ALAnatolii Lisoval

Anatolii Lisoval

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Anatolii Lisoval has a total of 8 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Study of Diesel Engine Fuel Consumption with the Help of a Digital Twin

    by Oleksiy Verbovskyi, Anatolii Lisoval, Hennadiy Zhuk, Valerii Verbovskyi, Anatolii Dzygar

  • Open Access

    JUSTIFICATION FOR USING SYNTHESISED E-FUELS IN THE DIESEL ENGINES OF VEHICLES

    by A.A. Lisoval, O.F. Hovorov, V.L. Pukas, M.P. Volynkin

    Based on foreign sources, the article systematises and summarises the results of recent studies on the possibilities of using synthesised electronic fuels (e-fuels) in land transport for the gradual decarbonisation of the industry. The article focuses on liquid e-fuels for transport diesel engines. Diesel engines remain a relevant subject of research for Ukraine today, as they are used in vehicles not only for transporting goods, but also for the mobility of the defence sector and technological processes in food production. EU countries plan to reduce greenhouse gas emissions by 55 % by 2030 and achieve carbon neutrality by 2050. In this context, e-fuels have become a promising solution for reducing greenhouse gas emissions in transport. Classic e-fuels are synthesized from CO2 captured from the air and renewable hydrogen obtained by electrolysis of water. The energy for electrolysis comes from renewable sources of wind, solar, geothermal, tidal, or hydroelectric power. The main advantages of e-fuels are that they are produced from renewable energy sources and use existing fuel infrastructure with minimal changes. E-fuel production is not yet available on a large scale. Its use will gradually increase thanks to a phased increase in its concentration in blended fuels. At the same time, other similar carbon-neutral technologies will be introduced in transport. The first step towards carbon-neutral e-fuels is the introduction of paraffin fuels obtained from bio-raw materials using renewable energy sources. Such introduction in transport diesel engines ensures a reduction in CO2, soot and other harmful emissions. This is an intermediate stage until the mass production of purely synthetic paraffin e-fuels. The use of synthesised OMEx and DME e-esters in diesel engines as low-carbon fuels is possible in the short and medium term. This is the second step towards the spread of carbon-neutral e-fuels and technologies in transport. Before introducing such fuels, additional research is needed on their compatibility with diesel materials. Ukraine has an outdated fleet of vehicles that cannot be instantly replaced with new, more efficient ones. Research and development aimed at the phased introduction of carbon-neutral e-fuels in transport should minimise the harmful impact of existing motor vehicles on the environment.

  • Open Access

    BACKGROUND FOR THE USE OF HYDROGEN IN UKRAINE IN THE ENERGY AND AUTOMOTIVE SECTORS

    by A.A. Lisoval

    В статті на підставі світових тенденцій обґрунтовано місце водню і водневих технологій в подальших процесах декарбонізації енергетики і автомобільного транспорту України. Різноманітність способів виробництва, транспортування та зберігання, використання водню різної чистоти вимагають складних компромісних рішень між вартістю технології і кількістю можливих викидів шкідливих речовин у довкілля на всіх супутніх етапах застосування цих технологій. Водневе паливо і водневі технології слід позиціонувати як один із напрямів енергетичного переходу галузей економіки на рейки декарбонізації, що приведе до створення кліматично нейтральних технологій. Традиційні поршневі двигуни внутрішнього згорання можна модернізувати для роботи на суто водневому паливі, але це потребує застосування нових матеріалів через високу питому енергоємність водню. На шляху спалювання водню в камерах згорання ДВЗ стоять обмеження на викиди оксидів азоту NOX. Можливий варіант використання суміші водню з природним газом або модернізація двопаливних ДВЗ. Це найбільш реалістичний варіант на поточний час для України. В світлі процесів декарбонізації, головною перевагою паливних елементів (ПЕ) є відсутність згорання вуглеводнів і відповідно  можливість зменшити забруднення атмосферного повітря парниковим газом СО2.  Існуючі ПЕ можуть працювати не лише на водні, а і на природному газі. В енергетиці водневі технології конкурують не з традиційними способами отримання тепла та електричної енергії, а з біоенергетикою, з тепловими насосами, з технологіями уловлювання та зберігання вуглецю та його оксидів. В автомобільній галузі водневі технології конкурують з рідкими і газоподібними біопаливами, електромобілями та гібридами з ДВЗ і акумуляторами. Потенціальні можливості застосування  водневих технологій для процесів декарбонізації  розкриються тільки після створення ринку продажу водню та відповідної інфраструктури. На сегмент і ціну застосування водневих технологій впливає спосіб вибраного процесу виробництва, складових інфраструктури, які включають зберігання, транспортування і заправні станції. Безпечна експлуатація і впровадження  водневих технологій в Україні потребує кваліфікованих інженерних кадрів. Підготовку таких спеціалістів для енергетики і транспорту можуть взяти на себе університети за спеціальністю 142 – енергетичне машинобудування.

  • Open Access

    USE OF BIOGAS AS A RAW MATERIAL AND ENGINE FUEL IN ENERGY AND TRANSPORT

    by A.A. Lisoval

    In the article, based on existing global trends, legislative incentives for climate-friendly development of economic sectors, the place of biogas as a raw material and engine fuel in the decarbonization of energy and transport in Ukraine is substantiated. To reduce greenhouse gas emissions, most countries are making the transition from fossil fuels to renewable energy sources. In EU countries, renewable energy with a Green Deal label was equated with energy obtained from the combustion of natural gas. In Ukraine, biomethane is legislated as an alternative gas fuel similar to natural gas. The raw material for biomethane is biogas. In Ukraine, biomethane is not produced on an industrial scale due to the lack of special purification and enrichment technologies at biogas stations. In Ukraine, it is necessary to start producing biomethane on an industrial scale and use the natural gas infrastructure for transporting biomethane. An existing quantity and quality of treatment technologies of biogas plants allow the use of biogas as an independent fuel in cogeneration plants in the immediate vicinity of biogas plants. Calculation of the heat balance of the drive gas engine (8-cylinder, 100 mm cylinder diameter, 88 mm stroke) showed that in addition to generating 30 kW of electrical energy, it is possible to obtain additionally up to 162 MJ of thermal energy without taking heat from the lubrication system. When generating only electrical energy, the efficiency installation in nominal mode is about 30%, and with cogeneration – it increases to 75%. The next step is – the use of biogas as an additive to natural gas in reciprocating internal combustion engines on cars, buses and special agricultural machinery at the local or regional level. The results of research on the 8Ch10/8.8 gas combustion engine ensured the transition from quantitative to qualitative regulation of the fuel mixture of natural gas with biogas additives. An interdependent regulation algorithm has been developed for mixed fuel. With an increase in load, the share of biogas decreases, the mixture is enriched with natural gas. At a load of 75% or more, the enrichment of the fuel mixture occurs more intensively.


  • Open Access

    RELATED REGULATION OF BIOGAS SUPPLIES AND METHANE IN A GAS ENGINE

    by А.а. Lisoval

    The results of experimental researches were received on a gas-electric installation with a rated power of 30 kW at 1500 rpm. The spark-ignited petrol drive engine (8-cylinder, 100 mm cylinder diameter, 88 mm stroke) was converted to a pure gas one. The compression ratio of 8.5 did not change. The gas fuel supply system consists of a supply line and an emergency shut-off circuit. The natural gas supply line was connected to the domestic main line through a special gas distributor. On the basis of HEINZMANN components, a system for dosing mixed gas fuel was developed, which, through a microprocessor control unit and an actuator, acted on the throttle valve of the gas mixer. In experimental researches, the composite fuel was a model gas – a mixture of natural and carbon dioxide gases, which was prepared in a zero pressure reducer before the gas mixer. With an increase in the volume fraction of carbon dioxide in the model gas by more than 34 %, a deterioration of the combustion process was observed in the steady state. In the article, based on the analysis of the experimental results of the operation of a piston gas engine on a model gas, an algorithm for the use of associated automatic control of biogas and methane feeds is substantiated. The transition from quantitative to qualitative regulation of the gas-air mixture has been substantiated. To do this, it is necessary to create two automatic control loops for the supply of air and a mixture of natural gas, which are interconnected through an external load. With the developed algorithm, as the load increases, the supply of natural gas increases, and the supply of biogas decreases. With an increase in the load of 75 % or more, a more intensive enrichment of the fuel mixture with natural gas occurs than at low and medium loads. The proposed algorithm for regulating the fuel mixture can be implemented using electromagnetic gas injectors for dosing the components of the composite fuel. Signals from sensors for oxygen and methane content in exhaust gases were selected as corrective links for the coupled control algorithm. Recommendations on the choice of tuning modes for oxygen and methane sensors have been developed.

  • RESEARCH OPPORTUNITIES OF ROTREX SUPERCHARGER FOR APPLICATION IN EXHAUST SYSTEMS

    by Lisoval A

    The purpose of the article is to describe the design and research of the new Rotrex superchargers of C15 series. In superchargers to ensure high boost pressure and efficiency centrifugal compressor wheel, shockless planetary gear of the original design, a special lubrication-cooling system were used. The article describes the design features of Rotrex centrifugal superchargers and the results of experimental researches of the C15 series supercharger on a motor less stand. The design feature of the C15 series superchargers is compactness and high speed - the compressor wheel speed reaches 200 000 rpm. In a planetary gear, cylindrical rollers on ball bearings are used instead of gear satellites. The gear ratio from the shaft of the stand motor to the shaft of the compressor wheel was 43. Tests of the C15-20 supercharger are performed in static modes. Characteristics of the consumer of boost air were modeled with special washers with minimum diameters of 10,1 ... 14,0 mm. The maximum overpressure of 1.1 ... 1.3 MPa was achieved at a flow rate of 460 ... 250 kg/h, respectively. The tests confirmed the efficiency of the stand for gas-dynamic research of centrifugal compressors, the electronic control system of the electric motor current frequency reliably worked. Characteristics of the C15-20 supercharger, test results confirmed its purpose for spark-ignition car engines. They can be used in combined boost systems of both gasoline engines and diesel engines. KEY WORDS: INTERNAL COMBUSTION ENGINE, BOOST, CENTRIFUGAL SUPERCHARGER, BOOST TESTS