Olli Eemeli Setälä
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Olli Eemeli Setälä has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Ville Vähänissi
Aalto University
8 shared publications - Hele Savin
Aalto University
6 shared publications - Behrad Radfar
Department of Electronics and Nanoengineering Aalto University Tietotie 3 02150 Espoo Finland
4 shared publications - Toni P. Pasanen
Department of Electronics and Nanoengineering Aalto University Tietotie 3 Espoo 02150 Finland
4 shared publications - Kexun Chen
Department of Electronics and Nanoengineering, Aalto University, Espoo, Finland
3 shared publications - Xiaolong Liu
Aalto University
3 shared publications
Latest Publications
- Open Access
- 8 May 2026
- Published by Elsevier in SSRN Electronic Journal
Reducing Al/p-Si contact resistivity by utilizing Al2O3 induced surface accumulation
Here we study how much our previously proposed dopant free ohmic contacts, called induced contacts, are able to reduce the contact resistivity of a p-type ohmic contact. The induced contacts do not utilize any external doping but only a highly charged atomic layer deposited (ALD) Al2O3 thin film. The negative charge in the Al2O3 induces a p+ accumulation layer to the substrate surface, increasing the surface carrier concentration and lowering the contact resistivity. The results show that the Al2O3 induced contacts significantly decrease the contact resistivity of Al/p-Si contacts, and the narrower the contact the more pronounced the decrease is. The narrowest contacts studied here have a width of 3 μm, and the Al2O3 improves the contact resistivity from a reference value of 11.13 mΩ⋅cm2 to 0.90 mΩ⋅cm2 on a planar surface. An even larger improvement is observed with surface nanostructured samples, for which the contact resistivity reduced from 10.03 mΩ⋅cm2 to 0.73 mΩ⋅cm2. An analytical model is derived to help understand how dimensions affect the contact resistivity and to predict the contact resistivities at given dimensions. The model suggests theoretically lowest contact resistivity values of 1.0 µΩ⋅cm2 and 0.1 µΩ⋅cm2 for planar and nanostructured induced contacts, respectively.
- 8 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessReducing Al/p-Si contact resistivity by utilizing Al2O3 induced surface accumulation
Here we study how much our previously proposed dopant free ohmic contacts, called induced contacts, are able to reduce the contact resistivity of a p-type ohmic contact. The induced contacts do not utilize any external doping but only a highly charged atomic layer deposited (ALD) Al2O3 thin film. The negative charge in the Al2O3 induces a p+ accumulation layer to the substrate surface, increasing the surface carrier concentration and lowering the contact resistivity. The results show that the Al2O3 induced contacts significantly decrease the contact resistivity of Al/p-Si contacts, and the narrower the contact the more pronounced the decrease is. The narrowest contacts studied here have a width of 3 μm, and the Al2O3 improves the contact resistivity from a reference value of 11.13 mΩ⋅cm2 to 0.90 mΩ⋅cm2 on a planar surface. An even larger improvement is observed with surface nanostructured samples, for which the contact resistivity reduced from 10.03 mΩ⋅cm2 to 0.73 mΩ⋅cm2. An analytical model is derived to help understand how dimensions affect the contact resistivity and to predict the contact resistivities at given dimensions. The model suggests theoretically lowest contact resistivity values of 1.0 µΩ⋅cm2 and 0.1 µΩ⋅cm2 for planar and nanostructured induced contacts, respectively.
- Open Access
CMOS Image Sensor for Broad Spectral Range with >90% Quantum Efficiency
Even though the recent progress made in complementary metal–oxide–semiconductor (CMOS) image sensors (CIS) has enabled numerous applications affecting our daily lives, the technology still relies on conventional methods such as antireflective coatings and ion‐implanted back‐surface field to reduce optical and electrical losses resulting in limited device performance. In this work, these methods are replaced with nanostructured surfaces and atomic layer deposited surface passivation. The results show that such surface nanoengineering applied to a commercial backside illuminated CIS significantly extends its spectral range and enhances its photosensitivity as demonstrated by >90% quantum efficiency in the 300–700 nm wavelength range. The surface nanoengineering also reduces the dark current by a factor of three. While the photoresponse uniformity of the sensor is seen to be slightly better, possible scattering from the nanostructures can lead to increased optical crosstalk between the pixels. The results demonstrate the vast potential of surface nanoengineering in improving the performance of CIS for a wide range of applications.
Open AccessCMOS Image Sensor for Broad Spectral Range with >90% Quantum Efficiency
Even though the recent progress made in complementary metal–oxide–semiconductor (CMOS) image sensors (CIS) has enabled numerous applications affecting our daily lives, the technology still relies on conventional methods such as antireflective coatings and ion‐implanted back‐surface field to reduce optical and electrical losses resulting in limited device performance. In this work, these methods are replaced with nanostructured surfaces and atomic layer deposited surface passivation. The results show that such surface nanoengineering applied to a commercial backside illuminated CIS significantly extends its spectral range and enhances its photosensitivity as demonstrated by >90% quantum efficiency in the 300–700 nm wavelength range. The surface nanoengineering also reduces the dark current by a factor of three. While the photoresponse uniformity of the sensor is seen to be slightly better, possible scattering from the nanostructures can lead to increased optical crosstalk between the pixels. The results demonstrate the vast potential of surface nanoengineering in improving the performance of CIS for a wide range of applications.
- Open Access
- 22 May 2023
- Published by American Chemical Society (ACS) in ACS Photonics
- Vol. 10 (6) , 1735-1741
Boron-Implanted Black Silicon Photodiode with Close-to-Ideal Responsivity from 200 to 1000 nm
Detection of UV light has traditionally been a major challenge for Si photodiodes due to reflectance losses and junction recombination. Here we overcome these problems by combining a nanostructured surface with an optimized implanted junction and compare the obtained performance to state-of-the-art commercial counterparts. We achieve a significant improvement in responsivity, reaching near ideal values at wavelengths all the way from 200 to 1000 nm. Dark current, detectivity, and rise time are in turn shown to be on a similar level. The presented detector design allows a highly sensitive operation over a wide wavelength range without making major compromises regarding the simplicity of the fabrication or other figures of merit relevant to photodiodes.
- 22 May 2023
- Published by American Chemical Society (ACS) in ACS Photonics
- Vol. 10 (6) , 1735-1741
Open AccessBoron-Implanted Black Silicon Photodiode with Close-to-Ideal Responsivity from 200 to 1000 nm
Detection of UV light has traditionally been a major challenge for Si photodiodes due to reflectance losses and junction recombination. Here we overcome these problems by combining a nanostructured surface with an optimized implanted junction and compare the obtained performance to state-of-the-art commercial counterparts. We achieve a significant improvement in responsivity, reaching near ideal values at wavelengths all the way from 200 to 1000 nm. Dark current, detectivity, and rise time are in turn shown to be on a similar level. The presented detector design allows a highly sensitive operation over a wide wavelength range without making major compromises regarding the simplicity of the fabrication or other figures of merit relevant to photodiodes.
- Open Access
- 24 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (7) , 6750-6756
Excellent Responsivity and Low Dark Current Obtained With Metal-Assisted Chemical Etched Si Photodiode
Metal-assisted chemical etched (MACE, also known as MacEtch or MCCE) nanostructures are utilized widely in the solar cell industry due to their excellent optical properties combined with a simple and cost-efficient fabrication process. The photodetection community, on the other hand, has not shown much interest towards MACE due to its drawbacks including insufficient surface passivation, increased junction recombination, and possible metal contamination, which are especially detrimental to pn-photodiodes. Here, we aim to change this by demonstrating how to fabricate high-performance MACE pn-photodiodes with above 90% external quantum efficiency (EQE) without external bias voltage at 200–1000 nm and dark current less than 3 nA/cm 2 at -5 V using industrially applicable methods. The key is to utilize an induced junction created by an atomic layer deposited highly charged Al 2 O 3 thin film that simultaneously provides efficient field-effect passivation and full conformality over the MACE nanostructures. Achieving close to ideal performance demonstrates the vast potential of MACE nanostructures in the fabrication of high-performance low-cost pn-photodiodes.
- 24 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (7) , 6750-6756
Open AccessExcellent Responsivity and Low Dark Current Obtained With Metal-Assisted Chemical Etched Si Photodiode
Metal-assisted chemical etched (MACE, also known as MacEtch or MCCE) nanostructures are utilized widely in the solar cell industry due to their excellent optical properties combined with a simple and cost-efficient fabrication process. The photodetection community, on the other hand, has not shown much interest towards MACE due to its drawbacks including insufficient surface passivation, increased junction recombination, and possible metal contamination, which are especially detrimental to pn-photodiodes. Here, we aim to change this by demonstrating how to fabricate high-performance MACE pn-photodiodes with above 90% external quantum efficiency (EQE) without external bias voltage at 200–1000 nm and dark current less than 3 nA/cm 2 at -5 V using industrially applicable methods. The key is to utilize an induced junction created by an atomic layer deposited highly charged Al 2 O 3 thin film that simultaneously provides efficient field-effect passivation and full conformality over the MACE nanostructures. Achieving close to ideal performance demonstrates the vast potential of MACE nanostructures in the fabrication of high-performance low-cost pn-photodiodes.
- Open Access
- 13 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Semiconductor Manufacturing
- Vol. 35 (3) , 504-510
Perspectives on Black Silicon in Semiconductor Manufacturing: Experimental Comparison of Plasma Etching, MACE, and Fs-Laser Etching
In semiconductor manufacturing, black silicon (bSi) has traditionally been considered as a sign of unsuccessful etching. However, after more careful consideration, many of its properties have turned out to be so superior that its integration into devices has become increasingly attractive. In devices where bSi covers the whole wafer surface, such as solar cells, the integration is already rather mature and different bSi fabrication technologies have been studied extensively. Regarding the integration into devices where bSi should cover only small selected areas, existing research focuses on device properties with one specific bSi fabrication method. Here, we fabricate bSi patterns with varying dimensions ranging from millimeters to micrometers using three common bSi fabrication techniques, i.e., plasma etching, metal-assisted chemical etching (MACE) and femtosecond-laser etching, and study the corresponding fabrication characteristics and resulting material properties. Our results show that plasma etching is the most suitable method in the case of $\mu \text{m}$ -scale devices, while MACE reaches surprisingly almost the same performance. Femtosecond-laser has potential due to its maskless nature and capability for hyperdoping, however, in this study its moderate accuracy, large silicon consumption and spreading of the etching damage outside the bSi region leave room for improvement.
- 13 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Semiconductor Manufacturing
- Vol. 35 (3) , 504-510
Open AccessPerspectives on Black Silicon in Semiconductor Manufacturing: Experimental Comparison of Plasma Etching, MACE, and Fs-Laser Etching
In semiconductor manufacturing, black silicon (bSi) has traditionally been considered as a sign of unsuccessful etching. However, after more careful consideration, many of its properties have turned out to be so superior that its integration into devices has become increasingly attractive. In devices where bSi covers the whole wafer surface, such as solar cells, the integration is already rather mature and different bSi fabrication technologies have been studied extensively. Regarding the integration into devices where bSi should cover only small selected areas, existing research focuses on device properties with one specific bSi fabrication method. Here, we fabricate bSi patterns with varying dimensions ranging from millimeters to micrometers using three common bSi fabrication techniques, i.e., plasma etching, metal-assisted chemical etching (MACE) and femtosecond-laser etching, and study the corresponding fabrication characteristics and resulting material properties. Our results show that plasma etching is the most suitable method in the case of $\mu \text{m}$ -scale devices, while MACE reaches surprisingly almost the same performance. Femtosecond-laser has potential due to its maskless nature and capability for hyperdoping, however, in this study its moderate accuracy, large silicon consumption and spreading of the etching damage outside the bSi region leave room for improvement.
- 29 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 33 (24) , 1415-1418
Harnessing Carrier Multiplication in Silicon Solar Cells Using UV Photons
Silicon solar cells are known to suffer from poor emitter performance that is seen as reduced external quantum efficiency at wavelengths below 500 nm. This is due to common tradeoff between electrical and optical performance. Here we demonstrate that no such tradeoff is needed when optimized boron implantation parameters are combined with non-reflective nanostructures and atomic layer deposited Al 2 O 3 surface passivation. As a result, in our solar cells the external quantum efficiency actually increases with decreasing wavelength and reaches even above 100% at short wavelengths. This result indicates that carrier multiplication caused by absorption of high energy photons could be utilized for energy production in solar cells.
- 29 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 33 (24) , 1415-1418
Harnessing Carrier Multiplication in Silicon Solar Cells Using UV Photons
Silicon solar cells are known to suffer from poor emitter performance that is seen as reduced external quantum efficiency at wavelengths below 500 nm. This is due to common tradeoff between electrical and optical performance. Here we demonstrate that no such tradeoff is needed when optimized boron implantation parameters are combined with non-reflective nanostructures and atomic layer deposited Al 2 O 3 surface passivation. As a result, in our solar cells the external quantum efficiency actually increases with decreasing wavelength and reaches even above 100% at short wavelengths. This result indicates that carrier multiplication caused by absorption of high energy photons could be utilized for energy production in solar cells.
- Open Access
- 2 July 2021
- Published by Wiley in Physica Status Solidi (a)
- Vol. 218 (23)
Al‐neal Degrades Al2O3 Passivation of Silicon Surface
Atomic layer deposited (ALD) aluminum oxide (Al2O3) has emerged as a useful material for silicon devices due to its capability for effective surface passivation and ability to generate p+ region underneath the oxide as active or passive component in semiconductor devices. However, it is uncertain how Al2O3 films tolerate the so‐called Al‐neal treatment that is a necessary process step in devices that also contain silicon dioxide (SiO2) passivation layers. Herein, it is reported that the Al‐neal process is harmful for the passivation performance of Al2O3 causing over eightfold increase in surface recombination velocity (SRV) (from 0.9 to 7.3 cm s−1). Interestingly, it is also observed that the stage at which the so‐called activation of Al2O3 passivation is performed impacts the final degradation strength. The best result is obtained when the activation step is done at the end of the process together with the Al‐neal thermal treatment, which results in SRV of 1.7 cm s−1. The results correlate well with the measured interface defect density, indicating that the Al‐neal affects defects at the Si/SiO x /Al2O3 interface. The root causes for the defect reactions are discussed and possible reasons for the observed phenomena are suggested.
- 2 July 2021
- Published by Wiley in Physica Status Solidi (a)
- Vol. 218 (23)
Open AccessAl‐neal Degrades Al2O3 Passivation of Silicon Surface
Atomic layer deposited (ALD) aluminum oxide (Al2O3) has emerged as a useful material for silicon devices due to its capability for effective surface passivation and ability to generate p+ region underneath the oxide as active or passive component in semiconductor devices. However, it is uncertain how Al2O3 films tolerate the so‐called Al‐neal treatment that is a necessary process step in devices that also contain silicon dioxide (SiO2) passivation layers. Herein, it is reported that the Al‐neal process is harmful for the passivation performance of Al2O3 causing over eightfold increase in surface recombination velocity (SRV) (from 0.9 to 7.3 cm s−1). Interestingly, it is also observed that the stage at which the so‐called activation of Al2O3 passivation is performed impacts the final degradation strength. The best result is obtained when the activation step is done at the end of the process together with the Al‐neal thermal treatment, which results in SRV of 1.7 cm s−1. The results correlate well with the measured interface defect density, indicating that the Al‐neal affects defects at the Si/SiO x /Al2O3 interface. The root causes for the defect reactions are discussed and possible reasons for the observed phenomena are suggested.