (Rivasto et al 2023 J. Phys.: Condens. Matter 35 075701:1–10). We conclude that the bilayering provides an efficient and easily applicable way to further increase the performance and applicability of high-temperature superconductors in various applications. Consequently, the bilayer films should be seriously considered as candidates for the upcoming generation of coated conductors.
- Open Access
- 25 September 2023
- Published by American Chemical Society (ACS) in Crystal Growth & Design
- Vol. 23 (11) , 7971-7981
Controlled BZO Nanorod Growth and Improved Flux Pinning in YBCO Films Grown on Vicinal STO Substrates
- 25 September 2023
- Published by American Chemical Society (ACS) in Crystal Growth & Design
- Vol. 23 (11) , 7971-7981
Open AccessControlled BZO Nanorod Growth and Improved Flux Pinning in YBCO Films Grown on Vicinal STO Substrates