Sudha Malik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sudha Malik has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Kumar Vaibhav Srivastava
IIT Kanpur
3 shared publications - Mondeep Saikia
Queen’s University Belfast
2 shared publications - Abhinav Bhardwaj
Department of Electrical Engineering, Indian Institute of Technology Kanpur, Kanpur, India
1 shared publication - Aditi Sharma
Department of Electrical Engineering, Indian Institute of Technology Kanpur, Kanpur, India
1 shared publication - Ayushi Dhumal
Department of Electrical Engineering, Indian Institute of Technology Kanpur, Kanpur, India
1 shared publication - Kahani Kumari
Department of Electrical Engineering, Indian Institute of Technology, Kanpur, India
1 shared publication
Latest Publications
- Open Access
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- p. 1
Investigation of the Potential of Beam Switching for Reduced RF-EMF Exposure in 5G mmWave Networks
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- p. 1
Open AccessInvestigation of the Potential of Beam Switching for Reduced RF-EMF Exposure in 5G mmWave Networks
- Open Access
- 21 March 2024
- Published by Qeios Ltd
Review of: "Investigations on Input Impedance and Radiation Pattern of a UWB Antenna for Microwave Imaging"
* There are lots of similar studies operating within the same frequency, so I want to see the similarities and differences between this work and similar works. Therefore, the introduction section must be revised accordingly. * The presentation of t...
- 21 March 2024
- Published by Qeios Ltd
Open AccessReview of: "Investigations on Input Impedance and Radiation Pattern of a UWB Antenna for Microwave Imaging"
* There are lots of similar studies operating within the same frequency, so I want to see the similarities and differences between this work and similar works. Therefore, the introduction section must be revised accordingly. * The presentation of t...
- 1 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 65 (1) , 96-103
Screen Printed Polarization Independent Microwave Absorber for Wideband RCS Reduction
Designing and deploying a broadband microwave absorber that provides wide bandwidth radar cross section (RCS) reduction for planar and curved surfaces is challenging. We present a resistive ink-based multilayered wideband absorber using a low-priced FR4 substrate to cope with the challenge. The reflection coefficient response of the structure lies beneath −10 dB reference over the frequency span of 1.3–18.6 GHz for the normally incident electromagnetic waves. The multilayered structure incorporates the entire microwave radar frequency span with a relative fractional bandwidth of 173.86%. Moreover, to examine the applicability of the structure for a nonplanar geometrical surface, we further design the structure on a very thin FR4 substrate that can be bent easily. We performed an RCS analysis of the redesigned structure under monostatic and bistatic conditions. The structure thereby exhibits novelty in terms of wider stealth and electromagnetic compatibility applications and also a good counterbalance among different design attributes comprising thickness, bandwidth, and periodicity, unlike the earlier reported work. The proposed prototypes are fabricated and experimentally validated for planar and curved surfaces, respectively. The experimental results depict a good concurrence with the simulated results.
- 1 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 65 (1) , 96-103
Screen Printed Polarization Independent Microwave Absorber for Wideband RCS Reduction
Designing and deploying a broadband microwave absorber that provides wide bandwidth radar cross section (RCS) reduction for planar and curved surfaces is challenging. We present a resistive ink-based multilayered wideband absorber using a low-priced FR4 substrate to cope with the challenge. The reflection coefficient response of the structure lies beneath −10 dB reference over the frequency span of 1.3–18.6 GHz for the normally incident electromagnetic waves. The multilayered structure incorporates the entire microwave radar frequency span with a relative fractional bandwidth of 173.86%. Moreover, to examine the applicability of the structure for a nonplanar geometrical surface, we further design the structure on a very thin FR4 substrate that can be bent easily. We performed an RCS analysis of the redesigned structure under monostatic and bistatic conditions. The structure thereby exhibits novelty in terms of wider stealth and electromagnetic compatibility applications and also a good counterbalance among different design attributes comprising thickness, bandwidth, and periodicity, unlike the earlier reported work. The proposed prototypes are fabricated and experimentally validated for planar and curved surfaces, respectively. The experimental results depict a good concurrence with the simulated results.
- 17 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 21 (9) , 1887-1891
A Compact, Low-Profile Shorted TM$_{1/2,0}$ Mode Planar Copolarized Microstrip Antenna for Full-Duplex Systems
In this letter, a single-layer compact copolarized shorted TM 1/2,0 mode microstrip patch antenna is presented for in-band full-duplex application. Two shorted TM 1/2,0 mode patch antennas, used for transmission and reception purposes, make the structure compact. The wideband behavior of the patch antenna is obtained by fusing the two resonances, one because of the shorted TM 1/2,0 mode radiating patch and the other because of the λ/4 line resonator. To enhance the isolation between the transmitter and receiver antenna, a novel defected ground structure is used. Slots are introduced into the ground plane to create a weak field region for the basic antenna element. The other antenna element (receiver) is located in the weak field region to enhance isolation. Further enhancement in isolation is achieved by introducing a T-shaped metallic strip into the slots. The structure is proposed with the credits of compactness, enhanced bandwidth, colinear polarization, very less fabrication complexity, low profile, and high isolation. The proposed structure is fabricated and measured. The structure experimentally exhibits a bandwidth (≤ −10 dB) of 2.42–2.52 GHz with the isolation of 25 dB, peak isolation of 36 dB, and an average realized gain of 4 dBi in the entire band.
- 17 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 21 (9) , 1887-1891
A Compact, Low-Profile Shorted TM$_{1/2,0}$ Mode Planar Copolarized Microstrip Antenna for Full-Duplex Systems
In this letter, a single-layer compact copolarized shorted TM 1/2,0 mode microstrip patch antenna is presented for in-band full-duplex application. Two shorted TM 1/2,0 mode patch antennas, used for transmission and reception purposes, make the structure compact. The wideband behavior of the patch antenna is obtained by fusing the two resonances, one because of the shorted TM 1/2,0 mode radiating patch and the other because of the λ/4 line resonator. To enhance the isolation between the transmitter and receiver antenna, a novel defected ground structure is used. Slots are introduced into the ground plane to create a weak field region for the basic antenna element. The other antenna element (receiver) is located in the weak field region to enhance isolation. Further enhancement in isolation is achieved by introducing a T-shaped metallic strip into the slots. The structure is proposed with the credits of compactness, enhanced bandwidth, colinear polarization, very less fabrication complexity, low profile, and high isolation. The proposed structure is fabricated and measured. The structure experimentally exhibits a bandwidth (≤ −10 dB) of 2.42–2.52 GHz with the isolation of 25 dB, peak isolation of 36 dB, and an average realized gain of 4 dBi in the entire band.
- 11 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 21 (2) , 257-261
A Miniaturized Frequency Selective Rasorber With Independently Regulated Selective Dual-Transmission Response
In this letter, a miniaturized-element dual-polarized frequency selective rasorber (FSR) with independently regulated dual-transmission response has been presented. The proposed FSR is made of two cascaded layers separated by an air spacer, where the top lossy layer provides wideband absorption along with in-band transmission and the bottom lossless layer exhibits a dual bandpass filter. The novelty of the proposed design lies in the use of lumped capacitors in the top layer to realize the independently controlled highly selective transmission frequencies as well as attain a miniaturized unit cell topology (having dimensions of 0.08 λ L × 0.08 λ L , λ L being the lowest operating frequency). In addition, convoluted slot geometries are patterned in the bottom layer to obtain the transmission bands appearing at the same frequencies as that of the top layer. The proposed structure has an operating range of 1.87–7.97 GHz, whereas two distinct transmission responses are located at 3.52 and 5 GHz having insertion losses of 1.2 and 0.82 dB, respectively. Furthermore, the geometry exhibits an angularly stable performance upto 40° for both TE and TM polarizations. A prototype of the proposed FSR was fabricated and measured to validate the simulated responses under normal incidence.
- 11 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 21 (2) , 257-261
A Miniaturized Frequency Selective Rasorber With Independently Regulated Selective Dual-Transmission Response
In this letter, a miniaturized-element dual-polarized frequency selective rasorber (FSR) with independently regulated dual-transmission response has been presented. The proposed FSR is made of two cascaded layers separated by an air spacer, where the top lossy layer provides wideband absorption along with in-band transmission and the bottom lossless layer exhibits a dual bandpass filter. The novelty of the proposed design lies in the use of lumped capacitors in the top layer to realize the independently controlled highly selective transmission frequencies as well as attain a miniaturized unit cell topology (having dimensions of 0.08 λ L × 0.08 λ L , λ L being the lowest operating frequency). In addition, convoluted slot geometries are patterned in the bottom layer to obtain the transmission bands appearing at the same frequencies as that of the top layer. The proposed structure has an operating range of 1.87–7.97 GHz, whereas two distinct transmission responses are located at 3.52 and 5 GHz having insertion losses of 1.2 and 0.82 dB, respectively. Furthermore, the geometry exhibits an angularly stable performance upto 40° for both TE and TM polarizations. A prototype of the proposed FSR was fabricated and measured to validate the simulated responses under normal incidence.